Instruction Manual for SENECA models including: R-KEY-LT Gateway EtherNet IP, R-KEY-LT, Gateway EtherNet IP, EtherNet IP
R-KEY-LT-E | Gateway EtherNet IP | SENECA
File Info : application/pdf, 4 Pages, 170.71KB
DocumentDocumentINSTALLATION MANUAL R-KEY-LT R-KEY-LT-P R-KEY-LT-E PRELIMINARY WARNINGS The word WARNING preceded by the symbol indicates conditions or actions that put the user's safety at risk. The word ATTENTION preceded by the symbol indicates conditions or actions that might damage the instrument or the connected equipment. The warranty shall become null and void in the event of improper use or tampering with the module or devices supplied by the manufacturer as necessary for its correct operation, and if the instructions contained in this manual are not followed. WARNING: The full content of this manual must be read before any operation. The module must only be used by qualified electricians. Specific documentation is available via QR-CODE shown on page 1. The module must be repaired and damaged parts replaced by the Manufacturer. The product is sensitive to electrostatic discharges. Take appropriate measures during any operation. Electrical and electronic waste disposal (applicable in the European Union and other countries with recycling). The symbol on the product or its packaging shows the product must be surrendered to a collection centre authorized to recycle electrical and electronic waste. DOCUMENTATION R-KEY-LT DOCUMENTATION R-KEY-LT-P DOCUMENTATION R-KEY-LT-E SENECA s.r.l.; Via Austria, 26 35127 PADOVA ITALY; Tel. +39.049.8705359 - Fax +39.049.8706287 CONTACT INFORMATION Technical support support@seneca.it Product information sales@seneca.it This document is the property of SENECA srl. Copies and reproduction are prohibited unless authorised. The content of this document corresponds to the described products and technologies. Stated data may be modified or supplemented for technical and/or sales purposes. MI00472-6-EN INSTALLATION MANUAL 1/4 MODULE LAYOUT 110mm 53mm 32mm Weight: 80g; Enclosure: UL94-V0 self-extinguishing PC/ABS material, black. SIGNALS VIA LED ON FRONT PANEL LED PWR TX RX ETH ACT (Yellow) ETH LNK (Green) COM (R-KEY-LT-P and R-KEY-LT-E version) COM+PWR (R-KEY-LT-P version) STATUS On Flashing Flashing Flashing Flashing Flashing Flashing Off Flashing LED meaning The device is powered with assigned IP IP not assigned Data transmission on port RS232/RS485 Data receipt on port RS232/RS485 Packet transit on Ethernet port Ethernet port connected Profinet or Ethernet/IP communication active No Profinet or Ethernet/IP communication Webserver active / Profinet not active DEVICE CONFIGURATION The device can be fully set up via integrated web server. The product programming and/or configuration tools, as well as all the manuals, can be downloaded using the QR-CODE from the web address: For further information, refer to the USER MANUAL. FACTORY IP ADDRESS The default module IP address is static: 192.168.90.101 PROFINET AND WEBSERVER MODE The device is normally in Profinet mode; in Profinet mode the device can be configured only through the Easy Setup2 software. In order to access the internal webserver it is necessary to put the device in Webserver mode using the Easy Setup2 or Seneca Device Discovery software. it is also possible to change the operating mode by pressing the side button PS1 following the procedure given in the user manual. MI00472-6-EN INSTALLATION MANUAL 2/4 WEB SERVER To access the maintenance Web Server with the factory IP address above, use the following credentials: Username: admin; Password: admin N.B.: For the R-KEY-LT-P version it is first necessary to activate webserver mode CAUTION DO NOT USE DEVICES WITH THE SAME IP ADDRESS IN THE SAME ETHERNET NETWORK. TECHNICAL SPECIFICATIONS CERTIFICATIONS INSULATION POWER SUPPLY ENVIRONMENTAL CONDITIONS ASSEMBLY CPU OPERATING SYSTEM CONFIGURATION CONNECTIONS COMMUNICATION ETHERNET PORTS RS232/485 ETH PWR 1500 Vac Voltage: 11 ÷ 40Vdc; 19 ÷ 28Vac; 50 ÷ 60 Hz, max absorption: 1W Temperature: -25°C ÷ +65°C Humidity: 30% ÷ 90% non condensing Storage temperature: -30°C ÷ + 85°C Protection rating: IP20 (not rated by UL) DIN rail 35mm IEC EN60715, wall or panel with screws. ARM 32 bit Real time multitasking Configuration and FW update via webserver; Via DIP - SWITCH Via EASY SETUP 2 configuration software Removable 7-way screw terminals, 5 mm pitch, cable section up to 2.5 mm2 Removable 2-way screw terminals, 5 mm pitch, cable section up to 2.5 mm2 RJ45 connector for Ethernet cable RS232/RS485 on 1-7 terminal; maximum Baud rate 115k 1 x 100Mbit Ethernet port with auto switch MI00472-6-EN INSTALLATION MANUAL 3/4 DIP - SWITCH SETTINGS WARNING The DIP-switch settings are read only at boot time. At each change, perform a restart. SW1 DIP-SWITCH: Through DIP-SWITCH-SW1 it is possible to set the polarization of the bus relative to the RS485 port: DESCRIPTION DIP 1 DIP 2 To polarize the bus on RS485, both SW1 DIP switch selectors must be set to ON NOT to polarize the bus on RS485, both SW1 DIP switch selectors must be set to OFF SW2 DIP-SWITCH: Through DIP-SWITCH-SW2 it is possible to set the IP configuration of the device: DESCRIPTION DIP 1 To obtain the configuration from the Flash memory, both SW2 DIP switch selectors must be set to OFF To reset the device to factory settings both SW2 DIP switches must be set to ON To force the device's IP address to the standard value of SENECA Ethernet products: 192.168.90.101 DIP 2 Reserved ELECTRICAL CONNECTIONS CAUTION Switch the module off before connecting inputs and outputs. To meet the electromagnetic immunity requirements: - use shielded signal cables; - connect the shield to a preferential instrumentation earth system; - separate shielded cables from other cables used for power installations (transformers, inverters, motors, etc...). CAUTION Use only copper or copper-coated aluminium or AL-CU or CU-AL conductors POWER SUPPLY RS485 SERIAL PORT RS232 SERIAL PORT Vac / Vdc 8 Vac / Vdc 9 The power supply source must be protected from any module malfunctions using appropriately-sized safety fuses. A (+) 1 B (-) 2 GND 3 GND 3 RTS 4 Tx 5 CTS 6 Rx 7 CAUTION The device can only be powered by a power supply with a limited energy circuit 40Vdc / 28Vac max in output according to CAN/CSA-C22.2 No.61010-1-12 / UL Std.No.61010-1 (3rd Edition) chapter 6.3.1/6.3.2 and 9.4 or class 2 according to CSA 223/UL1310. CAUTION These are open type devices intended for installation in a final casing/panel that offers mechanical protection and protection against the spread of fire. MI00472-6-EN INSTALLATION MANUAL 4/4