APC MONDO PLUS

Description

The APC Automation Systems ® Mondo+Plus is a standalone access control keypad with a Swipe card reader as well as control by APP from anywhere in the world. Both Fail Secure and Fail Safe locks can be used and also allow the integration of exit buttons and allow the user to generate a temporary code remotely through the APP.

Features

Specifications

Wiring Output

Indicators

Installation

• Fix the mounting plate as per the two holes (A and C) on the plate to the surface in which the keypad will be installed.
• Feed the keypad cable through the hole B insuring that any unused wires are isolated from one another.
• Fit the keypad to the mounting plate and fix in place using the phillips screw underneath.

Diagram shows a mounting plate with holes A and C, a cable entry hole B, and dimensions for the keypad (142mm height, 48mm width, 22mm depth). It also depicts wall anchors, self-tapping screws, a screwdriver, and a master card. A separate small diagram shows a Diode 1N4004 for relay circuit protection.

Programming

Quick Setup for Automatic Gates

To set the relay time to ONE second: Enter * 1 2 3 4 5 6 # 4 1 #

To add your PIN code: Enter * 1 2 3 4 5 6 # 9 4 digits code #

APC-SG802-AC Typhoon • APC-SG1600-AC Tsunami • APC-SG3000-AC Tornado

Diagram shows the keypad terminals: ONE, CL, OP, PE, PE, GND, COM, 18V. Connections are shown from a power supply (Red to +18V, Black to GND, Blue to ONE) to these terminals. A note indicates "Relay time should be set to ONE seconds".

APC-P450S Proteous 450 Sprint • APC-P500 Proteous 500

Diagram shows the keypad connected to a "POWER CONVERTOR" with inputs for DC POWER INPUT and outputs for Red (E1 +V DC), Black (E2 COM), and Brown (J9 COM). Notes indicate "Relay time should be set to ONE seconds" and specific connections for gate opening (J1 Start for Full Gate, J2 P.Start for Pedestrian Gate).

APC-CBSW24 Swing Gate System

Diagram shows the keypad connected to a "POWER CONVERTOR". Power supply wires (Red to +V, Black to -V) connect to the converter. Output wires from the converter (Brown to GND, Blue to O/S/C or Open/Close Input) connect to the gate system terminals (PB1, PB2). Notes indicate "Relay time should be set to ONE seconds" and specific connections for gate opening (PB2 for Double Gate, PB1 for Single/Pedestrian Gate).

All Other Automatic Gate Systems

General wiring diagram for a 12-18V DC power supply. Red wire connects to Positive, Black wire to Negative. Brown wire connects to "Common for O/S/C or Open/Close Input", and Blue wire connects to "O/S/C or Open/Close Input". A note indicates "Relay time should be set to ONE seconds".

Quick Setup for Electric Striker

To set the relay time to FIVE seconds: Enter * 1 2 3 4 5 6 # 4 5 #

To add your PIN code: Enter * 1 2 3 4 5 6 # 9 4 digits code #

Connection to Electric Striker (Fail Secure Type)

Diagram shows the keypad connected to a power supply (Negative: Black & Brown, Positive: Red) and the electric striker (Blue wire). A note states: "Power supply voltage must be suitable according to the electric strikers voltage and amperage requirements and must be within the keypads working parameter of 12-18 V DC." A note also indicates "Relay time should be set to the nominated unlocking time".

Connection to Electric Striker (Fail Safe Type)

Diagram shows the keypad connected to a power supply (Negative: Black & Brown, Positive: Red) and the electric striker (Grey wire). A note states: "Power supply voltage must be suitable according to the electric strikers voltage and amperage requirements and must be within the keypads working parameter of 12-18 V DC." A note also indicates "Relay time should be set to the nominated unlocking time".

Exit Button Connection

Diagram shows the keypad connected to a power supply (Negative: Black, Positive: Red) and the exit button (Yellow wire).

Data Backup & Wiegand Connection

Data Backup Mode

1. Set the device to receive data into Data Input Mode: * Master code # 71 #
2. Set the device to send data into Data Output Mode: * Master code # 70 #

If successful, the LED will flash green during the process then return to LED red after completion.

Default factory master code is 123456

Wiegand Connection

Diagram shows power supply connections (Negative: Black, Positive: Red) and Wiegand output connections (D0 Green, D1 White) for a Wiegand Reader.

APP Configuration

APP Install and Registration (All Users)

1. Download Tuya Smart from the APP Store on your Android/Apple Device.
2. Open the App and register an account, ensuring you select "Australia" as the country.
3. Login after registration. Note: Each user must register their own account.

