JENSON MPR2110 Digital Media Receiver Owner's Manual

Owner's Manual for JENSON models including: MPR2110, 110MPR2110, MPR2110 Digital Media Receiver, MPR2110, Digital Media Receiver, Media Receiver, Receiver

110MPR2110

110MPR2110, Jensen MPR2110 Digital Media Receiver, WWW.CRUTCHFIELD.COM

110MPR2110;, Jensen, MPR2110, Digital, Media, Receiver;, WWW.CRUTCHFIELD.COM

HNEWBERRY

Jensen MPR2110 owner's manual

Jensen MPR2110 Digital media receiver (does not play discs) at Crutchfield

Jensen MPR2110 Digital media receiver at Crutchfield

File Info : application/pdf, 24 Pages, 2.23MB

110MPR2110

MPR2110
INSTALLATION/OWNER'S MANUAL
AM/FM Receiver with Bluetooth and Fixed Face

MPR2110 INSTALLATION

Preparation

Please read entire manual before installation.

Before You Start · Disconnect negative battery terminal. Consult a qualified technician for instructions. · Avoid installing the unit where it would be subject to high temperatures, such as from
direct sunlight, or where it would be subject to dust, dirt or excessive vibration.

Mounting the Head Unit: Typical DIN mounting
Step 1: Insert the mounting sleeve into the installation kit or dashboard.

Single DIN
Dashboard or Installation Kit
Mounting Sleeve

Step 2: Bend multiple mounting tabs around the mounting sleeve until the mounting sleeve is secure.

Single DIN
Dashboard or Installation Kit Mounting Sleeve
Mounting Tabs

Step 3: Connect all wiring harnesses and slide the head unit into the mounting sleeve until it clicks into place.
Mounting the Head Unit: ISO mounting
Using the existing brackets or the brackets supplied with the installation kit, mount the brackets to the sides of the head unit with the screws supplied with the head unit.
2

Single DIN
Dashboard or Installation Kit

Head Unit

Mounting Sleeve

Single DIN

Decorative Bezel

New Radio

Existing Brackets

MPR2110 INSTALLATION
Wiring Diagram
FUSE
When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could
damage the radio. The unit uses
one 10 amp ATM fuse located beside the Heat Sink
3

MPR2110 OPERATION
Control Locations

4 5

14 13 12 11 10 9 8

1 Power 2 Band 3 Mute 4 Volume Knob 5 Automatically Store 6 USB Port

7 Auxiliary Input 8 Preset 6 / Folder Up 9 Preset 5 / Folder Down 10 Preset 4 / Random 11 Preset 3 / Repeat 12 Preset 2 / Intro

13 Preset 1 / Play/Pause 14 Display 15 Mode 16 Reset 17 Tune Up 18 Tune Down

17 16 15 14 13 12

1 Mode

10 Preset 6 / Folder Up

2 Volume Up

11 Mute

3 Power

12 AS/PS

4 Audio

13 Preset 5 / Folder Down

5 Tune Up

14 Preset 4 / Random

6 Volume Down

15 Preset 1 / Play / Pause

7 Band

16 Bluetooth Talk

8 Preset 3 / Repeat 17 Tune Down

9 Preset 2 / Intro

MPR2110 OPERATION
General Operation
Power On/Off Press the button to turn the unit on. Press again to turn the unit off.
Changing Modes Press MODE to select between Radio, USB, Auxiliary Input and Bluetooth. Modes of operation are shown in the display.
Volume Adjust volume using the volume knob (00-43). Mute Press to silence the audio. Press again to resume listening at the previously selected volume.
Auxiliary Inputs Insert a 3.5mm cable in the unit's front AUX port. Reset Press the RESET button to reset the unit back to the factory settings if abnormal operation occurs. The reset button is located on the front panel.
Setting the Clock With the unit on, press DISP to display clock time. Press and hold DISP until the hours begins to flash, then release.
nn ll Press the TUNE and TUNE to adjust the hours,
then press the DISP, the minutes begins to flash, press the
nn ll TUNE and TUNE button to adjust the minutes.
Press DISP momentarily to save the selected time. Display Press DISP to toggle display between various displayed
information. Audio / Menu Press the volume knob momentarily to select between audio
functions. Press and hold the volume knob for more than two seconds to select between the menu functions. Rotate the volume knob left/right to adjust or activate the desired function/audio.
5

MPR2110 OPERATION

AM/FM Tuner Operation

nn ll Seek Tuning Press TUNE or TUNE to seek to the previous or next strong station.

