ASSEMBLY INSTRUCTIONS BATH VANITY-CABINET
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small parts which may have come loose inside the carton during shipment. Separate, identify and count all parts and hardware. Compare with the parts list to be sure all parts are present.
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED
- Use of power tool to assemble this product will invalidate any claim and damage this product making unsafe!!! [power-tool-forbidden]
- Please assemble on a clean soft surface to avoid damage.
Estimated assembly time: [estimated-assembly-time] 2:00 h
Tools Required: [screwdriver-flathead], [screwdriver-phillips] (Not included)
IMPORTANT: PLEASE READ INSTRUCTION BEFORE STARTING THE ASSEMBLY
Important Notice
[STOP] PLEASE DO NOT RETURN TO STORE
Please do not return this product to the retailer!! We are able to assist you in ANY way.
If you find that you have any trouble with assembly or missing or damaged parts please contact the seller.
Before Installation
Thank you for purchasing this quality product. Be sure to check all packing materials carefully for small parts, which may have come loose inside the carton during shipment. Identify and count all items according to the PARTS LIST and/or HARDWARE LIST shown below. Check you have all the components and tools listed on the following pages.
- We recommend that you assemble this product with the assistance of another person; this will make the assembly easier, and will help eliminate damage to the product or injury to persons during assembly. [two-people-recommended]
- Please do not over tighten screws or bolts until the assembly is completed.
- Keep children and animal away from the work area, small parts could choke if swallowed.
- Please put all parts on a non-abrasive floor before assembly, and follow the assembly steps to assemble your newly purchased product correctly and efficiently.
Cam Lock Assembly Instructions
Diagram A: Insert Cam Ball into hole as shown in diagram A.
Diagram B: Make sure not to insert the Cam Bolt too deep as shown in figure B as this will cause the cam Lock to be misaligned and unable to interlock properly.
Diagram C: Also avoid inserting the Cam Bolt too close to the surface of the hole as shown in figure C, as this will cause the Cam Lock to be too loose, and not interlock properly.
Connect the panels together.
[arrow-sign] Insert the Cam Lock so the side opening fits over the head of the Cam Bolt.
To tighten the Cam Lock, turn it clockwise on half a turn with a flat screwdriver. [flat-screwdriver]
*Do not use an automatic screwdriver as it may bend or break if too much power is imposed.
Detail View
This section provides an exploded view of the vanity cabinet components, labeled with numbers for identification in the parts list.
Key components shown include the sink/lavabo (22), side panels (1, 2), frame bottom (3), various crossbars (4, 5, 6, 7, 8), drawer compartments (9, 10), drawer panels (11, 12, 13, 14, 15), drawer faces (16), support bars (17, 18, 19), and cabinet doors (20, 21).
Parts List
| Part No. | Description | Quantity |
|---|---|---|
| 1 | Side Panel (L) | 1pc |
| 2 | Side Panel (R) | 1pc |
| 3 | Frame Bottom | 1pc |
| 4 | Rear Crossbar Bottom 1 | 1pc |
| 5 | Rear Crossbar Bottom 2 | 1pc |
| 6 | Rear Crossbar Bottom 3 | 1pc |
| 7 | Front Crossbar Top | 1pc |
| 8 | Front Crossbar Bottom | 1pc |
| 9 | Vertical learning Compartment | 2pcs |
| 10 | Drevent Studing | 1pc |
| 11 | Bottom Drawer Panel Rear | 1pc |
| 12 | Bottom Drawer Panel Side (R) | 1pc |
| 13 | Bottom Drawer Panel Side (L) | 1pc |
| 14 | Panel Bottom | 1pc |
| 15 | Bottom Drawer Face | 1pc |
| 16 | Doc Bar (L) | 2pcs |
| 17 | Doc Bar (R) | 2pcs |
| 18 | Horizontal Bar 1 | 4pcs |
| 19 | Horizontal Bar 2 | 4pcs |
| 20 | Door Cabinet (L) | 1pc |
| 21 | Door Cabinet (R) | 1pc |
| 22 | Lavabo | 1pc |
Hardware List
| Code | Description | Quantity |
|---|---|---|
| A | Wood dowel Ø8*20mm | 40pcs |
| B | Three in one bolts Ø6*32mm | 24pcs |
| C | Three in one locks Ø14.5*9.5mm | 24pcs |
| D | Head bolt M6 x 30mm | 1pc |
| E | Allen key K4mm | 1pc |
| F | Damping hinge | 4sets (24pcs) |
| H | Scissor bud learns | 2pcs |
| I | Head bolt M6 x 45mm | 12pcs |
| J | Washer | 10pcs |
| K | Handle | 2pcs |
| L1 | Handle screw Ø5/32*28mm | 6pcs |
| M | Support piece | 1pc |
| N | Plastic Canopy Ø10x10mm | 4pcs |
| O | Round head screw Ø8xØ4*50mm | 4pcs |
| P | Anti fall Hardware | 2sets |
| R | Bracket | 1pc |
| (No code listed, but shown in diagram) | Round head screw Ø6xØ3*12mm | 2pcs |
Assembly Steps
STEP: 1
Attach Side Panel (L) (1) and Side Panel (R) (2) to the Frame Bottom (3) using Four (4) Three in one bolts (B).
