User Manual for SC T models including: HS04, HDMI Repeater, HS04 HDMI Repeater
prieš 15 valandų — User Manual. HS04. Introduction. HS04 is a 4 input HDMI automatic switcher that supports resolution up to 1080p. The auto-scan function.
User Manual. HS04. Introduction. HS04 is a 4 input HDMI automatic switcher that supports resolution up to 1080p. The auto-scan function.
HDMI Repeater User Manual Model : HS04 4 x 1 HDMI Switcher Smart Cabling & Transmission Corp. User Manual HS04 Introduction HS04 is a 4 input HDMI automatic switcher that supports resolution up to 1080p. The auto-scan function allows the switcher to switch to an available or last connected HDMI source automatically. It is a perfect solution for home theaters, security rooms, and so on -- no hassles plug-ins for different HDMI devices anymore. Features Resolution up to 1080p@60Hz. Supports auto-scan function, automatically switch to the next available input when the selected one is unable to display. Supports auto switching function, automatically switch to the last connected input source. Managed via IR remote or front panel buttons. Panel View IR Remote Control Setting This device could use IR remote control for function setting and control, The ID number must be setup before using IR remote control or change new batteries. Setup IR remote ID number: Press and hold "Power Symbol" button and press number 0. 1 Installation View User Manual HS04 Power AUTO SCAN AUTO JUMP 1, 2, 3, 4 ON/OFF FLASH ON/OFF ON/OFF ON FLASH System activate/ standby. Panel button or IR remote control disabled by remote PC. Auto scan function activated/disabled. Auto jump function activated/disabled. Currently selected input signal channel. No signal input. Panel Button Function Power: System activate/ standby. AUTO SCAN: Auto scan function activated/disabled. AUTO JUMP: Auto jump function activated/disabled. DIMMER: LED brightness adjustment. 1, 2, 3, 4: Currently select input signal channel and disable auto scan function. Remote Control Operating A,B Mode Switching There are two remote control operating modes: When this device power on, you could switch A,B mode by pressing the panel "power" button and remote control " *" button together. Mode A operating mode: It come with auto scan & auto jump functions. Mode B operating mode: When auto scan & auto jump functions no need to use, which only need single button for quick operation on AV switch. 2 Factory default is set to (Mode A). User Manual HS04 IR remote control Mode A Operating Power symbol 1234 (567) 0 # MENUENTER(567)89 System activate/standby. Select previous available input and activates auto scan function. Select next available input and activates auto scan function. Select previous input and disable auto scan function. Select next input and disable auto scan function. Currently select input and disable auto scan function. Auto jump function activated/disabled. LED brightness adjustment. Reserved (no function) . IR remote control Mode B Operating Power symbol 1234 (567) # MENUENTER(567)890 System activate/standby. Select previous input and system activate. Select next input and system activate. Select previous input and system activate. Select next input and system activate. Currently select input and system activate. LED brightness adjustment. Reserved (no function). Auto Scan Function Under auto scan operation, if the selected input video signal disappears over 0.5 second, it would automatically select the previous or next input with video signal. Auto Jump Function Under auto jump operation, if there is a new video signal input, it will automatically switch to a new video signal input. LED brightness setting LED brightness could be set up as the following 4 levels: 1 Minimum Brightness 2 Normal Brightness 3 Maximum Brightness 4 Brightness auto change 3 User Manual HS04 Factory default is set to level 3. Under Brightness auto change mode, press any button or IR remote control, or video signal changed (video signal disappears or show up), LED status will show the maximum brightness up to 5 seconds then back to the minimum brightness. Computer Remote Control Function This console could use optional USBRS-232 and RS-485 terminal cable to connect with computer, To use terminal program for remote control operation, the communication format is 9600,8,N,1 (9600 Bps, 1 start bits, 8 data bits, 1 stop bit). Under remote control operation, If it shows COMMAND, then it is "under command mode". It could easily be operated and set by entering the following commands in the chart. PressEnter: if it shows OK! then the previous command is completed; showing ERROR! indicates the previous command is incorrect. Command Mode Instruction [COMMAND] [DESCRIPTION] ------------------------- ------------------------------------------- n Currently select input and disable auto scan. PRE Select previous available input and activates auto scan. NEXT Select next available input and activates auto scan. SCAN y Auto scan function activated/disabled. JUMP y Auto jump function activated/disabled. ACTIVATE System activate. STANDBY System standby. MODE x Select operation mode A/B. IR y IR remote button lock/unlock. KEY y Panel button lock/unlock. LED n LED brightness adjustment. SAVE Save setting. LOAD Load setting. KEYPAD Keypad mode operation. SIGNAL Display input signal status. STATUS Display setting. VERSION Display firmware version. ? Show all commands. 4 [SYMBOL] [PARAMETER] ------------------------- ------------------------------------------- n 1 | 2 | 3 | 4 x A | B y ON | OFF Space characters between the command and parameters can be ignored. User Manual HS04 Virtual Remote Control Mode Showing KEYPAD : when it is under virtual remote control mode, which you could enter the following commands at the terminal to simulate the IR remote control operation. PressEnter: if it shows OK! then the previous command is completed; showing ERROR! indicates the previous command is incorrect. System Activate Virtual Remote Control Mode A/B Operate description MODE A [COMMAND] [DESCRIPTION] ------------------------- ------------------------------------------- 1 2 3 4 Currently select input and disable auto scan. - Select previous available input and activates auto scan. + Select next available input and activates auto scan. L Select previous input and disable auto scan. R Select next input and disable auto scan. 0 Auto jump function activated/disabled. / System activate/standby. . LED brightness adjustment. Q Command mode operation. S Display setting and input signal status. ? Show all commands. MODE B [COMMAND] [DESCRIPTION] ------------------------- ------------------------------------------- 1 2 3 4 Currently select input. - Select previous input. + Select next input. L Select previous input. R Select next input. / System activate/standby. . LED brightness adjustment. Q Command mode operation. S Display setting and input signal status. ? Show all commands. 5 User Manual HS04 System Standby Virtual Remote Control Mode A/B Operate description MODE A [COMMAND] [DESCRIPTION] ------------------------- ------------------------------------------- / System activate/standby. Q Command mode operation. S Display setting and input signal status. ? Show all commands. MODE B [COMMAND] [DESCRIPTION] ------------------------- ------------------------------------------- 1 2 3 4 Currently select input and system activate. - Select previous input and system activate. + Select next input and system activate. L Select previous input and system activate. R Select next input and system activate. / System activate/standby. Q Command mode operation. S Display setting and input signal status. ? Show all commands. Remark There are some DVD equipment still have +5V signal output under power off status, it will cause auto jump and auto scan function abnormal, please disable auto jump and auto scan function to avoid any abnormal operation. 6 Specification ITEM NO. Support Compliance Max. HDMI Resolution Video Bandwidth RS232 Baud Rate IR Support Ports & Interfaces Video Input Video Output RS232 Interface (Console) Power Power Supply Power Consumption Ambient Temperature Operation Storage Humidity Physical Characteristics Dimensions Weight Item NO. Ambient Temperature Storage Humidity Physical Characteristics Dimensions HS04 HDM 1.3a, HDCP 1080p@60Hz 12bits 2.25 Gbps 9600 bps 38Khz , ±45°, 5M 4 x HDMI Type A 1 x HDMI Type A 1 x DB9 Female DC 5V 1A 300mA 0 to 55 -20 to 85 Up to 95% 253 x 138.5 x 40mm 770g RC01 -20 to 85 Up to 95% 57.5 × 33.5 × 16.8mm 7 User Manual HS04iLovePDF