Manual Tuning

nn ll Press and hold TUNE or TUNE to enter manual nn ll tuning mode, then press TUNE or TUNE
momentarily to change radio frequency up or down one

nn ll step at a time. Press and hold TUNE or TUNE

advance quickly.

Band

Press BAND to select between FM1, FM2, FM3, AM1 and AM2 bands. Up to six presets can be programmed for each band, enabling up to 18 FM stations and 12 AM stations to be stored in memory.

Storing Presets

Up to 18 FM and 12 AM stations can be stored. To store a station, select the desired band and station. Press and hold the desired preset button (1-6) for more than two seconds. When stored, the preset number will appear in the display.

Recalling Presets Preset stations can be recalled any time by pressing the corresponding preset button.

Automatically Store Press and hold AS/PS for more than 2 seconds to store 18 FM stations and 12 AM stations automatically.
Preset Scan Stations Press AS/PS to recall each preset staion that stored in the memories in each band.

MPR2110 OPERATION

USB Operation

Playing MP3 Files To play MP3 files, insert a USB device containing MP3 files.

ll Track Select Press TUNE

to skip to the beginning of the next track.

nn Press TUNE

to skip to the beginning of the previous

track.

ll nn Fast Forward Press and hold TUNE or TUNE

to fast forward or

and Reverse reverse a track.

Pause Folder Access

Press / II to temporarily stop USB playback.
ll Press / II again to resume playback.
Folders can be found by pressing Folder Up or Folder Down. About one second after the folder name is displayed, the first file under the selected folder will be displayed and playback will begin.

Repeat

Press RPT to toggle between RPT ALL, RPT FLR and RPT ONE. · RPT ALL - Plays all tracks on USB device. · RPT ONE - Continuously repeats selected track. · RPT FLR - Continuously repeats all files in current folder.

Random Press RDM to play tracks in random order; press again to cancel the RDM function.

Intro Press INT to play the first 10 seconds of each track; press again to cancel the INT function.

MPR2110 OPERATION

Bluetooth Operation

Preparation Before using a Bluetooth device, it must be paired and connected. Ensure that Bluetooth is activated on your device before beginning the pairing process.

Pairing a New Device

The head unit broadcasts the pairing signal constantly when no devices are connected. Complete the pairing sequence from your Bluetooth device. Refer to the owner's manual for your device for more details.

The device name is "Jensen Media Player". The Bluetooth passcode is "1234".

Note: The head unit can be in any mode of operation when pairing is performed.

Streaming Audio The head unit supports A2DP wireless streaming audio Troubleshooting from a Bluetooth mobile device directly to your head unit.
The following functions can be used to control the music:

ll · Press

to skip to the next available audio track.

nn · Press

to skip to the previous audio track.

l · Press / II to toggle between play and pause during playback.

MPR2110 OPERATION
Troubleshooting

Problem
Unit will not turn on (no power)
Unit has power (but no sound)
Unit blows fuses
NO FILE appears on display
NO SUPPORT appears on display

Cause

Action

Yellow wire not connected or incorrect voltage Red wire not connected or incorrect voltage Black wire not connected Fuse blown Speaker wires not connected
One or more speaker wires touching each other or touching chassis ground
Yellow or red wire touching chassis ground
Speaker wires touching chassis ground Incorrect fuse rating

Check connections for proper voltage (11~16VDC)
Check connection to ground Replace fuse
Check connections at speakers Insulate all bare speaker wires
from each other and chassis ground
Check for pinched wire
Check for pinched wire Use fuse with correct rating

No playable MP3 files found on the device

Check the device for valid MP3 files

An invalid ID3 tag version is present

Version 1.0 to 2.0 ID3 tags are supported.

