User Guide for Reelight models including: GEM Front Light Led USB Front Light Clear, GEM Front, Light Led USB Front Light Clear, USB Front Light Clear, Front Light Clear, Light Clear, Clear
GEM – Reelight | Help Center
GEM | User Manuals – Reelight
GEM+ Front Light User GuideEnglish Read all the instructions carefully before first use. CAUTION Do not look directly at the strobe or LED lights when operating. Pay attention and care when recovering the USB seal to ensure correct seal so water ingress does not occur. No liability can be accepted for any damage caused by non-compliance with these instructions or any other improper use or mishandling. The device has a Lithium-Ion battery. When disposing of this, it should be done in compliance with the rules and regulations in your country of residence. Mounting the bracket To keep the lights fastened and secure, the rubber rings are provided in 3 different sizes to provide a snugly wrap around a variety of handlebars and head tubes. Start by picking one of the three rubber rings best suited for the size of the handlebars or head tube. 1 1. Insert one end of the ring into the groove of the bracket 2 2. Locate the grey rubber pad from the top bracket and (remove the small screw first if mount the bracket on top of it comes pre-installed). Position the base part. Insert the screw the bracket on top of the with the small O-ring and handlebar or head tube. Pull the tighten it using the included other end of the ring around the Allen key. bar and insert it into the other groove. Use the smallest ring possible as this will ensure a more stable mount. 3 3. Insert the grey rubber pad into the top bracket. 4 4. Insert the light into the bracket by pushing down as illustrated. 5 5. Check that the light is securely mounted into the bracket. 6 6. Turn on the light by pressing the button down for 2 seconds. Using the light Please note: When the light is powered on for the first 1 time, the light will be in constant light mode as a factory default. When the light is turned on again, the last used setting will be activated. 1. To power on the light: press the button for 2 seconds. To power off the light: hold the button for 2 seconds. 2 2. Press the button to cycle between the different modes: High / Medium / Medium + Flash / Pulse/ Strobe / Eco-flash Eco mode When the battery charge goes below 10% (charge indicator will flash orange), you can only switch between Constant Mid and Echo Flash. Charging the battery Your GEM+ light comes charged. However, before using it for the first time fully charge the device for maximum results. Connect the device to power using the supplied USB cable. The cable has two ends: USB type A and USB type C. Connect the USB type A plug to a standard outlet charger (maximum 1A). Connect the USB type C plug to the light. Switch on the power to charge. When the light is charging, the orange indicator light will illuminate in flashing orange, indicating the device is charging. When the device is fully charged, the indicator light will turn green. Ensure the rubber seal for the charging port is refitted and seated correctly after each charge. Battery level indication Upon powering your GEM+ light, when the lights are powered between 100% and 20% an LED light will show constant green. When the charge level is between 20 and 10%, one LED will show constant orange. When the light is powered below 10% , one LED will be flashing orange. Multifunction This bike light can be used as a working light or emergency flashlight, adaptable enough to be utilized while biking, hiking, working or other outdoor or indoor activities in darkness. The backside of the light is magnetic and can be attached so most steel surfaces through the magnetic function. Use & Care Only use a clean, damp cloth to clean the light unit. If cleaning your bicycle with a high-pressure cleaner, remove the light unit from your bicycle. If the GEM+ light will not be used for long periods, fully charge the battery, and store it in a cool and dry place. Be sure to fully charge the battery every 3 months. Trouble shooting If your GEM+ light malfunctions or fails to operate, follow the steps in this section to identify and resolve possible problems. If the light does not power on: Connect the light to power using the supplied USB cable and a supported wall charger. Check if the LED indicator light flashes orange. If so, the light might have run out of power and will need to be charged before use. The battery is connected to the battery charger, but the charger's LED indicator does not light up: Check that you are using a supported USB wall charger, which outputs a maximum of 5V and 1.0A. If you are experiencing any further problems with your GEM+ lights, please e-mail Reelight at info@reelight.com or call us at (+45) 86 74 24 90.Adobe PDF library 17.00 Adobe Illustrator 27.6 (Macintosh)