Installation Guide for luminii models including: BA42WET, BA42WET Linear LED Strip, Linear LED Strip, LED Strip, Strip
B45R Channel - Luminii
File Info : application/pdf, 7 Pages, 637.83KB
DocumentDocumentInstallation Instructions for Basics Models BA42WET Please read all instructions prior to installation and keep for future reference! 1. Product should be installed by a qualified electrician. 2. Prior to installation ensure power is off at fuse box to prevent electrical shock. 3. Use only with Class 2 power unit. Utiliser seulement avec Classe 2 unite d'alimentation electrique. 4. Suitable for wet Locations. Convient Aux Emplacements Humides. 5. For under-cabinet or shelf mount. 6. Conforms to UL STD 2108. Certified to CSA STD C22.2 No.250.0. Installation directly to mounting surface with factory lead wire REV0.1 02222024 1 / 7 7777 Merrimac Ave Niles, IL 60714 T 224.333.6033 F 224.757.7557 info@luminii.com www.luminii.com 1 solder pads LED strip Attention: Always test BA42WET strip operation before installing. Connect BA42WET strip to power supply to ensure it is working properly and no damage has occured during shipping. factory lead wire 1.1 If length of BA42WET strip needs to be shortened on the job site, simply cut the LED strip in the between solder pads. Always cut from the end with no wire leads. EC-10MM-WET EC-10MM-WET 1.2 If the cut end doesn not need a powerfeed connector, insert the silicone end cap (EC-10MM-WET) over the BA42WET LED strip and add silicone (SIL-502-RTV) to water proof seal the end. SIL-502-RTV Silicone Sealent *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATIONS WITHOUT NOTICE Installation Instructions for Basics Models BA42WET Please read all instructions prior to installation and keep for future reference! 1. Product should be installed by a qualified electrician. 2. Prior to installation ensure power is off at fuse box to prevent electrical shock. 3. Use only with Class 2 power unit. Utiliser seulement avec Classe 2 unite d'alimentation electrique. 4. Suitable for wet Locations. Convient Aux Emplacements Humides. 5. For under-cabinet or shelf mount. 6. Conforms to UL STD 2108. Certified to CSA STD C22.2 No.250.0. REV0.1 02222024 2 / 7 7777 Merrimac Ave Niles, IL 60714 T 224.333.6033 F 224.757.7557 info@luminii.com www.luminii.com 2 2.1 Clean the area thoroughly where the BA42WET strip will be installed. 2.2 Remove the paper backing from the BA42WET strip and firmly press down making sure there are no air bubbles that cancause surface irregularities. 2.3 Install LL-ZIP Strain Relief Clip 3" away from the end of the strip. ripple LL-ZIP Strain Relief Clip paper backing NOTE - When removing backing & laying Express strip to surface avoid ripples. NOTE - Avoid bending the Express strip in flat bends which may damage the LEDs. 3 3.1 Install one CL2 mounting clip every 12", in between the LED diodes. 3.2 Secure using the provided screws. 3" Note: Recommended to be used when LineLED installed on textured or on a non-stick surface. 12" CL2 Mounting Clip *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATIONS WITHOUT NOTICE Installation Instructions for Basics Models BA42WET Please read all instructions prior to installation and keep for future reference! 1. Product should be installed by a qualified electrician. 2. Prior to installation ensure power is off at fuse box to prevent electrical shock. 3. Use only with Class 2 power unit. Utiliser seulement avec Classe 2 unite d'alimentation electrique. 4. Suitable for wet Locations. Convient Aux Emplacements Humides. 5. For under-cabinet or shelf mount. 6. Conforms to UL STD 2108. Certified to CSA STD C22.2 No.250.0. REV0.1 02222024 3 / 7 7777 Merrimac Ave Niles, IL 60714 T 224.333.6033 F 224.757.7557 info@luminii.com www.luminii.com 4 4.1 Place the strain relief in desired place. Make sure it is 3" away from the end of the strip. 4.2 Slide the ziptie through strain relief opening. 4.3 Lay wire lead on top of strain relief. 4.4 Tighten zip tie around lead wire. Cut off excess zip tie. Screw Wire lead LL-ZIP Strain relief Zip tie Can also be placed horizontally as an option. *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATIONS WITHOUT NOTICE Installation Instructions for Basics Models BA42WET Please read all instructions prior to installation and keep for future reference! 1. Product should be installed by a qualified electrician. 2. Prior to installation ensure power is off at fuse box to prevent electrical shock. 3. Use only with Class 2 power unit. Utiliser seulement avec Classe 2 unite d'alimentation electrique. 4. Suitable for wet Locations. Convient Aux Emplacements Humides. 5. For under-cabinet or shelf mount. 