MPR2110 OPERATION

Limited One Year Warranty

This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
Namsung America Inc. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase.
Namsung America Inc. agrees, at our option, during the warranty period, to repair any defect in material or workmanship or to furnish an equal new, renewed or comparable product (whichever is deemed necessary) in exchange without charges, subject to verification of the defect or malfunction and proof of the date of purchase. Subsequent replacement products are warranted for the balance of the original warranty period.
Who is covered? This warranty is extended to the original retail purchaser for products purchased from an authorized Jensen dealer and used in the U.S.A.
What is covered? This warranty covers all defects in material and workmanship in this product. The following are not covered: software, installation/removal costs, damage resulting from accident, misuse, abuse, neglect, product modification, improper installation, incorrect line voltage, unauthorized repair or failure to follow instructions supplied with the product, or damage occurring during return shipment of the product. Specific license conditions and copyright notices for the software can be found via www. jensenmobile.com.

What to do? 1. Before you call for service, check the
troubleshooting guide in your owner's manual. A slight adjustment of any custom controls may save you a service call.
2. If you require service during the warranty period, you must carefully pack the product (preferably in the original package) and ship it by prepaid transportation with a copy of the original receipt from the retailer to an authorized service center.
3. Please describe your problem in writing and include your name, a return UPS shipping address (P.O. Box not acceptable), and a daytime phone number with your shipment.
4. For more information and for the location of the nearest authorized service center please contact us by one of the following methods:
· Call: 888-921-4088 · E-mail: jensenmobile2015@gmail.com
Exclusion of Certain Damages: This warranty is exclusive and in lieu of any and all other warranties, expressed or implied, including without limitation the implied warranties of merchantability and fitness for a particular purpose and any obligation, liability, right, claim or remedy in contract or tort, whether or not arising from the company's negligence, actual or imputed. No person or representative is authorized to assume for the company any other liability in connection with the sale of this product. In no event shall the company be liable for indirect, incidental or consequential damages.

MPR2110 OPERATION
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected. · Consult the dealer or an experienced radio/TV technician for help.
11

MPR2110 OPERATION
Specifications

FM Tuner

Tuning range: 87.5MHz-107.9MHz Usable sensitivity: 8.5dBf 50dB quieting sensitivity: 10dBf Stereo separation @ 1kHz: >30dB Frequency response: 30Hz-13kHz

AM Tuner

Tuning range: 530kHz-1710kHz Usable sensitivity: <42dBu Frequency response: 30Hz-2.2kHz

General

Speaker output impedance: 4~8 ohms Line output voltage: 2 Volts RMS Dimensions: 7" x 3.8" x 2" (178 x 97 x 50 mm)

Design and specifications subject to change without notice.

CEA-2006 Power Standard Specifications (reference: 14.4VDC +/- 0.2V, 20Hz~20kHz)
Power Output: 16 Watts RMS x 4 channels at 4 ohms and < 1% THD+N Signal to Noise Ratio: 75dBA (reference: 1 watt into 4 ohms)
12

Notes

MPR2110 OPERATION

Dual Electronics Corp. Toll Free: 888-921-4088
www.jensenmobile.com ©2019Namsung America Inc. All rights reserved. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc.
Other trademarks and trade names are those of their respective owners.
NSA0719-V01

MPR210
QUICK START GUIDE
Digital Media Receiver
· · · · · · · · · · · · · ·
JENSEN
To download a complete owner's manual visit www.jensenmobile.com or call customer service 1-888-921-4088
(Monday-Friday,9AM-5PM EST)

Installation
Before You Start · Consult a qualified technician for instructions. Jensen always recommends
professional installation. · Disconnect negative battery terminal. · Insert the removal keys. and remove the mounting sleeve from the head unit.
Installation Process 1. Carefully remove the existing head unit. (if applicable)
2. Connect wiring harness. Consult a qualified technician if you are unsure. 3. Mount the head unit using the mounting sleeve. 4. Connect wiring harness and antenna. Test the head unit for correct operation.
5. Slide the radio into the mounting sleeve to secure the radio.
6. Snap silicon caps into place.
Wiring Connections
The chart below the connection for each wire in the wiring harness.

