Philips Soundbar Série 8000 TAB8505

Important Safety Information

Please read and understand all instructions before using this product. Failure to follow these instructions may void the warranty.

• Risk of electric shock or fire: Do not expose the product or accessories to rain or water. Keep away from open flames and heat sources. Ensure the power cord is easily accessible. Do not expose batteries to excessive heat. Disconnect the product from the mains during thunderstorms. Always pull the plug, not the cord, when disconnecting. Use only in tropical/temperate climates.
• Risk of short circuit or fire: Verify the power supply voltage matches the product's rating.
• Risk of injury or product damage: For wall mounting, ensure secure installation. Handle glass components with care. Do not install in confined spaces; allow ventilation space.
• Risk of contamination: Do not mix batteries. Replace with identical or equivalent types. Remove batteries if the remote control will not be used for a long time. Dispose of batteries properly. Keep batteries away from children.

Caring for your product

Use a microfiber cloth for cleaning.

Environmental Protection

This product is made with high-quality materials that can be recycled. Dispose of electrical and electronic products and batteries separately according to local regulations.

Compliance

This product complies with European Community radio interference requirements.

Getting Help and Support

Visit www.philips.com/support for:

• Downloading manuals and quick start guides
• Video tutorials
• FAQs
• Email support
• Chat with a support representative

Note your product model and serial number before contacting support.

FCC and IC Statement (USA and Canada only)

This equipment has been tested and found to comply with Class B digital device limits. It generates, uses, and can radiate radio frequency energy. If not installed and used according to instructions, it may cause harmful interference to radio communications. If interference occurs, try repositioning the antenna, increasing distance, or consulting a dealer or experienced technician.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to two conditions: (1) the device may not cause interference, and (2) the device must accept any interference, including interference that may cause undesired operation.

FCC and IC Warning: Maintain a minimum distance of 20 cm between the radiator and your body. Unauthorized changes may void the user's right to operate the equipment.

Your Soundbar

What's in the box

Check and identify the items in the package:

• 1 Soundbar
• 1 Wireless Subwoofer
• 1 Remote control
• 4 Power cords*
• 1 Wall mounting kit (2 brackets, 2 screws, 2 wall plugs)
• 1 Quick start guide / Warranty card / Safety sheet / Wall mounting template

*Power cord types vary by region.

Main Unit

The main unit features the following controls:

1. - (Volume): Decreases volume.
2. + (Volume): Increases volume.
3. II (Play/Pause): Starts, pauses, or resumes playback.
4. (Source)/Bluetooth Pairing: Selects an input source. Press and hold to activate Bluetooth pairing mode or disconnect the currently paired Bluetooth device.
5. (Standby-On): Powers the unit on or off.

Display Panel

• Wi-Fi Indicator (Yellow):
• Flashing: Wi-Fi access point mode (AP) or Wi-Fi Protected Setup (WPS) pairing mode.
• Double flashing: Wi-Fi configuration mode.
• Solid: Connected / Paired.

Connectors

• USB: Audio input from a USB storage device.
• AUX: Audio input (3.5 mm jack).
• OPTICAL: Optical audio output connection.
• (Wi-Fi Configuration): Activates Wi-Fi configuration for Play-Fi. Press and hold for 3 seconds for WPS mode, or 8 seconds for AP mode.
• HDMI OUT (eARC/ARC): Connects to the TV's HDMI input.
• HDMI 1 / HDMI 2: Connects to the TV's HDMI input.
• AC~: Power connection.
• Wall mount slot

Wireless Subwoofer

• AC~: Power connection.
• Pair Button: Press to enter subwoofer pairing mode.
• Subwoofer Indicator: Shows pairing status.
• Fast flashing: Subwoofer in pairing mode.
• Solid: Connected / Paired.
• Slow flashing: Connection / Pairing failed.

Remote Control

The supplied remote control allows you to operate the unit from a distance.

• (Standby-On): Powers the unit on or off.
• (Source): Selects an input source. Press and hold to activate Bluetooth pairing or disconnect.
• (Dolby): Activates or deactivates Dolby mode.
• (Mute): Mutes or unmutes the volume.
• II (Play/Pause): Starts, pauses, or resumes playback.
• (Arrows): Navigate menus, skip tracks.
• (MENU): Opens the configuration menu.
• (Return): Returns to the previous menu or exits the menu. Press and hold for 10 seconds to reset the Wi-Fi module to factory settings.
• +/- (Volume - Soundbar): Adjusts the soundbar volume.
• ((Sub)) +/- (Volume - Subwoofer): Adjusts the subwoofer volume.