6. Conforms to UL STD 2108. Certified to CSA STD C22.2 No.250.0. Installation Directly to Mounting Surface using BA Connectors REV0.1 02222024 4 / 7 7777 Merrimac Ave Niles, IL 60714 T 224.333.6033 F 224.757.7557 info@luminii.com www.luminii.com Jumper connector BA-WET-PJC-10-03 Mounting clip CL2 LED strip BA42WET 1 solder pads LED strip BA42WET Power feed connector BA-WET-PFC-10-72 Strain Relief Clip LL-ZIP LED strip run start 1.1 If length of BA42WET strip needs to be shortened on the job site, simply cut the LED strip in the between solder pads. Always cut from the end with no wire leads. EC-10MM-WET EC-10MM-WET SIL-502-RTV Silicone Sealent 1.2 If the cut end doesn not need a powerfeed connector, insert the silicone end cap (EC-10MM-WET) over the BA42WET LED strip and add silicone (SIL-502-RTV) to water proof seal the end. *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATIONS WITHOUT NOTICE Installation Instructions for Basics Models BA42WET Please read all instructions prior to installation and keep for future reference! 1. Product should be installed by a qualified electrician. 2. Prior to installation ensure power is off at fuse box to prevent electrical shock. 3. Use only with Class 2 power unit. Utiliser seulement avec Classe 2 unite d'alimentation electrique. 4. Suitable for wet Locations. Convient Aux Emplacements Humides. 5. For under-cabinet or shelf mount. 6. Conforms to UL STD 2108. Certified to CSA STD C22.2 No.250.0. REV0.1 02222024 5 / 7 7777 Merrimac Ave Niles, IL 60714 T 224.333.6033 F 224.757.7557 info@luminii.com www.luminii.com 2 Connector 2.1 Check the polarity,refer to the plus sign on powerfeed cap. Then remove paper backing on the end of LED Strip. Insert LED strip into tube, push the strip until it touches the end wall in tube. 2.2 Add silicone sealent into the tube. Plus sign 2.3 Sanp on power feed cap, push it down until hearing a "click". Tube Power feed cap Tube LED Strip SIL-502-RTV Silicone Sealent 3 3.1 Clean the area thoroughly where the BA42WET strip will be installed. 3" 3.2 Remove the paper backing from the BA42WET strip and firmly press down making sure there are no air bubbles that can cause surface irregularities 3.3 Install LL-ZIP Strain Relief Clip 3" away from the end of the strip. ripple LL-ZIP Strain Relief Clip adhesive tape NOTE - When removing backing & laying Express strip to surface avoid ripples. NOTE - Avoid bending the Express strip in flat bends which may damage the LEDs. *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATIONS WITHOUT NOTICE Installation Instructions for Basics Models BA42WET Please read all instructions prior to installation and keep for future reference! 1. Product should be installed by a qualified electrician. 2. Prior to installation ensure power is off at fuse box to prevent electrical shock. 3. Use only with Class 2 power unit. Utiliser seulement avec Classe 2 unite d'alimentation electrique. 4. Suitable for wet Locations. Convient Aux Emplacements Humides. 5. For under-cabinet or shelf mount. 6. Conforms to UL STD 2108. Certified to CSA STD C22.2 No.250.0. REV0.1 02222024 6 / 7 7777 Merrimac Ave Niles, IL 60714 T 224.333.6033 F 224.757.7557 info@luminii.com www.luminii.com 4 4.1 Place the strain relief in desired place. Make sure it is 3" away from the end of the strip. 4.2 Slide the ziptie through strain relief opening. 4.3 Lay wire lead on top of strain relief. 4.4 Tighten zip tie around lead wire. Cut off excess zip tie. Screw Wire lead LL-ZIP Strain relief Zip tie *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATIONS WITHOUT NOTICE Installation Instructions for Basics Models BA42WET Please read all instructions prior to installation and keep for future reference! 1. Product should be installed by a qualified electrician. 2. Prior to installation ensure power is off at fuse box to prevent electrical shock. 3. Use only with Class 2 power unit. Utiliser seulement avec Classe 2 unite d'alimentation electrique. 4. Suitable for wet Locations. Convient Aux Emplacements Humides. 5. For under-cabinet or shelf mount. 6. Conforms to UL STD 2108. Certified to CSA STD C22.2 No.250.0. REV0.1 02222024 7 / 7 7777 Merrimac Ave Niles, IL 60714 T 224.333.6033 F 224.757.7557 info@luminii.com www.luminii.com 3 RECOMMENDED LAYOUT FOR MULTIPLE ADJACENT RUNS OF LINELED FED WITH SEPARATE POWER SUPPLIES Position power supplies either in the middle of two runs or at the opposite ends. power supply LineLED power supply LineLED power supplies placed in the middle of two adjacent runs power supplies placed at the opposite ends of two adjacent runs 4 Always ensure power to power supply is off! Follow diagrams to connect power feed wires to power supply. Refer to power supply instructions for wiring line voltage side. 24VDC class II power supply PURPLE RED Connect positive wire (plus sign tag or red wire) to RED low voltage wire from power supply. Also, connect negative wire (no tag or black wire) to PURPLE low voltage wire from power supply. OR 120VAC line voltage wires 24VDC low voltage wires power feed wires from LineLED BA connector and 72" wire lead power feed wiring 24VDC class II power supply PURPLE RED Connect positive middle wire (plus sign tag) to RED low voltage wire from power supply. Also, connect BOTH negative wires (no tags) to PURPLE low voltage wire from power supply. 120VAC line voltage wires 24VDC low voltage wires 3-pin connector power feed wiring power feed wires from LineLED *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATIONS WITHOUT NOTICE