Scan QR code to download APP or search TuyaSmart to download APP.

QR codes are present in the original document for app download.

APP Preparation (Home Owners Device)

1. Go to "Me"
2. Go to "Home Management"
3. Select "My Home..."

Steps to Name and Set Home Location:

1. Name the home
2. Set the Location
3. Deselect ALL the rooms except the one where the indoor monitor is installed.
4. Press Save

Screenshots show the app interface for navigating to "Me", "Home Management", and "My Home", followed by screens for entering home details like name, location, and room selection.

Adding the Keypad to the Administrator (Home Owners) Device

1. Open APP and Press Add Device.
2. Set the Keypad into Wi-Fi Pairing state.
3. Click Auto Scan. Ensure Wi-Fi and Bluetooth are ON.
4. Once the Mondo has been found, press Next.
5. Enter the Wi-Fi password.
6. Final Configuration.

Default factory master code is 123456

Screenshots illustrate the process: tapping 'Add Device', entering Wi-Fi pairing mode on the keypad (indicated by master code entry), the app scanning for devices, entering Wi-Fi credentials, and the connection progress.

User Management via App

Sharing with another User (Administrator/Ordinary Member)

Note: The member that you shared to must be registered to Tuya App First.

1. Go into the APP and select the Keypad.
2. Press the Member manage option.
3. Select the user type: Administrator or Ordinary Member.
4. Select the '+' icon.
5. Add user details (Tuya account details) and then press Next.
6. An invitation will be sent to the user.

Screenshots show the app interface for selecting a device, accessing member management, choosing user type, adding user details, and confirming the invitation.

Manage Members

The Owner (Super Master) can decide effective time (Permanent or Limited) for the members.

1. Press the Member manage option.
2. Select the member to manage.
3. Select the Effective time.
4. Customize the effective time and Save.
5. Effective time will be displayed on the member account.

To Delete a User:

1. Press the Member manage option.
2. Select the member to manage.
3. Select Delete user.

Screenshots illustrate managing members, setting permanent or limited effective times with start/end dates and times, and the process of deleting a user.

ADD Users PINCODE via APP support

You can add a Pin code by desired number or generate a random number. The number can be copied and forwarded to the user.

1. Press the Member manage option.
2. Select the member.
3. Select ADD Code.
4. Input 6 digits code and code name. Click Save.

Screenshots show the app interface for adding a PIN code, including options for manual input or random generation, and saving the code.

ADD Users Card via APP support

You can add a swipe Card via App support with the following procedure. The swipe card must be presented near the keypad during this process.

1. Press the Member manage option.
2. Select the member.
3. Select ADD Card.
4. Click ON Start ADD.
5. Keep the Swipe Tag near the reader.
6. Card Add success page will appear once the reader is detected.

Screenshots illustrate the process of adding a card, including starting the process, presenting the card to the reader, and confirmation of success.

Delete users pin code/ Card

Using the same process, you can delete CODE or Card from the user.

1. Press the Member manage option.
2. Select the member.
3. Select the CODE/CARD to delete.
4. Select Delete CODE/CARD.

Screenshots show the interface for selecting a user, then choosing to delete either a code or a card associated with that user.

Temporary Codes

Temporary Codes can be created or randomly generated using the APP and can be shared with guests/Users via WhatsApp, Skype, Emails, and WeChat.

Two types of Temporary code can be created: CYCLICITY and ONCE.

• CYCLICITY: Code can be created for a particular period, particular day, and Particular Time. For example, Valid at 9:00 am - 5:00 pm every Monday-Friday during May-August.
• ONCE: One-time Code can be created, valid for 6 hours and can only be used Once.

CYCLICITY Temporary Code Creation

1. Press on temporary code.
2. Select cyclicity and fill the details and save.
3. Temporary code is created.
4. Pin code can be shared by clicking on the share button.

Screenshots show the app interface for creating a cyclic temporary code, setting the time period, days, and times, and then sharing the generated code.

ONCE Temporary Code Creation

1. Press on temporary code.
2. Select Once and fill the code name and click on save offline code.
3. Temporary code is created.
4. Pin code can be shared by clicking on the share button.

Note: One-time Code can be created, valid for 6 hours and can only be used Once.

Screenshots show the app interface for creating a one-time temporary code, setting its validity, and then sharing the generated code.

Edit Temporary Code

Temporary code can be deleted, edited or renamed in the valid period.

1. Press on temporary code then Log record.
2. Select the log record you desire to change.
3. Select Delete/ Edit/Rename.

