Owner's Manual for JH heater models including: JH-NR10-13W, Electric Infrared Radiant Wifi Panel Heater
Author: User Created Date: 5/26/2020 8:23:49 PM
File Info : application/pdf, 17 Pages, 1.45MB
DocumentDocumentINFRARED HEATER Quality Heating Wifi READ AND SAVE THESE INSTRUCTIONS Read all instructions carefully before setting up and operating this unit. This manual is designed to provide you with important information needed to setup, operate, maintain for your radiant heaters. Failure to follow these instructions may damage and/or impair its operation and void the warranty. 1. SAFETY PRECAUTIONS Health and fresh! This appliance is not intended for use by persons (including children) with reduced physical sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. WARNING: In order to avoid overheating, do not cover the heater. 1. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. 2. The heater must not be located immediately below a socket outlet. 3. Do not use the same socket together with other appliances, in case of current overload. Make sure the plug and socket good contact. 4. Please pull plugs out when power off. Do not pull wires by hands. 5. Please stop power immediately once heaters failure or wires are broken. Users can not repair heaters by themselves. Please contact authorized servicer for maintenance if heaters failure. 6. Radiant heater cannot be placed directly below the power outlet. 7. Radiant heater surface temperature is high, must be installed higher than 22 meters above ground. 8. Radiant heater surface cannot be covered and cannot hang objects on equipment. 9. The distance between back of radiant heater and roof should be larger than 150mmcannot place objects within 1000mm distance in front of radiant heater, the side should be kept at least 200mm away from the surrounding space. 10. Must cut off power and wait till equipment surface cool before cleaning, flushed by water is prohibited. 11. Users cannot repair the radiant heaterif equipment failure and need maintenance, please contact authorized servicer. 12. Do not install and use radiant heaters on areas occur with flammable 1 Health and fresh! explosiveeasy to shock. 13. Please do not insert any metal or foreign objects to inside of radiant heater, to avoid accident or personal injury. 14. Radiant heater panel surface with high temperature, the surface temperature can reach to >50~386touch is forbiddenbeware of scalding accident. 15. Do not splash water into radiant heater to avoid accidents. 2. FOREWORD Thank you for your trust and support in choosing the Infrared Heater, please read the instructions carefully before operating product. 3. INFRARED HEATER THEORY Far-infrared radiant heaters are produced by unique design and manufacturing technique. Using a specially coated aluminum panel, the heat generated by the heating element is transferred radiantly to people and objects with maximum efficiency. The heat radiated from the panel surface, is absorbed by people, walls, floors, and furniture etc., like sunshine. Infrared heating will not lead to air movement, making the air cleaner, as dust and particles are not disturbed and circulated. Traditional convection heating relies on air movement to distribute the heat. The air remains less humid, and gives you a sense of fresh, comfortable, warmth-similar to the warmth felt from the sun. 4. PERFORMANCE FEATURES Comfortable: No wind, light or odor will be caused during the running of this product, so the indoor air is clean without floating dust. Energy-saving: High heat generation and excellent heat distribution, use less energy than traditional heating methods. Reliable: The indoor temperature can be adjusted freely, free of the limitation of heating season. 2 Health and fresh! Physical therapy: The heat radiant can change body microcirculation, cell organization under skin producing resonance, clearing the barrier of microcirculation, adjusting and balancing nervous system, promoting metabolism, increasing body physical power. It is very good for people's health. Far-infrared radiant heaters are produced by unique design and manufacturing technique. Using a specially coated aluminum panel, the heat generated by the heating element is transferred radiantly to people and objects with maximum efficiency. The heat radiated from the panel surface, is absorbed by people, walls, floors, and furniture et cetera, like sunshine. Infrared heating will not lead to air movement, making the air cleaner, as dust and particles are not disturbed and circulated. Traditional convection heating relies on air movement to distribute the heat. The air remains less humid, and gives you a sense of fresh, comfortable, warmth-similar to the warmth felt from the sun. 5. WORKING CONDITION Ambient temperature: -30 ~ +40 Rated Voltage: 220-240V~ Rated frequency: 50Hz/60Hz Relative humidity: less than 95% 6. INSTALLATION REQUIREMENTS 1. Qualified installer: The installation must be carried out by trained personnel. 2. Installation conditions: (1) Supply voltage fluctuation range should be within ± 10%,If not, please revise before installation. (2) If there is a serious security risk in users' electricity environment, the installation should be refused, until eliminate the security risks. (3) Electricity lines should be equipped with earth leakage protection devices and master switch. (4) Ground wire should be connected to the grounding device on the building, if not, please consult to professional installer, please do not put ground wire to gas pipe, water pipe, lightning rod or telephone grounding wire. Model No. Power(W) JH-NR10-13W 1000 JH-NR18-13W 1800 JH-NR24-13W 2400 JH-NR32-13W 3200 Rated Current(A) 4.3 7.8 10.4 13.9 Voltage(V) 220-240 220-240 220-240 220-240 Cable length(mm) 2000 2000 2000 500 3 7. INSTALLATION INSTRUCTION Health and fresh! Model No. JH-NR10-13W JH-NR18-13W JH-NR24-13W JH-NR32-13W Dimension A 755mm 1155mm 1655mm 2155mm Dimension B 200mm 700mm 1200mm 1700mm Step 1Remove packing of both ends of heater. 