Holy Stone HS110/HS200 Drone Instructions for Use

Preface

To make your experience with this drone as straightforward and convenient as possible, please read these instructions before operating and keep them for future reference and maintenance.

Important Statement

This product is a high-precision drone integrating various electronic stability and control mechanisms. It requires careful and correct assembly and setup for safe, accident-free operation. Incorrect or hazardous operation may cause damage to the device or property, or serious injury to those in the vicinity. This product is suitable for experienced drone pilots over 14 years of age. For any difficulties, please contact your local sales agent or Holy Stone customer support.

Safety Guidelines

This flying camera offers easy, controllable flight but carries a risk to property and people if flown irresponsibly or in confined spaces. Incorrect assembly or poor control by inexperienced pilots can result in damage or harm. Be aware of your surroundings and maintain complete control of the vehicle at all times.

• Keep in Distance: Fly in clear locations, away from obstructions like buildings, poles, electrical wires, and trees. Never fly above or near people.
• Adverse Weather Conditions: Avoid moisture, fog, ice, and excessive wind. Fly only in good weather.
• Use and Maintain: Operate legally and according to provided instructions and local laws. Use only original Holy Stone parts for maintenance and repair.
• Do not operate alone: Seek assistance from an experienced pilot when learning. Have others around to help you fly.
• Safety First: Operate within your ability. If ill, disoriented, or unsure, seek help to avoid danger.
• Keep clear of rotating parts: Avoid touching the blades during operation. Ensure foreign objects are kept clear of all moving parts.
• Avoid excessive heat: Keep the device away from heat sources and direct sunlight, as high temperatures can distort the drone's structure.

Warnings

1. Keep these instructions for safe operation and maintenance.
2. You accept responsibility for any injury, loss, or damage resulting from your operation of the device.
3. Always follow instructions when assembling or operating. Maintain at least 2 meters between the user/viewers and the model. Pay attention to the device at all times while flying.
4. Holy Stone and its distributors are not responsible for loss, injury, or damage caused by incorrect operation.
5. This drone is not for children under 14. Younger pilots should operate under adult supervision.
6. Ensure assembly instructions are followed correctly for proper operation and performance.
7. Contains small parts; keep out of reach of children to avoid choking hazards.
8. Do not fly over open water or near public roads to avoid accidents.
9. Keep all packaging materials away from children and dispose of them safely.
10. Internal parts are not user-serviceable. Do not attempt to disassemble or replace parts.
11. Ensure batteries are fitted in the correct orientation.
12. Access the transmitter battery compartment by unscrewing the cover. Insert batteries correctly and secure the cover.
13. Only use the provided charger.
14. The charger is not a toy.
15. Pay close attention to battery polarity when inserting batteries.
16. Use either rechargeable or non-rechargeable "AA" batteries in the transmitter. Do not mix battery types.
17. Use only recommended batteries. Non-rechargeable batteries must not be charged.
18. For rechargeable batteries, follow manual instructions and have adult supervision. Do not leave charging batteries unsupervised. Avoid combustible materials as batteries get hot when charging.
19. Avoid short circuits by fitting batteries incorrectly. Do not crush or squash batteries, as this carries a risk of explosion.
20. Do not mix new and old batteries.
21. Dispose of used batteries properly; do not litter.
22. The power socket must not be removed. Do not attempt to short circuit connections.
23. When disposing of batteries, do not throw them on fires or leave them to decompose. Keep clear of heat sources and high temperatures.
24. If the device will not be used for an extended period, remove batteries to prevent potential damage from leakage.
25. Keep the drone away from sources of magnetic interference to prevent signal issues.
26. Keep clear of rotating parts and beware of loose clothing that could become entangled in the rotors.
27. Be aware of the drone's noise volume and keep your distance to avoid ear damage.
28. The charger socket uses a mini USB 5V connection.
29. Always use the product in compliance with local aviation radio rules and authorities.