Screenshots illustrate accessing the log record of temporary codes and options to delete, edit, or rename them.

Settings

Timer/ Door keep Open

1. Press on settings.
2. Select Door keep open.
3. Turn ON Door Keep Open and Customize open time.
4. Can add one more open period.
5. Details can be seen in the highlighted box.

Screenshots show the app interface for configuring the "Door keep open" feature, including setting custom time periods.

Detailed Settings Explanation

• Remote unlock setting: Default is ON. Once turned OFF, all mobile users will not be able to access the lock by APP.
• Permission setting: Default is Permission all. Can be set to Permission admin only.
• Passage set: Default is Public. All mobile users have the passage permission. Once turned OFF, passage permission can be given to specific mobile users.
• Automatic Lock: Default is ON. Automatic Lock ON: Pulse Mode; Automatic Lock OFF: Latch Mode.
• Auto lock time: Default is 5 seconds. It can be set from 0~100 seconds.
• Alarm time: Default is 1 minute. It can be set from 1~3 minutes.
• Doorbell volume: It can set device buzzer volume to Mute, Low, Middle, and High.

Log (including open History and Alarms)

Log open history and Alarms can be viewed by clicking on the Notification icon as shown in the picture.

Screenshots show the app interface for accessing the log history and alarm notifications.

Remove Device & Reset Wifi Blinding

Note:

• Disconnect is just removing the device from the APP. The users (card/ fingerprint/code) are still retained. (If Super Master is Disconnected, all other members will have no access to the device).
• Disconnect and wipe data is unbinding the device and resetting WiFi. (This device can be connected by other new users).

Method to reset the WiFi: Enter * {Master Code} # 9 {Master Code} #

(To change the Master Code, please refer to another user manual)

Screenshots show the device settings menu with options for disconnecting and wiping data, and the interface for resetting WiFi.

APC WARRANTY

APC warrants the original purchasers or the APC system for a period of twelve months from the date of purchase (not installation), the product shall be free of defects in materials and workmanship under normal use.

During the warranty period, APC shall, as its option, repair or replace any defective product upon return of the product to its factory, at no charge for labour and materials.

Any replacement and/or repaired parts are warranted for the remainder of the original warranty.

The original owner must promptly notify APC in writing that there is a defect in material or workmanship. Such written notice must be received in all events prior to expiration of the warranty.

International Warranty

APC shall not be responsible for any freight fees, taxes or customs fees.

Warranty Procedure

To obtain service under this warranty, AND AFTER CONTACTING APC, please return the item(s) in question to the point of purchase.

All authorized distributors and dealers have a warranty program; anyone returning goods to APC must first obtain an authorization number. APC will not accept any shipment for which prior authorization has not been used.

Conditions to Void Warranty

This warranty applies only to defects in parts and workmanship relating to normal use. It does not cover:

• Damage incurred in shipping or handling
• Damage caused by disaster such as fire, flood, wind, earthquake or lightning
• Damage due to causes beyond the control of APC such as excessive voltage, mechanical shock or water damage
• Damage caused by unauthorized attachment, alterations, modifications, or foreign objects.
• Damage caused by peripherals (unless such peripherals were supplied by APC)
• Defects caused by failure to provide a suitable installation environment for the products
• Damage caused by usage of the products for purpose other than those for which it was designed.
• Damage from improper maintenance
• Damage arising out of any other abuse, mishandling, and improper application of the products.

Under no circumstances shall APC be liable for any special, incidental, or consequential damages based upon breach of warranty, breach of contract, negligence, strict liability, or any other legal theory. Such damages include, loss of profits, loss of the product or any associated equipment, cost of capital, cost of substitute or replacement equipment, facilities or services, down time, purchaser's time, the claims of third parties, including customers, and injury to property.

Disclaimer of Warranties

This warranty contains the entire warranty and shall be in lieu of any and all other warranties, whether expressed or implied (including all implied warranties of merchantability or fitness for a particular purpose). And of all other obligations or purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product.

Out of Warranty Repairs

APC will, at its option, repair or replace out-of-warranty products which are returned to its factory according to the following conditions. Anyone returning goods to APC must first obtain an authorization number. APC will not accept any shipment whatsoever for which prior authorization has not been obtained. Products which APC determines to be repairable will be repaired and returned. A set fee, which APC has predetermined and which may be revised from time to time, will be charged for each unit repaired. Products which APC determines not repairable will be replaced by the nearest equivalent product available at that time. The current market price for the replacement product will be charged for each replacement unit.