Home - Lunasea Lighting
Owner's Manual for Lunasea models including: LL64 LunaSafe Pool Boat Wearable Transmitter, LL64, LunaSafe Pool Boat Wearable Transmitter, Pool Boat Wearable Transmitter, Boat Wearable Transmitter, Wearable Transmitter, Transmitter
LunaSafe Pool/Boat Wearable Transmitter - Lunasea Lighting
File Info : application/pdf, 1 Pages, 169.45KB
DocumentDocumentLunaSafeTM Safety Products LL64 INSTRUCTIONS Transmitter Receiver/Alarm Transmitter Functions Transmitter is a wearable device that has a approx 5 year battery built in. When tranmitter comes in contact with water it will send a signal to the receiver alarm which will sound audible and visual alarm. Locking Wrist Strap After threading the nylon strap through safety device and back through the locking connector, turn locking button 90 degrees as shown using a coin or screwdriver. Unlocked Position Locked Position On/Off Button Ready Indicator Receive Indicator Pairing Indicator Low Battery Indicator Test Indicator Charge Indicator Internal Antenna Pair/Reset Button Emergency Strobe Light Audioable Alarm 1-800-272-0170 www.lunasea.com Wireless Charge Area Charging Receiver Make sure the unit is fully charged by placing it standing up on a charge pad. Then wait until Charging Light goes off. Turn Receiver On Momentarily press On/Off Button to turn on. Unit initializes and then Ready indicator blinks showing unit is in normal operation. Low Battery When battery becomes low the Low Bat Indicator will Blink. Place unit on Charge Pad until battery is fully charged. Charging light will then go off indicating full charge. Pairing Receiver with Transmitter Press and hold the Check Button for 5 seconds then with wet fingers, wet cloth or dipped in water across both gold pins. You will see Pairing indicator blink multiple times showing the the device has been paired. You can do this with up to 25 tranmitters. To delete all pairing information, press and hold the Check Button for 10 seconds. This will erase all pairing memory. You may now pair new units to the receiver. Check Button Gold Pins Alarm in Progress When Transmitter comes in contact with water the Strobe Light on the Receiver activates and a Lound Alarm activates. As soon as gold pins are dry the device stops transmitting, however the Receiver Alarm will continue to sound alarm. To reset the Receiver, press the Pair/Reset Button or the On/Off Button. If On/Off Button is pressed the unit will be in off state and will no longer monitor. FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. IC WARNING This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: 1. L'appareil ne doit pas produire de brouillage; 2. L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.