Maintenance

1. Clear the product after each use with a clean, soft cloth.
2. Avoid prolonged exposure to direct sunlight and heat buildup on the drone.
3. This device is not waterproof. Do not submerge in water, as this will cause unit failure.
4. Frequently check the charging plug and other accessories for damage. Refrain from flying if any part is damaged until maintenance is performed.

Transmitter Functions

The transmitter can reach a maximum transmission distance of about 400 feet (120 meters) in a wide open area with no radio or electronic interference.

Controls:

• Short Press (Top Button): Take Photo
• Press 2 Seconds (Top Button): Record Video
• Null Button
• Throttle Joystick: Up/Down (Altitude), Turn Left/Right (Yaw)
• Headless/Normal Mode Switch
• Short Press (Bottom Button): Power ON
• Long Press (Bottom Button): Power OFF
• High Speed Switch: "+"
• Low Speed Switch: "-"
• Smart points/Flip Mode (Right Stick): Short press for Flip Mode (short press, then move right control stick in any direction).
• Direction Joystick (Right Stick): Forward/Backward, Left/Right
• Forward/Backward Trimmer
• Left/Right Trimmer
• Short Press (Left Button): A Key Take off / Landing
• Double Click/Long Press (Left Button): Emergency Stop
• Press 2 Seconds (Left Button): RE-SYNC

Transmitter Batteries Installation

Requires 4x 1.5V AA batteries (not included).

Ensure batteries are inserted with the correct polarity.

Drone's Details

The drone consists of the following parts:

• Propeller A
• Propeller B
• Propeller Cap
• Propeller Guard
• Head
• Body Frame
• Front Motor Base
• Motor Shaft
• Motor Base
• Motor Gear (big)
• HD Camera
• Landing Gear
• Drone Battery

Note: All propellers must be installed in the correct orientation. Pay attention to the letters "A" or "B" printed on each propeller during installation.

Charging The Li-Po Battery Of Drone

Balanced charging: Connect the battery to the drone. Insert the USB charging cable into a 5V/0.5-1.0A USB adapter, then connect the cable to the drone's charging port. The indicator light turns red when charging and turns off when fully charged.

Charging time: Approximately 60-90 minutes.

Cautions

• Do not use or charge a battery if it shows signs of swelling, punctures, or damage.
• Allow the battery to cool down in an open, dry area after use before charging to prevent overheating.
• Keep the battery away from furniture, carpet, or flammable materials during charging.
• Do not overload the battery (below 5V/2A). Remove the battery from the charger once charging is complete.
• Be cautious when removing the battery from the charger to avoid damaging the cords, which could lead to a fire or battery damage.

Li-Po Battery Disposal & Recycling: Wasted Lithium-Polymer batteries must not be disposed of with household trash. Please contact your local environmental or waste agency or your nearest Li-Po battery recycling center.

Specification

Drone

• Model: HS110/HS200
• Weight: 146g / 5.13oz
• Max Flight Time: 9 minutes
• WIFI Distance: 30 m (Outdoor And Unobstructed)
• Motor Model: 8616
• Hovering: Enabled
• Operating Temperature Range: 32° to 104°F (0° to 40°C)
• Dimensions: 320 x 320 x 66 mm

CAMERA

• Still Photography Modes: Single Shot
• Video Recording Modes: HD1280x720p
• Max Video Bitrate: 25 Mbps
• Photo Format: JPEG
• Video Format: AVI
• Supported TF Cards: TF Card 4 GB included
• Operating Temperature Range: 32° to 104°F (0° to 40°C)

APP/LIVE VIEW

• Mobile App: Deerc FPV
• Live View Working Frequency: 2.4 GHz ISM
• Live View Quality: 720P @ 20fps
• Latency: Low Latency Video (depends on conditions and mobile device)
• Required Operating Systems: iOS 8.0 or above / Android 4.1.2 or above
• Recommended Devices: 4.7" to 6.0" Smartphones