Preparing the Remote Control

The remote control comes with a pre-installed CR2025 lithium battery. Remove the protective tab to activate the battery.

Replacing the Remote Control Battery

Requires one 3V CR2025 lithium battery.

1. Insert a tool into the groove on the battery cover and turn counter-clockwise to unlock.
2. Remove the old battery, insert the new CR2025 battery, observing correct polarity (+/-).
3. Turn the cover clockwise to lock it.

Battery Precautions:

• Remove the battery if the remote will not be used for over a month.
• If the battery leaks, clean the compartment and replace the battery.
• Use only the specified battery type.
• Do not heat or disassemble batteries.
• Do not dispose of batteries in fire or water.
• Do not transport or store batteries with metal objects.
• Do not recharge non-rechargeable batteries.

Positioning

Place the subwoofer at least 1 meter (3 feet) from the soundbar and 10 cm (4 inches) from the wall. For best results, position as shown.

Wall Mounting

Important

• Incorrect wall mounting can cause accidents or damage. If you have questions, contact customer service.
• Ensure the wall can support the soundbar's weight.
• Use appropriate screws and wall plugs for your wall type.
• Check if the USB port on the back of the soundbar is connected to a USB device. If it obstructs mounting, use a different USB device.

Mounting Instructions

1. Drill two parallel holes in the wall (3-8 mm diameter, depending on wall type). The distance between the holes should be:
• 856 mm / 33.7" (TAB8405 / TAB8505)
• 1017 mm / 40" (TAB8805)
• 1076 mm / 42" (TAB8905)
2. Use the provided wall mounting template to help position the holes.
3. Insert wall plugs and screws into the holes.
4. Remove the screws (4) from the main unit.
5. Attach the wall brackets (2) to the main unit using the removed screws.
6. Hang the soundbar onto the mounting screws.

Suggested Wall Mounting Height: Install the TV first. Then mount the soundbar 50 mm (2.0") from the bottom of the TV.

Connections

This section guides you through connecting your soundbar to your TV and other devices.

Dolby Atmos®

Dolby Atmos offers an immersive 3D sound experience. For more information, visit dolby.com/technologies/dolby-atmos.

Dolby Atmos is available only in HDMI ARC/eARC mode. Refer to "HDMI Connection" for details.

1. Your TV must support Dolby Atmos via HDMI 1 / HDMI 2 / HDMI ARC.
2. Select "No encoding" for the digital audio bitstream output of the connected external device (e.g., DVD or Blu-ray player, TV).
3. The soundbar will display DOLBY ATMOS / DOLBY AUDIO / PCM AUDIO / DOLBY SURROUND when Dolby Atmos / Dolby Digital / PCM format is selected.

Note: For the full Dolby Atmos experience, connect via HDMI 2.0 cable. Other connections may limit Dolby features.

HDMI Connection

Some 4K HDR TVs require HDMI input or picture settings to be adjusted for HDR content.

Option 1: eARC/ARC (Audio Return Channel)

Your soundbar supports HDMI with Audio Return Channel (eARC/ARC). If your TV supports HDMI ARC, you can hear its sound through your soundbar using a single HDMI cable.

1. On your TV, enable HDMI-CEC functions. Consult your TV's manual for details.
2. Use a high-speed HDMI cable to connect the HDMI OUT (eARC/ARC)-TO TV connector on your soundbar to the TV's HDMI ARC connector.

Note: Your TV's HDMI-CEC and ARC functions must be enabled. The setup method may vary by TV. Ensure you use HDMI cables that support ARC.

Option 2: Standard HDMI

If your TV does not support HDMI ARC, connect your soundbar via a standard HDMI connection.

1. Use an HDMI cable (included) to connect the soundbar's HDMI IN (1 or 2) to your external devices (e.g., game consoles, DVD or Blu-ray players).
2. Use an HDMI cable (included) to connect the soundbar's HDMI OUT (eARC/ARC) to your TV's HDMI IN port.

Optical Connection

Use an optical cable to connect the OPTICAL OUT port on your TV or other device to the OPTICAL port on your soundbar. The digital optical connector may be marked SPDIF or SPDIF OUT.

