GGM Gastro International GmbHGGM Gastro International GmbH
User Manual for ggm gastro models including: WAEBJ1, WAEBJ2, WAEBJ1 Waffle Maker, Waffle Maker
2. Please check if all switches are in off position. 3. Please check all the accessories are complete. 4. Please tear up the protective film on the surface of the product, then clean the rust oil
WAFFLE MAKER. USER'S MANUAL. Page 2. Thank you for buying our product, in order to ensure safe used, please read the. Instructions before using and keep it ...
USER’S MANUAL . Thank you for buying our product, in order to ensure safe used, please read the Instructions before using and keep it for reference. Safety Precautions The following safety precautions must be observed when using this product: 1. Please read the relevant instructions carefully before using this product.
File Info : application/pdf, 9 Pages, 1.06MB
DocumentDocumentWAFFLE MAKER USER'S MANUAL Thank you for buying our product, in order to ensure safe used, please read the Instructions before using and keep it for reference. Model WAEBJ1 WAEBJ2 Dimensions(mm) 440*305*225 630*420*225 Voltagev Power w 230 2000 230 2000+2000 Hz 50-60 50-60 Safety Precautions The following safety precautions must be observed when using this product: 1. Please read the relevant instructions carefully before using this product. 2. Do not share the same power source with other high-power appliances to avoid excessive power load and other dangers. 3. The surface temperature of this product is very hot after working or just using. Burns may be caused by contact with hot parts. 4. If children are nearby, use the product with extra care. Do not leave the product to children alone. 5. Do not allow this product to be used unattended. 6. Do not touch the power cord with sharp objects and high-temperature surface to avoid damage to the power cord. 7. Frequently check whether the power cord and plug are damaged. Once any signs of damage are found, please stop using immediately and ask for professional maintenance or replacement. 8. After use, press the power button to close and pull out the plug from the socket to avoid leakage or shock due to aging insulation 9. The product shall be installed in a dry, clean and ventilated place; And put the product in a horizontal and smooth position 10. For the sake of safety, the product must be reliable grounding, and install leakage switch to ensure personal safety, otherwise not to use. 11. Please unplug the power cord and remove, check or clean the product after it has cooled completely. 12. Do not plug or unplug the power cord in wet hands to avoid electric shock. Note for the First Time Use 1. Please read the Instructions carefully. 2. Please check if all switches are in off position. 3. Please check all the accessories are complete. 4. Please tear up the protective film on the surface of the product, then clean the rust oil wipe on surface of the product with a dry cloth. 5. The supply voltage must match the voltage specified on this machine. 6. The smoke is normal when first time turn on the machine, it's the oil inside the machine which to protect it become rusting. Operating Steps 1.Mix the ingredients. 2.Turn on the switch , adjust the Temperature to 160-180. 3. 3.Wait for the indicator light to go out. 4.Put the pulp to the non-stick plate. 5.Turn the machine and adjust the timer to 3 minutes. Care and Cleaning 6.Turn on the machine and take out the waffle. 1. Unplug the power cable and ensure that the product is cooled completely, then cleaning and collection. 2. Cleaning cooking surface with a soft cloth or sponge dampened in a mild detergent. 3. Please don't use wire brush, stiff brush or other corrosive liquids to clean it, avoiding damage the surface coating. 4. If batter adheres to plates, simply pour a little cooking oil onto the baked batter and let stand approximately 5 minutes, allowing batter to soften for easy removal. 5. Never use an abrasive cleanser or harsh pad. 6. Never clean the product by sprinkling water and immersed in water. Tips and Maintenance 1. Pan MUST be open when pre-heating (if closed the temperature inside is much more higher than open, long time high temperature is not good for Teflon coating), 160-180 is our best temperature during the test. 2. If machine is an additional product to your shop, please keep temperature under 80 when no customers, it's better to turn off the machine if there's long time no customer. 3. If machine is main product in your shop, 3-4 units machine is suggested, they can be replaced every two hours. 