TRANSMITTER

• Operating Frequency: 2.4 GHz
• Transmission Distance: 50-100 m (outdoors and unobstructed)
• Operating Temperature Range: 32° to 104°F (0° to 40°C)
• Battery: 4×1.5 V Alkaline batteries AA
• Mobile Device Holder: Smartphones

FLIGHT BATTERY

• Capacity: 650mAh
• Voltage: 3.7 V
• Battery Type: LiPo
• Energy: 2.405Wh
• Net Weight: 30 g / 1 oz
• Charging Temperature Range: 41° to 104°F (5° to 40°C)
• Charging Time: 60~90 mins

USB CHARGING CABLE

• Voltage: 5 V
• Rated Power: ≤10 W

Flight

Safety Precautions:

• Rotating propellers can be dangerous. Do not start motors when people are nearby.
• Always keep hands on the transmitter as long as the motor is spinning.
• Only stop motors mid-flight in emergency situations to reduce risk of damage or injury.

Flight Steps:

1. Power on the transmitter.
2. Power on the drone.
3. Place the drone on a level surface. The LED indicators on the drone will flash.
4. Push the left joystick up then down to pair the drone and transmitter. A beep from the transmitter and steady LED lights on both devices indicate successful pairing.
5. Calibrate the gyro: Long press the One Key Return Function button.
6. Take Off: Press ONE KEY TAKE OFF. The drone will fly up and hover about 1.5 meters.
7. Landing: Press ONE KEY LANDING for a slow, automatic landing.
8. Manual Landing: Push the left joystick down slowly until the drone touches the ground. Hold for a few seconds to stop the motors.
9. Altitude and Yaw Control (Left Stick): Push the left joystick up/down to ascend/descend, or left/right to rotate.
10. Forward/Backward/Left/Right Control (Right Stick): Push the right joystick up/down/left/right to move the drone forward/backward/left/right.
11. L/R Sideward Fly Trim: If the drone drifts left or right, slide the trim button to the opposite direction to re-balance.
12. F/B Sideward Fly Trim: If the drone drifts forward or backward, slide the trim button to the opposite direction to re-balance.
13. Emergency Stop: Long press or double click the Emergency Stop button to immediately stop the motors.

Headless Mode

Note: Do not use Headless Mode until you fully understand the instructions. Insufficient experience may lead to loss or damage.

1. Place the drone in front of the pilot before pairing. Ensure the drone's head faces the same direction as the pilot, and the tail faces the pilot.
2. Push the left joystick up then down to pair the transmitter to the drone.
3. Press the Headless Mode button on the transmitter to enter Headless Mode.

Direction of Control in Headless Mode: The forward direction is the direction the pilot faces when pairing. Pushing the direction joystick forward moves the drone away from you; backward moves it towards you. Moving the right stick left or right moves the drone left or right relative to you. It is crucial that the pilot does not change position or facing direction to avoid confusion.

4. Press the Headless Mode button again to exit Headless Mode.

One Key Return

The drone has a One Key Return function that makes it fly back to the pilot automatically when the button is pressed. It continues until the mode is canceled or the pilot resumes control.

• In Normal Mode (LED light "NORMAL" is on): Press the One Key Return button. The drone flies back to the direction the tail was pointing when paired.
• In Headless Mode (LED light "HEADLESS MODE" is lit): Press the One Key Return button. The drone flies back to the direction the tail was pointing when Headless Mode was entered.

Note: Use Headless Mode and One Key Return functions only after fully comprehending them to avoid loss of control or damage.

Wi-Fi Camera Function

This drone is equipped with an FPV real-time camera and gravity sensor control. Download the “Deerc FPV” App to use these functions.

Scan the QR codes to download the app for Apple iOS or Android systems.

(Install the phone holder)

First Person View Function

Power on the drone, go to phone settings, select Wi-Fi, and connect to "HolyStoneFPV***" for camera connection. Open the “Deerc FPV” App to see real-time images from the camera.

• Take Photo: Click the "" icon.
• Record Video: Click the "" icon to record, and click again to save.