AUX Connection

a. Using a 3.5 mm to 3.5 mm audio cable: Connect the TV's headphone jack to the AUX jack on the unit.

b. Using an RCA to 3.5 mm audio cable: Connect the TV's audio output jacks to the AUX jack on the unit.

Power Connection

Before connecting the power cord, ensure all other connections are complete.

Risk of product damage: Verify the mains voltage matches the voltage printed on the back or bottom of the unit.

1. Connect the power cord to the unit's AC~ socket and then to a mains socket.
2. Connect the power cord to the subwoofer's AC~ socket and then to a mains socket.

Pairing with the Subwoofer

Automatic Pairing

Connect the soundbar and subwoofer to their mains sockets. Press the unit or remote control to turn on the device. The subwoofer and soundbar will pair automatically.

Manual Pairing

If you do not hear sound from the wireless subwoofer, manually pair it.

1. Disconnect both devices from the mains sockets, then reconnect them after 3 minutes.
2. Press the Pair button on the back of the subwoofer for 5 seconds. The subwoofer's pairing indicator will flash rapidly.
3. Press and hold the standby button on the unit or remote control to put the unit into ECO STANDBY mode.
4. Press the unit or remote control button to turn on the unit. The subwoofer's pairing indicator will become solid once the operation is successful.
5. If the pairing indicator still flashes, repeat steps 1 to 3.

Tips:

• The subwoofer should be within 6m (approx. 20 feet) of the soundbar in an unobstructed area.
• Remove any objects between the subwoofer and the soundbar.
• If wireless connection fails again, check for conflicts or strong interference from other electronic devices and repeat the procedures.

Wi-Fi Connection (Wireless)

(For iOS and Android versions.)

By connecting this device and mobile phones or tablets (such as iPad, iPhone, iPod touch, Android phones, etc.) to the same Wi-Fi network, you can use the Philips Sound app with DTS Play-Fi to control audio playback on the soundbar.

1. Connect your phone or tablet to the same Wi-Fi network as your soundbar.
2. Download and install the Philips Sound app with DTS Play-Fi on your phone or tablet.
3. Press and hold the Wi-Fi button on the unit for 8 seconds to initiate Wi-Fi connection. Wait for the speaker to emit a second tone, then release the button.
4. Wait for the Wi-Fi indicator on the front panel to change from fast flashing to slow pulsing. A slow flash indicates the speaker is in Wi-Fi configuration mode.
5. Launch the Philips Sound app with DTS Play-Fi and follow the app's instructions to connect the product to your Wi-Fi network.

Note for iOS version: The Wi-Fi network used by the iPhone must temporarily switch to the Play-Fi device's access point. Then, restart the Philips Sound app to complete the product's Wi-Fi configuration.

AirPlay Configuration: Use AirPlay to configure the Wi-Fi connection for iOS devices (iOS 7 or later) and the soundbar.

1. iOS Device: Go to Settings > Wi-Fi > select your home network [Play-Fi Device (xxxxxx)].
2. Return to the Philips Sound app to continue configuration.

Once the Wi-Fi connection is established, the Wi-Fi indicator will stop flashing and become solid. You can then control the product from any smartphone or tablet on the same network.

When using the app for music playback, the display will show PLAY-FI.

You can change the device name after the connection is established.

This product may perform a software update once the connection is established. Perform the upgrade to the latest software during initial setup. Do not disconnect the speaker, turn off your device, or leave the network during the update.

Using your Soundbar

Before you start

• Complete the necessary connections as described in the quick start guide and this manual.
• Switch the soundbar to the appropriate source for the connected devices.

Power On and Off

When first connected to the mains, the unit remains in standby. The STANDBY indicator lights up white.

• On: Press the button once. The indicator follows the source status. Wi-Fi is always active and supports Play-Fi and AirPlay2.
• Eco Standby: Press and hold the button for 5 seconds. Wi-Fi is deactivated. The product enters low power consumption mode. System restart will take longer.

Automatic Standby

The unit automatically enters standby after approximately 15 minutes if the TV or external device is disconnected, or if the playback function (USB, BT, or Play-Fi) is paused or stopped.

Selecting Modes

1. Press the button on the unit or remote control multiple times to select the mode: AUX, OPTICAL, HDMI eARC/ARC, HDMI 1, HDMI 2, BT, or USB. The selected mode is indicated on the display.
2. Play-Fi is not a source option; it must be controlled directly via the app.