4. Use bamboo stick to take out cone, do not use any metal tool. If there's black dots appear on the pan surface, it can be judged that the caramel with Teflon coating is falling off (Caramel is when oil and sugar do not clean for a long time, it cannot be seen by visual inspection, it turns into black dots and stick on waffles) The best solution is changing heating pan. 5. Use wet towel to clean the pan, if anything difficult to wipe off, use professional kitchen glue brush, put some water in holes, heat the water a bit, it's easier cleaning, but do not let water go inside of machine. 6. Do not brush oil on pan directly, you can add oil inside your recipe or waffle mix, but do not add too much oil, or it will get infiltrate and heater may get burnt. 7. Do not use corrosive cleanser to clean the waffle pan. This machine shell must be grounded and ensure safety, thank you for your cooperation. Notice The products which electric power is over 1kw must plug a properly (grounded) individual receptacle. Do not cover the product with a cloth or plastic bag while you are using it. Ensure to unplug the product while you don't use it. Do not touch the product with wet hands. Never clean the machine by sprinkling water. Do not use the product outside in the rain or wet area. Use the product in a light place. Do not use the product near flammable gas or Do not use the It could result in fire by ignition. It could result in fire. It could result in fire or electric shock. It could result in electric shock. It could result in electric shock or product damage. It could result in electric shock. It could result in accident or burn if you use it in a dark room. It could result in explosion or fire. Fault Reason Method 1.There is no power at the outlet Turn on the powerbut the green light 2.The power cord contacts bad doesn't work terminal is loose 3.The green light was burnt out 1.Check the socket for power 2Fastening the power cord and terminals wiring 3.Replace the green light The yellow light didn't go out and the temperature of the machine rose is 1.The thermostat doesn't work 1.Replace the thermostat out of control The indicator light is not on, but the temperature control is normal 1.The indicator light has bad contact 2.The indicator light was burnt out 1.Fastening the wires 2.Replace the indicator light 1.Wrong connection of indicator 1.Rewire according to correct The yellow light is on but not heated light wiring 2.The heating tube was burnt out; 2.Replace the heating tube The green light is on, the yellow light is Thermostat was damaged off, but the machine is not heated Replace the thermostat Yellow indicator light is always on, the 1.The connection of lower board lower plate is not hot, the upper plate heating pipes is loose has been heating and the temperature 2.The lower heating tube is is ultra high damaged The yellow light is on and the temperature of the lower plate is normalbut the upper plate is not hot. 1.The connection of upper heating pipes is loose 2.The top heating tube is burnt out 1.The internal wiring is loose and Plug in the power and turn on the thermostatthen caused switch trip the belt parts touch the metal shell; 2.Short circuit is caused by heating pipe burning 1.Check the connection of heating pipes 2.Replace the lower heating tube 1.Check the connection of heating wires 2.Replace the lower heating tube 1.Check the internal wiring of the machine and tighten it 2.Replace with a new heating tube Inspection of general faults WAEBJ1 No. Material no 1 2 3 4 3050035 5 3040012 6 3080195 7 3040030 8 9 3030002 10 11 3040041 12 13 3020031 14 3020070 15 3020053 16 3020037 17 3020002 18 3091248 19 3040001 20 3040025 21 3050035 22 3070383 23 3070383 24 3080380 Spare parts name Up cover Handle fixed board Element press board Up element Connect terminal Flexible tube Wire clip Down cover Wire Base Foot Bottom sealing board 5 minute timer Timer knob Thermostat knob 300 dial 300 thermostat Support column Switch Light Down element Down molding board Up molding board Handle WAEBJ2 No. Material no 1 2 3 4 3050035 5 3040012 6 3080195 7 3040030 8 3030002 9 3040041 10 11 3040001 12 3040025 13 3020002 14 3020037 15 3020053 16 3020070 17 3020031 18 3050035 19 20 3091248 21 22 3070383 23 3070383 24 3080380 Spare parts name Up cover Handle fixed board Element press board Up element Connect terminal Flexible tube Wire clip Wire Foot Bottom board Switch Light Thermostat 300 dial Thermostat knob Timer knob 5 minute timer Down element Base Support column Down cover Down molding board Up molding board Handle GGM Gastro International GmbH Weinerpark 16, 48607 Ochtrup www.ggmgastro.com