User Guide for OTTO models including: Wired 6 Motorized Roller Shades, Motorized Roller Shades, Roller Shades, Shades
2024-02-01 — Remote Control Functions & Battery Replacement. Remove cover from base by ... Consult user manual for your controller for information on selecting channel ...
MOTORIZED ROLLER SHADES OTTO WIRED 6 PROGRAMMING GUIDE REMOTE CONTROL BASICS Wall Mount Holder Remove cover from base by prying with flat head screwdriver. Use supplied fasteners and anchors to attach the base to wall. Replace cover by pressing snap latches into place. Remote Control Functions & Battery Replacement LEVEL CONTROL UP STOP DOWN CHANNEL Remove cover from remote press gently in and down to disengage cover. SETTING (P2) Install battery with positive (+) side facing up. Slide to remove. Remote Battery 3V CR2450 Cover 1 WIRING Power Options Cut off the mains power supply Connect the motor according to the information in the table below. 3 x 1,5 mm2 1 2 3 3 x 0.75 mm2 Range 220-240V 100-120V Neutral Blue White Live Brown Black Earth Yellow / Green Green Ensure cable is kept clear of fabric. Ensure antenna is kept straight and away from metal objects. 2 Motor state test This table describes the function of a short P1 button press/release (<2 seconds) depending on current motor configuration. P1 Press Condition Function Achieved Visual Feedback Audible Function Described Feedback Short Press If limit is NOT set If limits are set None Operational control of motor, run to limit. Stop if running No Action Motor runs If motor is in "Sleep Mode" & limits are set Wake and control Motor wakes and runs in a direction None None None No Action Operational control of motor after pairing and limit setting is completed first time Motor is restored from Sleep Mode and RF control is active Motor configuration options The P1 Button is utilized to administer motor configuration as described below and beginning in Section Activate Pairing Mode Approx. Hold P1 P1 Motor Response Sleep Mode Approx. Motor Response Reverse Direction Motor Response Approx. NOTE Reverse motor direction from P1 button only when motor does not have any limits. Reset To Factory Settings Motor Response Approx. 3 Pair motor with controller Select channel on controller. Hold P1 button on motor head. Hold STOP on controller. IMPORTANT Consult user manual for your controller for information on selecting channel. Motor Response Motor Response Motor is now in step mode and ready for setting limits Check motor direction To check travel direction of shade, press UP or DOWN on controller. To reverse shade direction, hold both UP and DOW. N Until the motor responds. Quick Press = Step Long Press = Continuous Travel Motor Response IMPORANT Damage to shade may occur when operating motor prior to setting limits. Attention should be given. IMPORTANT Reversing motor direction using this method is only possible during initial set-up. 4 Setting Limits Move shade to the desired highest or lowest position by pressing theUP or DOWNbuttons on controller. To save upper limit, hold UP and STOP. To save lower limit, hold DOWN and STOP. IMPORTANT Cycle shade up and down prior to setting limits to settle fabric Motor Response 5 SEC S Initial set-up is now complete IMPORTANT After setting limits, motor will automatically exit from initial set-up mode. 5 ADJUSTING LIMITS Adjust upper limit Hold UP and STOP on controller. Move shade to the desired highest position by pressing the UP button. To save upper limit, hold UP and STOP. Motor Response 5 SEC S 5.2 Adjust lower limit Hold DOWNand STOP on controller. Move shade to the desired lowest position by pressing the DOWN button. Motor Response 5 SEC S To save lower limit, hold DOWNand STOP. Motor Response 5 SEC S Motor Response 5 SEC S 6 ADDING OR REMOVING CONTROLLERS AND CHANNELS Using motor P1 button Hold P1 button on motor head. Hold STOP on controller to add or remove. Motor Response Motor Response Using a pre-existing controller Press P2 on existing controller. Press P2 on existing controller. Press P2 on new controller. Motor Response Motor Response IMPORTANT Consult user manual for your controller or sensor. Motor Response 7 FAVORITE POSITIONING Set favorite position Move shade to the desired position by pressing the UP or DOWN button on the controller. Press P2 on controller. Press STOP on controller. Press STOP on controller. Motor Response Motor Response Motor Response Send shade to favorite position Hold STOP on controller. Delete favorite position Press P2 on controller. Approx. Press STOP on controller. Press STOP on controller. Motor Response Motor Response Motor Response 8 ROLLER MODE Enter roller mode (Default) Hold UP and DOWNon controller. Press STOP. Motor Response 5 SEC S Motor Response SLEEP MODE Enter Sleep Mode Sleep mode is utilized to prevent a motor from moving during shipping of a fabricated shade Hold P1 button on the motor head Motor Response Exit Sleep Mode Exit sleep mode once the shade is installed Press and release P1 button on the motor head Motor Response 9 TROUBLESHOOTING Problem Motor is not responding Unable to adjust or set limits. Cannot program a single Motor (multiple motors respond) Cause Remedy A / C power supply not plugged in. Check motor to connection and power cable AC plug. Battery in wand are depleted Replace 8xAA alkaline batteries. Power failure Check power supply to motor is connected and active Transmitter battery is discharged Replace battery Battery is inserted incorrectly into transmitter Check battery polarity Radio interference/shielding Ensure transmitter is positioned away from metal objects and the aerial on motor or receiver is kept straight and away from metal Receiver distance is too far from Move transmitter to a closer transmitter position Incorrect wiring Check that wiring is connected correctly (refer to motor installation instructions) Remote is in a locked state. Change remote status to an unlocked state Always reserve an individual channel for programming functions Multiple motors are paired to the same channel. SYSTEM BEST PRACTICE - Provide an extra 15 channel remote in your multi motor projects, that provides individual control for each motor for programming purposes Place all other motors into sleep mode. ! WARNING Cords on window covering products present a potential strangulation hazard. For child safety, consider cordless alternatives or products with inaccessible cords. ! ADVERTENCIA Las cuerdas y cadenas y persianas presentan un peligro de estrangulacion. Para la seguridad de los ninos, considere alternativas sin cuerdas o productos con cuerdas y cadenas inaccesibles. 10Adobe Illustrator CC 22.0 (Macintosh) Adobe PDF library 15.00