User Guide for TORO models including: SPRAYS
Toro 89-3747 570 Black Molded Cap | PlumbersStock
Toro 570Z-6LP 6" Pop-Up Sprinkler for Low Pressure | PlumbersStock
Toro 89-3979 570Z 6" Pop-Up Sprinkler | PlumbersStock
RUGGED FLEXIBLE VERSITILE RELIABLE: Toro® 570Z Series spray heads provide a durable solution for residential and commercial contractors to satisfy all installation and retrofit requirements. In combination with Toro spray and rotating nozzles, 570Z Series spray heads can be configured in hundreds of combinations and present an unparalleled range of flexibility. Available in 2", 3", 4", 6" and 12" models with both bottom and side inlet thread options, Toro 570Z Series spray heads are further available with patented in-stem X-Flow® Technology and Pressure Regulating water-saving features. Trusted for over 25 years, Toro's 570Z Series spray heads are the ideal choice. 14 SPRAYS 570Z SERIES SPRAY BODIES FEATURES & BENEFITS Zero Flush Wiper Seal The elimination of flushing on pop-up allows for more sprinklers to be installed per zone. Patented X-Flow® Technology The X-Flow in-stem flow shut-off device is built into the riser and restricts water loss by 99% should the nozzle be removed or damaged. The exclusive X-Flow device greatly reduces water waste, landscape erosion, and wet hardscape safety concerns. Furthermore, X-Flow allows for `dry' nozzle and filter replacement or system maintenance while the system is running. One-Piece Check Valve (570CV) Pre-installed from the factory or easily installed in the field, Toro's one-piece check valve prevents low-head drainage on elevation changes of up to 10 feet. Ratcheting Riser Quick and precise arc adjustment on all pop-up models. Options Available Serviceable Check Valve (570CV) prevents low-head drainage on elevation changes of up to 10 feet (not compatible with Side Inlet or Shrub models) Replacement Zero-Flush seal (570SEAL) Effluent water indicators: Effluent Shrub Adapter (102-1231) Effluent snap-on cap cover (89-9752) Effluent Cap with seal (102-1211) 6" Riser Extender (570-6X) 6" Stationary Riser (570-SR-6) [1/2" male-threaded inlet] 18" Stationary Riser (570-SR-18) [1/2" male-threaded inlet] Riser Pull-up Tool (89-6395) Nozzle Adjustment Key (89-7350) Additional Features Corrosion-resistant stainless steel retraction spring All models shipped with installed flush plug Effluent Options Available Check Valve Options Available 15 PRODUCT HIGHLIGHT Enhanced Zero Flush Seal No Water Wasted at System Start System start up is a critical time when water waste can occur. The Toro 570Z Series spray head's wiper seal is pressure-activated and prevents flow-by at start up, meaning no water is wasted and more heads can be installed on the same line. Patented X-Flow® Shut-off Device X-Flow® Technology Cuts Off Water Waste Up to 40 gallons of water per minute can escape through a spray head that has a missing or damaged nozzle. This wasted water can lead to landscape erosion, property damage, or unsafe conditions due to wet hardscapes. The patented X-Flow device is factory-installed in the riser and holds back over 99% of the water that would otherwise be wasted in cases where the nozzle has been compromised through unintentional accidents or vandalism. Furthermore, X-Flow Technology allows for spray head maintenance or component replacement without the need to turn off the system. Without X-Flow