Color
Red Yellow Black
Blue White White/Black
Gray Gray/Black
Green Green/Black
Violet Violet/Black

Connection
Ignition / ACC 12V(+) 12V Battery I Memory
Ground Power Antenna/ Amp Turn-on
Left Front (+) Left Front (-) Right Front (+) Right Front(-) Left Rear(+) Left Rear(-) Right Rear(+) Right Rear(-)

Tip:
When a suitable ground wire is not present in the vehicle wiring harness. connect the black ground
wire to the vehicle chassis.
Fuse:
When replacing the fuse. make sure new fuse is the correct type and amperage. Using an incorrect
fuse could damage the radio.

Mounting the Head Unit: Typical DIN mounting
Step 1: Insert the mounting sleeve into the
installation kit or dashboard.

Dashboard or Installation Kit

Dashboard or Installation Kit
Step 2: Bend multiple mounting tabs around the mounting sleeve until the mounting
sleeve is secure.

Mounting Sleeve

Step 3: Connect all wiring harnesses and slide the head unit into the
mounting sleeve until it clicks into place.

Dashboard or Installation Kit Mounting Sleeve

Step 4: Remove the plastic caps and use the removal keys
to remove the unit.

Removal Keys

General Operation

Power On/Off Press the (.!) button to turn the unit on. Press (.!) again to
turn unit off.

Changing Modes

Press MODE to select between Radio, USB, Bluetooth, AUX.
Modes of operation are shown in the display.

Volume Adjust volume using volume knob.

Mute Press~ to silence the audio. Press~ again to resume
listening at the previously selected volume.

Auxiliary Inputs Insert a 3.5mm cable in the units front AUX port.

Reset

Press the RESET button to reset the unit back to the factory settings if abnormal operation occurs. The reset button is located on the front panel.

Setting the Clock

With the unit on, long press DISP to display clock time. Press and hold DISP until the hours or minutes begin to flash, then release. Rotate the volume knob to adjust the time. Long press DISP to finish the clock setting.

Display Press DISP to toggle display between various displayed
information.

Audio/ Menu

Press volume knob momentarily to select between the audio functions. Press and hold volume knob for more than two seconds to select between the menu functions. Rotate the volume knob left/right to adjust or activate the desired function/audio.

· · · · · · · · · · · · · · · ·
To download the complete Owner's Manual for your radio, please visit www.dualav.com/support/manuals.php.

AM/FM Tuner Operation

Seek Tuning Manual Tuning
Band

Press TUNE

or TUNE

strong station.

to seek to previous or next

Press and hold the TUNE

or TUNE

to enter manual

tuning mode. Then press TUNE

or TUNE momentarily

to move radio frequency down or up one step at a time.

Press and hold TUNE

or TUNE

to advance quickly.

Press BAND to select between FM1, FM2, FM3, AM1
and AM2 bands. Up to six presets can be programmed for each band. enabling up to 18 FM stations and 12 AM stations to be stored in memory.

Storing Presets

Recalling Presets Preset stations can be recalled any time by pressing the
corresponding preset button.

Auto store Press and hold MENU for more than 2seconds ,then press DISP to store 18 FM stations and 12 AM stations automatically.

Preset Scan Touch PS to recall each preset station that has been stored in memory for each band.
(Available with the Jensen Smart Remote App only)

· · · · · · · · · · · · · · · ·
To download the complete Owner's Manual for your radio. please visit www.dualav.com/support/manuals.php.

USB Operation

Playing MP3 Files To play MP3 files. insert a USB device containing MP3 files.

Track Select Press TUNE Press TUNE
song.

to skip to the beginning of the next song. to skip to the beginning of the previous

Fast Forward and Press and hold TUNE or TUNE Reverse or reverse a track.

to fast forward

Pause Press / II to temporarily stop playback. Press / II again to resume playback.

Folder Access

Folder can be found by pressing Folder Up or Folder Down. About 1 second after the folder name is displayed. the first file under the selected folder will be displayed and playback.

Repeat Random

Press RPT to toggle between RPT ALL and RPT ONE.
· RPT ALL - Plays all tracks on USB device. · RPT ONE - Continuously repeats selected track.
Press RDM to play tracks in random order. press again to cancel the RDM function.

Intro Press INT to plays first 10 seconds of each track. press
again to cancel the INT function.

