Instructions for HEVAC models including: AWECv Series, AWECv Series EC Fan Auto Modules, EC Fan Auto Modules, Auto Modules, Modules
AWEC-3V 3 Channel AUTO/MANUAL EC FAN SPEED CONTROLLER c/w 12v power - Hevac Control Agencies
File Info : application/pdf, 2 Pages, 690.70KB
DocumentDocumentAWECv SERIES EC FAN AUTO/MANUAL MODULES COMPLETE WITH ONBOARD 10vDC MANUAL POTENTIOMETER SUPPLY & SELECTION OF N/O or N/C FAN ENABLE. AWEC-1v AWEC-3v · Made in Australia to Australian Standards. · Multiple I/O versions : single, 3 way, 5way. · Auto / Manual inputs can be looped to other 24vAC relays etc. · Manual potentiometer can adjust output from 0-10vDC. · Potential Free (24v 1Amp max.) SPST Fan Enable Relay Output ...selectable by jumper as N/O or N/C potential free contacts. · Optional use Onboard 10vdc power supply for manual potentiometer signal source to save 3rd wire (10v source) from EC fan. · 2 or 3 wire signal to EC fan (+ 2 wires if relay enable O/P required) · Din rail mount low profile. APPLICATION The AWECv modules are intended for use as a low cost alternative to traditional plug in relays & potentiometers for Auto/Off/Manual EC fan speed interlocks & control. The device is available in 3 versions - a Single output module AWEC-1v, AWEC-3v or a 5 way version AWEC-5v. The output signal to the EC fan is derived either from the onboard potentiometer/s (in manual mode) or to pass out the 0-10vdc signal/s from an external control device ie BMS EC fan speed control outputs. The AWECv version comes with an optional use 10vDC power supply that can be used to power the onboard manual speed potentiometer saving the need to bring a 3rd wire (the 10v source) from the EC fan which reduces the typical connection from 3 wires to 2. The potentiometer shaft/knob can be removed exposing only a hexagonal hole to decrease the ability of tampering post commissioning manual fan speed settings if desired. HEVAC CONTROL AGENCIES PTY.LTD www.hevac.com.au 613 95627888 TERMINAL LEGEND MAN.POT. VOLTAGE SELECTOR FAN ENABLE JUMPER N/C N/O FIT JUMPER TO USE ONBOARD 10V SUPPLY NOTE TERMINAL "GO" & "0" INTERNALLY LINKED FOR A COMMON GROUND REFERENCE. TRACK CAN BE CUT IF REQUIRED TO ISOLATE. IF EXTERNAL 10vDC SUPPLY USED REMOVE ONBOARD 10V SUPPLY JUMPER (right hand side of pcb). FAN ENABLE CONTACTS CAN BE SET AS N/O (default) or N/C GO 24v NEUTRAL D1 24v ACTIVE to energise relay 1 (Manual) D2 24v ACTIVE to energise relay 2 (Auto) Q1 & Q2 Auxiliary SPST N/O or N/C contacts X External (AUTO) 0-10vdc signal input 0 EC Fan & potentiometer DC ground interlock Y EC Fan 0-10Vdc output control interlock 10 10vDC Supply from EC Fan (If onboard supply not used) DIMENSIONS N/O-N/C SELECT JUMPER BMS RUN INTERLOCK CONTACTS CAN BE SET AS N/O or N/C BMS RUN INTERLOCK onboard 10vdc supply jumper removed. BASIC EC FAN SPEED CONTROL WITH VARIABLE EXTERNAL CONTROL INPUT & MANUAL SPEED SELECTION VIA 3 POSITION SWITCHBOARD SWITCH. EC FAN SPEED CONTROL WITH VARIABLE EXTERNAL INPUT & MANUAL SPEED VIA SWBD SWITCH C/W FAN RUN RELAY ENABLE OUTPUT. BASIC MANUAL EC FAN SPEED HEVAC CONTROL AGENCIES PTY.LTD www.hevac.com.au 613 95627888