Bower Desk Mount Stand

Product Overview

A visual representation of the Bower Desk Mount Stand, featuring a central column clamped to a desk, supporting two adjustable arms. One arm holds a camera, and the other holds a light fixture. The stand is made of dark metal with articulated joints.

In the Box

• 360° Ball Head
• 3-section Extendable Arm
• 7in. Extension Column (optional use)
• 2-section Extendable Arm with 1/4 in. Mount
• Desk Mount (rubber lined)

Product Parts Introduction

1. Center Column: The main vertical support.
2. 2-section Extendable Arm: An adjustable arm with two segments.
3. 3-section Extendable Arm: An adjustable arm with three segments.
4. Desk Mount: The base clamp designed to attach to a desk, featuring rubber lining to protect surfaces.
5. 360° Ball Head: A versatile head for mounting devices, allowing full rotation.
6. 1/4 in. Mount: A standard mounting adapter with a 1/4 inch screw, also featuring a 3/8 inch screw on the bottom for larger equipment.
7. Screw Dial: Used for attaching and detaching components.
8. Locking Screw (arm position): Secures the position of an arm relative to the center column.
9. Locking Screw (arm joint): Secures the position of joints within an arm.

Installation

Step 1: Mounting the Center Column

Mount the Center Column with Desk Mount onto a table/desk. Rotate the knob until firmly attached. Do not over tighten.

Diagram Description: An illustration demonstrating the desk clamp base being attached to the edge of a table. A knob is shown being turned to secure the clamp. The inside of the mount is rubber lined to protect the table from damage.

Step 2: Attaching Center Column Extension

Attach the Center Column Extension by screwing it in. Screw until firmly attached, do not over tighten.

Diagram Description: An illustration showing an extension pole being screwed into the top of the center column.

Step 3: Attaching the 3-section Arm

Loosen the locking screw on the 3-section arm and insert it into the center column. Tighten the locking screw once the desired position is determined. Tighten firmly, but do not over tighten.

Diagram Description: An illustration depicting a 3-section adjustable arm being inserted into the center column and a locking screw being tightened to fix its position.

Step 4: Attaching the 2-section Arm

Loosen the locking screw on the 2-section arm and insert it into the center column. Tighten the locking screw once the desired position is determined. Tighten firmly, but do not over tighten.

Diagram Description: An illustration depicting a 2-section adjustable arm being inserted into the center column and a locking screw being tightened to fix its position.

Step 5: Removing Mounts

Remove the 360° Ball Head and 1/4 in. Mount adapter from the arms by unscrewing them. It is recommended that both mounts be removed to attach your devices to them.

Diagram Description: Two small illustrations: one shows a dial on a ball head being turned to loosen it, and the other shows a locking screw on a mounting adapter being turned to loosen it.

Step 6: Attaching Devices with 360° Ball Head

Tighten the dial on the 360° Ball Head so the metal ball is firmly set in an upright position. Screw the 360° Ball Head into the 1/4 in. screw thread on your device. Screw in firmly, but do not over tighten. Once securely attached to your device, attach it to the 1/4 in. screw on the arm by turning the dial underneath.

Diagram Description: Two illustrations: the first shows a device (e.g., camera) being screwed onto the 360° Ball Head. The second shows the 360° Ball Head assembly being attached to the end of an arm via its mounting screw and tightened with a dial.

Note: Other devices can be mounted onto the 360° Ball Head (phone mounts, microphones, LED lights, etc.).

Step 7: Attaching Devices with 1/4 in. Mount

Screw the 1/4 in. Mount adapter into the 1/4 in. screw thread on your device. Screw in firmly, but do not over tighten. Once securely attached to your device, attach it to the arm by inserting it inside the socket and turning the locking screw to securely attach.

Diagram Description: Two illustrations: the first shows a device (e.g., camera) being screwed onto the 1/4 in. Mount adapter. The second shows the 1/4 in. Mount adapter assembly being attached to the end of an arm via its socket and secured with a locking screw.

Note: Other devices can be mounted onto the 1/4 in. Mount adapter (phone mounts, cameras, microphones etc.).

Specifications

• Material: Aluminum
• Clamp Opening: 1.9 in. (50mm) maximum opening
• Clamp Height: 2.8 in. (71mm)
• Center Column Height: 27.7 in. (70cm)
• 2-section Arm Length: 19 in. (48cm) maximum, 10 in. (25cm) minimum
• 2-section Arm Weight Capacity: 6.6 lb. (3 kg) maximum
• 2-section Arm Weight: 1 lb. (467 g)
• 3-section Arm Length: 28 in. (71 cm) maximum, 10 in. (25cm) minimum
• 3-section Arm Weight Capacity: 3.3 lb. (1.5 kg) maximum
• 3-section Arm Weight: 1.3 lb. (602 g)
• Total Extension (both arms on center column): 48 in. (122cm) maximum, 12 in. (30cm) minimum
• Total Weight Capacity (both arms on center column): 9.9 lb. (4.5 kg) maximum (each arm holds a specific weight limit, see above)
• Product Size: 12 in. (30cm) width, 27.7 in. (70cm) height, 3.4 in. (8.6cm) depth
• Product Weight: 4lb (1858 g)