Adjusting the Volume

Soundbar Volume

1. Press +/- (Volume) to increase or decrease the volume level.
2. Press Mute to silence the sound. Press Mute again or Vol+/Vol- to restore sound.

Subwoofer Volume

1. Press ((Sub)) +/- to increase or decrease the subwoofer volume level.

Dolby Sound Mode

Experience immersive audio with Dolby sound modes.

1. Press the Dolby button on the remote control to activate or deactivate Dolby mode.
• On: Creates a Dolby listening experience.
• Off: Stereo two-channel sound. Ideal for music listening.

Resetting to Factory Settings

• In standby mode: Press the buttons on the remote control sequentially; the screen will display "RESET" to reset the host's factory default settings.
• With the unit powered on: Press and hold the button until the screen displays "RESET" to reset the Wi-Fi module to factory default settings.

Configuration Menu

The unit allows you to configure advanced settings for a better experience.

1. Press the (MENU) button on the remote control to open the menu.
2. Select content using ▼/▲ (Up/Down) on the remote control.
3. Press ■ (Enter) to confirm your selection.
4. Modify initial values for each setting using the arrow keys (Left/Right).
5. Press ■ (Enter) to confirm your selection.

Display Settings

• EQ: Selects the equalizer effect (EG).
• BASS: Adjusts bass levels.
• TREB: Adjusts treble levels.
• AV SYNC: Adjusts audio delay.
• CENT (CENTER) (TAB8805, TAB8905 only): Adjusts center channel volume.
• TOP (TAB8905 only): Adjusts top channel volume.
• DIM: Adjusts display brightness.
• DISPLAY: Automatically turns off the display (except Wi-Fi indicator) after 3 seconds of inactivity.
• KEY TONE: Activates or deactivates the touch key sound.

Bluetooth Usage

Bluetooth allows you to connect your soundbar to a Bluetooth device (e.g., iPad, iPhone, iPod touch, Android phone, or laptop) to play audio files stored on the device through the soundbar's speakers.

1. Press the button on the unit or remote control multiple times to set the soundbar to Bluetooth mode. "NO BT" will be displayed.
2. On your Bluetooth device, activate Bluetooth, search for and select "Philips TAB8505" to start the connection (refer to your Bluetooth device's manual for instructions on activating Bluetooth).
3. Wait until you hear the voice prompt from the soundbar. If the connection is successful, "BT" will be indicated on the display.
4. Select and play audio files or music on your Bluetooth device. If you receive a call during playback, music playback will be suspended and resume after the call.
5. If your Bluetooth device supports the AVRCP profile, you can use the remote control's / buttons to skip to a track or press II to pause or resume playback.
6. To exit Bluetooth mode, select another source. When you return to Bluetooth mode, the connection remains active. To connect your soundbar to another Bluetooth device, press and hold the button on the remote control to disconnect the currently connected Bluetooth device.

Note: Bluetooth devices supporting A2DP and AVRCP profiles with Bluetooth version 4.2 + EDR are recommended. The maximum operating range between the soundbar and a Bluetooth device is approximately 10 meters (30 feet). Compatibility with all Bluetooth devices is not guaranteed. Music streaming may be interrupted by obstacles between the device and the soundbar, such as walls, metal casings, or other devices using the same frequency.

Using AUX / OPTICAL / HDMI ARC

Ensure the device is connected to the TV or audio device.

1. Press the button on the unit or remote control multiple times to select the AUX, OPTICAL, HDMI eARC/ARC, HDMI 1, or HDMI 2 mode.
2. Use your audio device directly for playback functions.
3. Press the VOL +/- buttons to adjust the volume.

Tip: In OPTICAL / HDMI ARC mode, if there is no sound and the status indicator flashes, you may need to enable the digital audio output (PCM or Dolby Digital Signal) on your source device (e.g., TV, DVD player, Blu-ray player). The unit may not be able to decode all digital audio formats from the input source, resulting in muted sound. This is not a malfunction. Ensure the audio output setting of your source device is set to PCM or Dolby Digital (refer to your source device's manual for details) when using HDMI 1 / HDMI 2 / HDMI ARC / Optical input.