STEP: 2
Attach part 4 to part 3 using Allen key (E), Head bolt M6 x 30mm (D), Support piece (M), and Head bolt M6 x 45mm (I) (2pcs). Attach part 7 to the assembly using Allen key (E), Head bolt M6 x 30mm (D), and Support piece (M).
STEP: 3
Assemble the main frame. Connect parts 1, 2, 3, 5, 6, 7, and 8 using Wood dowels (A) (16pcs), Washers (J) (10pcs), and Three in one locks (C) (4pcs).
STEP: 4
Prepare parts 16, 17, 20, and 21. Attach Three in one bolts (B) to parts 16 (x2), 17 (x2), 20, and 21 as indicated.
STEP: 5
Assemble drawer components. Connect parts 16, 17, 18, and 19 using Wood dowels (A) (16pcs) and Three in one locks (C) (8pcs). This assembly is done twice (X 2).
STEP: 6
Attach the assembled drawer components to the cabinet doors. Attach Door Cabinet (L) (part 20) and Door Cabinet (R) (part 21) to the corresponding assemblies using Three in one locks (C) (8pcs), Wood dowels (A) (8pcs), and Damping hinges (F) (4 sets).
STEP: 7
Install the doors onto the main cabinet frame. Attach the doors (parts 20 and 21) using Damping hinges (F) and Scissor bud learns (H). Use Head bolt M6 x 45mm (L1) (2pcs) for attachment.
STEP: 8
Assemble the drawer box. Attach parts 11, 12, 13, 14, and 15 using Three in one bolts (B) (4pcs), Handle (K) (2pcs), Round head screw Ø8xØ4*50mm (O) (4pcs), Three in one locks (C) (4pcs), Handle screw Ø5/32*28mm (L1) (4pcs), and Anti fall Hardware (P) (4pcs).
STEP: 9
Assemble the drawer internal dividers. Insert Vertical learning Compartment (9) and Drevent Studing (10) into the designated slots.
STEP: 10
Attach the drawer front. Attach the drawer face (part 15) to the assembled drawer box. Use Bracket (N) (1pc) and Round head screw Ø6xØ3*12mm (R) (2pcs) for attachment.
STEP: 11
Insert the assembled drawer into the cabinet. The diagram shows the drawer slides engaging with the cabinet runners.
STEP: 12
Secure the vanity to the wall for safety. Use the Anti fall Hardware (P) (2 sets) for wall mounting.
STEP: 13
Install the sink (Lavabo - part 22) onto the cabinet. Use silicone glue (not included) for installation. Allow 24 hours for the glue to set.
*Silicone glue is not included in the package to comply with safety regulations in certain shipping conditions.
Hinge Adjustments
This section provides detailed instructions on how to adjust the cabinet doors using the hinges:
Sideways / Tilt Adjustment
Turn the screw clockwise to move the door further away from the side of the cabinet. Turn anticlockwise to move the door closer to the side of the cabinet.
Height Adjustment
While supporting the weight of the door, turn the screws clockwise to move the door up. Turn anticlockwise to move the door down.
Forward and Back Adjustment
This adjustment is typically made by turning a screw on the hinge arm that controls the depth of the door relative to the cabinet frame.