· · · · · · · · · · · · · · · ·
To download the complete Owner's Manual for your radio. please visit www.dualav.com/support/manuals.php.

Bluetooth® Operation

Preparation
Pairing a New Device

Before using a Bluetooth device, it must be paired and connected. Ensure that Bluetooth is activated on your device before beginning the pairing process.
The head unit broadcasts the pairing signal constantly when no devices are connected. Complete the pairing sequence from your Bluetooth device. Refer to the owner's manual for your device for more details.
The device name is "Jensen Media Player"
Note: The head unit can be in any mode of operation when pairing is performed.

Streaming Audio Troubleshooting

The head unit supports A2DP wireless streaming audio

from a Bluetooth mobile device directly to your head unit.

The following functions can be used to control the music:

s Press

to skip to the next available audio track.

ll s Press

to skip to the previous audio track.

nn s Press / II to toggle between play and pause during

l playback.

· · · · · · · · · · · · · · · ·
To download the complete Owner's Manual for your radio, please visit www.dualav.com/support/manuals.php.

APP Operation
The Jensen Smart App is the ultimate wireless remote control for your receiver. You can download Jensen Smart app from Apple App Store or Google Play Store and install it on your smartphone or tablet. Please scan the following QR code to download the Jensen J-Link P2 APP to your smart phone.
CD
LINK
Voice Activation Operation
Bluetooth should be paired between your smartphone and the receiver. Press the voice activation button , and the receiver will switch into Bluetooth mode, This will activate Siri® or Google AssistantTM on your smartphone. You will need to manually switch back to the previous or desired mode once this operation is terminated.

Limited One-Year Warranty
This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Namsung America Inc. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase. Namsung America Inc. agrees. at our option. during the warranty period. to repair any defect in material or workmanship or to furnish an equal new. renewed or comparable product (whichever is deemed necessary) in exchange without charges. subject to verification of the defect or malfunction and proof of the date of purchase. Subsequent replacement products are warranted for the balance of the original warranty period.
Who is covered? This warranty is extended to the original retail purchaser for
products purchased and used in the U.S.A.
What is covered? This warranty covers all defects in material and workmanship
in this product. The following are not covered: installation/removal costs. damage resulting from accident. misuse. abuse. neglect. product modification. improper installation. incorrect line voltage. unauthorized repair or failure to follow instructions supplied with the product. or damage occurring during return shipment of the product.
What to do?
1. Before you call for service. check the troubleshooting guide in your owner's manual. A slight adjustment of any custom controls may save you a service call.
2. If you require service during the warranty period. you must carefully pack the product (preferably in the original package) and ship it by prepaid transportation with a copy of the original receipt from the retailer to an authorized service center.
3. Please describe your problem in writing and include your name. a return UPS shipping address (P.O. Box not acceptable). and a daytime phone number with your shipment.
4. For more information and for the location of the nearest authorized service center
please contact us toll-free at 1-888-921-4088 or by email at cs@dualav.com.
Exclusion of Certain Damages: This warranty is exclusive and in lieu of any
and all other warranties. expressed or implied. including without limitation the implied warranties of merchantability and fitness for a particular purpose and any obligation. liability, right. claim or remedy in contract or tort. whether or not arising from the company's negligence. actual or imputed. No person or representative is authorized to assume for the company any other liability in connection with the sale of this product. In no event shall the company be liable for indirect. incidental or consequential damages.

FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference. and (2) this device must accept any interference received. including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class 8
digital device. pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates. uses and can radiate radio frequency energy and. if not installed and used in accordance with the instructions. may cause harmful interference to radio communications. However. there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception. which can be determined by turning the equipment off and on. the user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected. · Consult the dealer or an experienced radio technician for help.
Customer Service Toll Free: 1-888-921-4088
www.jensenmobile.com ©2019 Namsung America Inc. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. Siri and Apple are registered trademarks owned by Apple Inc. Google Assistant and Android are trademarks owned by Google LLC. Other trademarks and trade names are those of their respective owners.
NSC1019-V01

References

Adobe Acrobat Pro DC (32-bit) 21 Paper Capture Plug-in