All images and videos are saved on the phone and in the TF card. To view them on a computer, insert the TF card into a card reader and connect to a computer's USB outlet. Images can also be viewed in the App.

Tip: For more details, click the "" icon on the App interface.

Spare Parts (Sold Separately)

• Propellers (A & B)
• Landing Gear
• Propeller Guard
• USB Charging Cable
• Motor
• Motor Gear
• Card Reader
• Phone Holder

Trouble Shooting

Please do not hesitate to contact Holy Stone support if you need further assistance.

Support Contacts:

• usa@holystone.com (USA)
• ca@holystone.com (Canada)
• eu@holystone.com (Europe)
• jp@holystone.com (Japan)
• +1 (855) 888-6699

General Information

FCC Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If interference occurs, try reorienting or relocating the receiving antenna, increasing separation between equipment and receiver, connecting to a different circuit, or consulting a dealer or technician.

WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

RF Exposure

The equipment complies with FCC radiation exposure limits for an uncontrolled environment. Install and operate with a minimum distance of 20cm between the radiator and your body.

IC Notice

This device complies with Canada Industry licence-exempt RSS standard(s). Operation is subject to two conditions: (1) this device may not cause interference; and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

CAN ICES-3 (B) / NMB-3 (B)

RF Exposure

Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. Install and operate with a minimum distance of 20cm between the radiator and your body.

Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

HOW TO RECYCLE THIS PRODUCT

The symbol on the product or documentation indicates it must not be disposed of with household waste. Uncontrolled waste disposal may harm the environment or human health. Please separate your device from other waste types to recycle it responsibly to foster sustainable re-use of material resources.

Battery Warning

• Failure to follow instructions may result in serious injury, irreparable damage to the battery, fire, smoke, or explosion.
• Always check the battery's condition before charging or using.
• Replace the battery if dropped, or if it shows odor, overheating, discoloration, deformation, or leakage.
• Only use the approved LiPo charger or a balancing charger for LiPo cells. Do not use any other charger.
• The battery temperature must not exceed 60°C (140°F), or it could be damaged or ignite.
• Never charge on a flammable surface, near flammable products, or inside a vehicle. Place the battery in a non-flammable, non-conductive container.
• Never leave the battery unattended during charging.
• Do not disassemble, modify wiring, or puncture cells. Ensure the charger output voltage corresponds to the battery voltage. Do not short-circuit batteries.
• Never expose the LiPo battery to moisture or direct sunlight, or store it in places where temperatures could exceed 60°C (e.g., a car in the sun).
• Always keep batteries out of reach of children.
• Improper battery use may result in fire, explosion, or other hazards.
• Non-rechargeable batteries are not to be recharged. Rechargeable batteries should only be charged under adult supervision.
• Do not mix different types of batteries or new and used batteries.
• Batteries are to be inserted with the correct polarity.
• Supply terminals are not to be short-circuited. Regularly examine the transformer or battery charger for damage to cords, plugs, enclosures, or other parts. Do not use if damaged.
• Keep packaging as it contains important information.
• The toy is only to be connected to Class II equipment bearing the symbol.

Caution

• Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to instructions.
• The maximum operating temperature of the EUT is 45°C and should not be lower than -10°C.
• The device complies with RF specifications when used at 0mm from your body.

Declaration of Conformity

Xiamen Huoshiquan Import & Export CO., LTD declares that the essential requirements and other relevant provisions of Directive 2014/53/EU, RoHS Directive 2011/65/EU, and Safety Directive 2009/48/EC have been fulfilled for the product.

Product Name: Remote control four axis series

Model: HS110/HS200

The Statement of compliance is available at: http://www.holystone.com/Download/CE/HS110_HS200_EU_DOC.pdf

This product can be used across EU member states.

MANUFACTURER INFORMATION

Manufactured by: Xiamen Huoshiquan Import & Export CO., LTD

Room 703, No. 813-2 Xiahe Road, Siming District, XIAMEN, China

TEL: +1 (855) 888-6699

Made in China