Technical Documents - FS.comReturn Policy - FS.comProducts Warranty - FS.com
User Guide for QSFPTEK models including: S5300-24P4TS 24 Port Gigabit Ethernet L2 PoE Switch, S5300-24P4TS, 24 Port Gigabit Ethernet L2 PoE Switch, Ethernet L2 PoE Switch, L2 PoE Switch, PoE Switch
S5300-24P4TS 24-Port Gigabit Ethernet L2 PoE Switch, 24x 10/100/1000BASE-T RJ45 PoE ports with 4x 1G RJ45/SFP Combo Ports - QSFPTEK
File Info : application/pdf, 11 Pages, 521.22KB
DocumentDocumentS5300-24P4TS Quick Start Guide
24-Port Gigabit Ethernet L2+ PoE+ Switch 24x 10/100/1000BASE-T RJ45 PoE ports, with 4x 1G RJ45/SFP Combo Ports, 370W
V1.0
www.qsfptek.com
V1.0
1 11
Introduction
The S5300-24P4TS is a RJ45 PoE switch. Product positioning is to meet the requirements of complex scenarios such as operator IP metropolitan area network, small and medium-sized enterprise network, campus network, enterprise network and other networks. We appreciate your decision to select S5300-24P4TS. This manual is intended to help you become acquainted with the switch design and provide instructions for implementing the switches into your network.
S5300-24P4TS
Accessories
www.qsfptek.com
V1.0
2 11
Hardware Overview
Front Panel Ports
SFP
S5300-24P4TS
RJ45
RJ45 SFP
Console
Ports
RJ45 SFP CLI port
Description
1000BASE-T ports for Ethernet connection and supports up to 30W PoE+ Hot-swappable SFP ports for 1G connection An RJ45 console port for serial management
www.qsfptek.com
V1.0
3 11
Front Panel LEDs
S5300-24P4TS
RJ45
RJ45 SFP
Console
Abbrev. Name
Description
PWR
Power indicator If the switch is powered on, the indicator is on.
SYS
System indicator If the switch is started, the system indicator flickers.
1-24
Link/Act indicator on each port
Always on in orange: 10/100M Always on in green: 1000M Off: no signal transmission
25S-28S
Link/Act indicator on SFP port
Always on in green: 1000M Off: no signal transmission
Reset
Reset
Keep the device powered on, press the button "Reset" for 6s, and the system will return to the default setting.
RJ45 Gigabit TX port 1-24 24 gigabit TX ports
CLI SFP 25T-28T
Console port
Gigabit optical port 25S-28S
Link/Act indicator on RJ45 port
It can be used to connect a computer or a terminal for monitoring and configuring the switch.
4 SFP interfaces
Always on in green: 1000M Off: no signal transmission
www.qsfptek.com
V1.0
4 11
Back Panel
S5300-24P4TS
AC Power
Grounding Point
Installation Requirements
Before you begin the installation, make sure that you have the following:
Phillips screwdriver. Standard-sized, 19" wide rack with a minimum of 1U height available. Category 5e or higher RJ45 Ethernet cables for connecting the network devices.
Site Environment:
Make sure that the workshop is well-ventilated, the heat of electrical devices is well-discharged and sufficient air circulation is provided for device cooling. Avoid damage devices by following the electrostatic discharge prevention procedure. Put the machine box in a place where cool air can blow off the heat inside the machine box. Make sure the machine box is sealed because the opened machine box will reverse the cool airflow.
www.qsfptek.com
V1.0
5 11
Mounting the switch
Connecting the Power
1. Plug the AC power cord into the power port on the back of the switch. 2. Connect the other end of the power cord to an AC power source.
Connecting the RJ45 Port
1. Plug a compatible RJ45 transceiver into the RJ45 port. 2. Connect an Ethernet patch cable to the RJ45 transceiver. Then
connect the other end of the cable to another RJ45 device.
www.qsfptek.com
V1.0
6 11
Connecting the SFP Port
1. Connect SFP modules through the fiber to other Ethernet terminal devices. 2. Connect the other end of the cable to the SFP port on the front of the switch.
Connecting the Management Port
Connecting the Console Port
1. Insert the RJ45 connector of the console cable into the RJ45 console port on the front of the switch. 2. Connect the other end of the console cable to the RS-232 serial port on the computer.
3. The console port of S5300-24P4TS does not support traffic control. Therefore, you must set the option data traffic control to none when you configure the switch with the super terminal. Otherwise, the singlepass problem will arise on the super terminal.
www.qsfptek.com
V1.0
7 11
Configuring the Switch
Configuring the Switch Using the Web-based Interface
Step1: Connect the computer to the Management port of the switch using the network cable. Step 2: Set the IP address of the computer to 192.168.0.x. ("x" is any number from 2 to 254.). Set thesubnet mask of the computer to 255.255.255.0.
www.qsfptek.com
V1.0
8 11
Step 3: Open a browser, type http://192.168.0.2, and enter the default username and password, admin/ admin. Step 4: Click sign in to display the web-based configuration page.
Configuring the Switch Using the Console Port
Step 1: Connect a computer to the switch's console port using the supplied console cable. Step 2: Start the terminal simulation software such as HyperTerminal on the computer. Step 3: Set the parameters of the HyperTerminal: 9600 bits per second, 8 data bits, no parity, 1 stopbit and no flow control.
Step 4: Enter the default username and password, admin/admin.
www.qsfptek.com
V1.0
9 11
Troubleshooting
Loading Failure Troubleshooting
When encountering loading failures, the system may continue running in its original version. To address this issue, users should first verify the physical port connections. In case of disconnected ports, reconnect them to ensure proper physical connections and proceed with reloading. If the physical connections are correct, users should then review the loading process information displayed on the super terminal for input errors. Any identified input errors should be corrected before reloading the system.
User Password Lost Troubleshooting
If a user forgets or loses the system password, they can reset it using the following method: 1. Connect your computer to the switch's console port using a console cable. 2. Press the "ctrl + b" keys to enter the Uboot mode. 3. Start the system with an empty configuration file that has no password by entering the following command: Bootrom#boot_flash_nopass Bootrom#Do you want to revert to the default config file?[Y|N|E]:
username and password.
Configuration System Troubleshooting
1. Confirm that the power supply is functioning properly and that the console cable is securely connected. 2. Verify that the console cable is the correct type for your system. 3. Check if the control cable driver is correctly installed on the computer. You may need to download and
install the appropriate driver from the manufacturer's website. 4. Confirm that the HyperTerminal parameters are correctly set. Ensure that the baud rate, data bits, stop bits,
and parity are properly configured according to your system's specifications.
www.qsfptek.com
V1.0
10 11
Support and Other Resources
Contct us
https://www.qsfptek.com/company/contact-us.html
Email
sales@qsfptek.com
Customer Success https://www.qsfptek.com/resources/customer-success-stories
Product Warranty
S5300 series switches are backed by a 5-year limited warranty supported by QSFPTEK. And you are eligible to apply for a return or exchange of your items within 14 days of receiving them.
For more details about applying qualifications, please live chat or email sales@qsfptek.com for support.
5 Year Warranty
14-day Return Window
www.qsfptek.com
V1.0
11 11