In HDMI mode, when the Dolby Atmos audio format is applied, the soundbar display will show DOLBY ATMOS. When the Dolby Digital audio format is applied, if surround sound is active, the display will show DOLBY SURROUND; if surround sound is inactive, it will show DOLBY AUDIO. When the PCM audio format is applied, the soundbar display will show PCM AUDIO. If the applied audio formats are neither PCM nor Dolby Digital, no sound will be emitted, and the display will show ERROR.

USB Usage

Enjoy audio from a USB storage device, such as an MP3 player or USB flash drive.

1. Insert the USB device.
2. Press the button on the unit or remote control multiple times to set the soundbar to USB mode.
3. During playback:
• Button: Starts, pauses, or resumes playback.
• / Skips to the previous or next track.

Tips:

• This product may not be compatible with certain types of USB storage devices.
• If you use a USB extension cable, USB hub, or USB card reader, the USB storage device may not be recognized.
• Do not remove the USB storage device during file playback.
• The unit may recognize USB devices with up to 32 GB of memory.
• This unit can play MP3 / WAV / FLAC formats.
• USB port specifications: 5V 500 mA.

Spotify Listening

Use your phone, tablet, or computer to remotely control Spotify. Visit spotify.com/connect to learn how.

Firmware Update

For the best features and support, update your product to the latest firmware version.

Option 1: Firmware update via Philips Sound app

The firmware of the MCU and DSP can be upgraded to its latest version via the Philips Sound app with DTS Play-Fi. Go to the settings menu and select the PS Fine Tune option to check. If an upgrade is available, you can tap the upgrade icon to apply it automatically. Once connected to Wi-Fi, this product can receive firmware updates wirelessly. Always update to the latest firmware version to improve product performance.

Option 2: Firmware update via USB

1. Check for a new firmware version at www.philips.com/support. Search for your model and click on "Software & drivers".
2. Download the firmware to a USB flash drive.
3. Follow the firmware upgrade instructions.

Product Specifications

Subwoofer

• Power: 100-240 V~, 50-60 Hz
• Output Power: 80 W
• Power Consumption: 20 W
• Standby Power Consumption: < 0.5 W
• Frequency Response: 35 Hz – 150 Hz
• Impedance: 4 Ω
• Dimensions (W x H x D): 120 x 403 x 300 mm
• Weight: 4.8 kg
• Operating Temperature: 0°C - 45°C

Bluetooth / Wireless

• Bluetooth Profiles: A2DP, AVRCP
• Bluetooth Version: 4.2 + EDR
• Frequency Range / Output Power: 2400 MHz ~ 2483.5 MHz / ≤ 5 dBm
• 2.4G Radio Frequency Range / Output Power: 2400 MHz ~ 2483 MHz / ≤ 6 dBm

Supported Network

• Wi-Fi Radio Frequency Range: IEEE 802.11a/b/g/n/ac / Transmitted Radio Frequency Power
• Wi-Fi 2.4G: 2400 MHz ~ 2483.5 MHz / < 20 dBm
• Wi-Fi 5.1G: 5150 MHz ~ 5350 MHz / < 20 dBm
• Wi-Fi 5.8G: 5725 MHz ~ 5850 MHz / < 14 dBm

Main Unit

• Power: 100-240 V~ 50/60 Hz
• Output Power: 120 W
• Power Consumption: 25 W
• Standby Power Consumption: < 0.5 W
• USB: 5 V ⎓ 500 mA
• Frequency Response: 150 Hz – 20 KHz
• Audio Input Sensitivity: 500 mV
• Speaker Impedance: 2 x 8 Ω
• Dimensions (W x H x D): 900 x 57 x 110 mm
• Weight: 2.4 kg
• Operating Temperature: 0°C - 45°C

Remote Control

• Distance / Angle: 6 m / 30°
• Battery Type: CR2025

Supported Audio Formats

• HDMI eARC/ARC: Dolby Digital, Dolby Digital plus, Dolby True HD, Dolby Atmos®, LPCM 2 ch/M ch., Dolby MAT.
• HDMI IN1 / HDMI IN2: Dolby Digital, Dolby Digital plus, Dolby True HD, Dolby Atmos®, LPCM 2 ch/M ch., Dolby MAT.
• OPTICAL: Dolby Digital, Dolby Digital Plus, LPCM 2 channels
• BLUETOOTH: SBC
• USB: MP3 / WAV / FLAC
• Video: Video enhancement: 4K video transfer, Dolby Vision, HDR10, HDR10+

Troubleshooting

Warning

Risk of electric shock. Do not remove the product casing.