With X-Flow Pressure Regulator Reliability thanks to Built-in Pressure Regulation Toro's factory-installed pressure regulator eliminates water misting and fogging at the nozzle that can lead to rapid evaporation or water being blown away from the intended irrigation area. From the first to the last head, the in-stem pressure regulator provides a steady outlet pressure of 30 PSI and consistent spray head performance across the zone. Without Pressure Regulation With Pressure Regulation 16 SPRAYS SPECIFICATIONS Operational · Radius: 2 feet to 26 feet · Operating pressure range: 20-75 psi (15-75 psi for Low Pressure models) · Recommended operating pressure for spray nozzles: 30 psi · Recommended operating pressure for rotating nozzles: 45 psi · Flow rate: 0.5 4.5 gpm Dimensions · Body diameters: 13/8" on 2", 3", 4", 6" and 6" Side Inlet 15/8" on 12" 13/4" on 12" Side Inlet · Cap diameter: 2" · Inlet thread: 1/2" Female · Side inlet location: 43/4" (measured from the top of spray head to center of the side inlet port) Warranty · Five years on all models 570Z & 570ZLP 570S Shrub Adapter 570Z-2P 2" Spray Head 570Z-2LP 2" Spray Head, Low Pressure 570Z-3P 3" Spray Head 570Z-3LP 3" Spray Head, Low Pressure 570Z-4P 4" Spray Head 570Z-4LP 4" Spray Head, Low Pressure 570Z-6P 6" Spray Head 570Z-6LP 6" Spray Head, Low Pressure 570Z-6SI 6" Spray Head, Side Inlet body 570Z-6LPSI 6" Spray Head, Low Pressure, Side Inlet body 570Z-12P 12" Spray Head 570Z-12LP 12" Spray Head, Low Pressure 570Z-12SI 12" Spray Head, Side Inlet body 570Z-12LPSI 12" Spray Head, Low Pressure, Side Inlet body 570Z-4P-COM 4" Spray Head with Check Valve 570Z-6P-COM 6" Spray Head with Check Valve 570Z-12P-COM 12" Spray Head with Check Valve 570ZXF 570S-XF Shrub Riser with X-Flow 570Z-4P-XF 4" XF Spray Head 570Z-6P-XF 6" XF Spray Head 570Z-6SI-XF 6" XF Spray Head, Side Inlet Body 570Z-12P-XF 12" XF Spray Head 570Z-12SI-XF 12" XF Spray Head, Side Inlet Body 570Z-4P-XFCOM 4" XF Spray Head with Check Valve 570Z-6P-XFCOM 6" XF Spray Head with Check Valve 570Z-12P-XFCOM 12" XF Spray Head with Check Valve 570ZPR 570S-PR PR Shrub Riser 570Z-4P-PR 4" PR Spray Head 570Z-6P-PR 6" PR Spray Head 570Z-12P-PR 12" PR Spray Head 570Z-4P-PRCOM 4" PR Spray Head with Check Valve 570Z-6P-PRCOM 6" PR Spray Head with Check Valve 570Z-12P-PRCOM 12" PR Spray Head with Check Valve 570ZPRX 570S-PRX PRX Shrub Riser 570Z-4P-PRX 4" PRX Spray Head 570Z-6P-PRX 6" PRX Spray Head 570Z-6SI-PRX 6" PRX Spray Head, Side Inlet Body 570Z-12P-PRX 12" PRX Spray Head 570Z-12SI-PRX 12" PRX Spray Head, Side Inlet Body 570Z-4P-PRXCOM 4" PRX Spray Head with Check Valve 570Z-6P-PRXCOM 6" PRX Spray Head with Check Valve 570Z-12P-PRXCOM 12" PRX Spray Head with Check Valve Base Model 570X S -- Shrub Z -- Lawn Pop-up Specifying Information--570Z Series 570X-XXXXX-XXXXXXX Pop-Up Height Spring and Inlet Optional Optional Optional XX XXX- XXX XXX X 2 -- 2" 3 -- 3" 4 -- 4" 6 -- 6" 12 -- 12" P -- Standard LP -- Low Pressure SI -- Std. Side Inlet* LPSI -- Low Pressure SI XF -- X-Flow® Technology PR -- Pressure Regulator PRX -- Pressure Regulator with XF COM -- Check Valve** E -- Effluent Example: A 570Z PRX Series Sprinkler with a 6" pop-up height, side inlet would be specified as: 570Z-6SI-PRX *Available for 6" and 12" models. **Not compatible with Side Inlet or Shrub models. 173-Heights(TM) PDF Security Shell 4.8.25.2 (http://www -tools.com)