To maintain warranty validity, do not attempt to repair the product yourself. If you encounter problems, check the following points before seeking service. If the problem persists, get assistance at www.philips.com/support.

Main Unit

• Buttons not working: Disconnect the power for a few minutes, then reconnect.
• No power: Ensure the power cord is securely connected. Check if the power outlet is working. Press the standby button on the remote control or soundbar to turn on the soundbar.

Sound

• No sound from the soundbar: Connect the soundbar's audio cable to your TV or other devices. Separate audio connection is not needed if:
  • the soundbar and TV are connected via HDMI ARC, or
  • a device is connected to the soundbar's HDMI IN connector.
  Select the correct audio input source on the remote control. Check if the soundbar's sound is muted. Reset the product to factory settings.
• No sound from the wireless subwoofer: Manually connect the subwoofer to the main unit. Increase the volume. If no sound from a digital input, try setting the TV output to PCM or make a direct connection to your Blu-ray source. Some TVs do not transmit digital sound. Check if your TV's audio output is set to FIXED or STANDARD, not variable. If using Bluetooth, ensure your source device volume is up and not muted. If playback freezes and there is no sound in Wi-Fi mode, check your home network.
• Distorted or echoing sound: If streaming TV sound, mute the TV.
• Audio and video out of sync: Press to synchronize sound and video.

Bluetooth

• Device cannot connect to the soundbar: The device may not support the required Bluetooth profiles. Ensure Bluetooth is activated on your device. Re-pair the device. Ensure the device is correctly connected. The soundbar may already be connected to another Bluetooth device; disconnect the connected device and try again.
• Poor Bluetooth audio playback quality: Poor Bluetooth reception. Move the device closer to the soundbar or remove obstacles.
• Cannot find the Bluetooth name: Ensure Bluetooth is activated on your device. Re-pair the device with your Bluetooth device.

Wi-Fi

• Wi-Fi connection cannot be established: Check wireless local area network availability on the router. Move the Wi-Fi router closer to the device. Verify the password. Check WLAN function or restart the modem and Wi-Fi router.

Dolby Atmos

Cannot get specific Dolby Atmos effects: With non-HDMI connections (USB, Bluetooth, OPTICAL, or AUDIO IN), surround effects are limited. Refer to the "Dolby Atmos" section for how to achieve the best Dolby Atmos effects.

Play-Fi

• Cannot discover compatible Play-Fi devices: Ensure the device is connected to Wi-Fi.
• Cannot play music via Play-Fi: Some network services or content may become unavailable if the service provider terminates its service. If initial setup fails, close the Philips Sound app with DTS Play-Fi and restart it. If the speaker was set to stereo pairs or surround sound, it must be disconnected in the app before being used separately.

Remote Control Not Working

• Before pressing a playback control button, select the correct source first.
• Reduce the distance between the remote control and the unit.
• Insert the battery with polarities aligned as indicated. Replace batteries.
• Point the remote control directly at the sensor on the front of the unit.

Automatic Power Off

There is an automatic power-off function after 15 minutes, as required by the ERP II standard for energy saving. If the input signal level is too low, the unit will turn off automatically within 15 minutes. Please increase the volume of your external device.

Subwoofer in Standby or Indicator Not Lighting Up

Unplug the power cord from the mains socket and plug it back in after 3 minutes to reset the subwoofer.

Trademarks

dts Play-Fi: For DTS patents, visit http://patents.dts.com. Manufactured under license from DTS, Inc. DTS, Play-Fi, and the DTS Play-Fi logo are registered trademarks or trademarks of DTS, Inc. Wi-Fi CERTIFIED logo is a certification mark of the Wi-Fi Alliance®. Google, Google Play, and Chromecast built-in are trademarks of Google LLC. Works with Apple AirPlay: Requires iOS 11.4 or later. Use of the Works with Apple badge means an accessory has been designed to work specifically with the technology identified in the badge and has been certified by Apple Inc. trademarks. Apple® and AirPlay® are trademarks of Apple Inc. Spotify software is subject to third-party licenses: www.spotify.com/connect/third-party-licenses. HDMI, HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. Dolby Vision, Dolby Atmos, and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation. Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.