4 Step 2Connect adjusting bracket to sliding bracket. Health and fresh! Step 3Installation of sliding bracket & heater, as arrow points. Step 4Fix adjusting bracket into the wall by expansion screws. Step 5Installation of two adjusting brackets; make sure lock brackets tight by butterfly hand screw. 5 8. INSTALLATION DIAGRAM Health and fresh! 6 9. DISPLAY INTERFACE Health and fresh! Manual Key Press Manual Key button to turn on/off the heater, and set the heating level. Long press Manual Key to pair the Wi-Fi network(details as chapter 11). Indoor temperature sensor Using it to collect indoor temperature. 7 10. MANUAL FOR REMOTE CONTROLLER Health and fresh! Remote appearance Remote LED display 1. ON/OFF button Press ON/OFF button to turn on/off heater. 2. Clock button Remote is powered on(as show in picture 2-1), present time is 00:00, time setting as follow: 1)Press clock button, the hour will flash(as show in picture 2-2), press up or down button to change hour setting. 2)Press clock button, the minute will flash(as show in pictures 2-3), press up or down button to change hour setting. 3)Press clock button, the second will flash(as show in picture 2-4), press up or down button to change hour setting. 4)Press clock button again, the second stop flashing and the setting is finished. 8 Health and fresh! Pic2-1 Pic2-2 Pic2-3 Pic2-4 3. Heat button Press level button to adjust the power when the heater is on(as show in picture 3-1). Pic3-1 4. Fast hot button Press fast hot button to turn on/off fast hot function. Fast hot function is to let the heater run at full power for a certain time, to achieve the purpose of rapid heating. Pic4-1 5. Timer on button 1)Press timer on button, it will show ON--:--(as show in picture 5-1). 2)Press up or down to change hour(as show in picture 5-2). 3)Press time on button again, hour stop shining and minute begin to shine, press up or down to change minute(as show in picture 5-3). 4)Press time on button again, timer on function finished. It will show the present time 16;30 and on. Time on setting finished(as show in picture 5-4). 9 Health and fresh! Pic5-1 Pic5-2 Pic5-3 Pic5-4 6.Timer off 1)Press timer off button, it will show off--:--(as show in picture 6-1). 2)Press up or down to change hour(as show in picture 6-2). 3)Press time off button again, hour stop shining and minute begin to shine, press up or down to change minute(as show in picture 6-3). 4)Press time off button again, timer off function finished. It will show the present time 16;30 and off. Timer off setting finished(as show in picture 6-4). Pic6-1 Pic6-2 Pic6-3 Pic6-4 11. CONNECT TO NETWORK 1. Download Tuya Smart App Download Quality Heating Smart App from your smartphone (Google Play Store / App Store / AppGallery, etc.) or by scanning the following code. 10 2. Register / Log in Register an account via mobile number or email address. Log in with existing account if an account has already been set. Health and fresh! 3. Home management 1. Click "Start your smart life" to "Add family" 2. Manually set a family name at "Add family". Set location at the map interface and change the location by coordinate point. 11 Health and fresh! 3. Click "Add Room" to add another room. By click "Done" to finish the room setting. And click "..." to proceed room management as needed. Click "Home Management" to add family. One account can simultaneously control several families by selecting available devices at the family management page. Click a family name to get into the "Family Settings" page and change the name, location and members as needed. 12 Health and fresh! 4. Add Devices Keep pressing Manual Key over 8 seconds after power on, till heater has beep sounds and icon of Wi-Fi flashing (twice per second). Click "add device" or "+" on the screen, find "Small Home Appliance"--"Heater" 13 Health and fresh! Press "Confirm indicator rapidly blink" and select a Wi-Fi signal nearby and enter Wi-Fi password to confirm the connection. Once the device added successfully, press "Done" to finish this procedure. If failed, you need to re-add or search for help. 5. Using App to control heater Once it's connected, you can use the App to control the heater. 14 Switch : Turn on / off heater. Health and fresh! Mode : Set Auto / Manual mode. Auto mode: set temperature. Manual mode: Set temperature at 40(Unchangeable). Level : Change heating levels. Level_1 : Level_2 : Level_3 : Level_4 : Heating at 25% power. Heating at 50% power. Heating at 75% power. Heating at 100% power. Fast Hot : Turn on / off fast heat mode. Timer : Set upmost 30 time logs. WIFI signal strength : Shows the Wi-Fi signal strength. It comes the best at 100. Note: (1) All the above pictures are under iOS system. There's a slight difference between Android system. (2) All the indications are just for your reference. 12. INSPECTION ITEMS AFTER INSTALLATION Items to be checked Situation caused by improperly i Items to be checked installation Is installation stable? Is heat insulation adequate? The equipment may fall off or shake. Damage objects close to equipment. Does power voltage same as voltage shown Equipment failure. on product nameplate? Does wire connection correct? Does electricity ground connected safely? Equipment failure. There is electricity leakage risk. 15 13. ATTENTION Health and fresh! Due to thermal expansion and contraction, the heater would make noise when turning on or off. It's a normal phenomenon, and won't make bad affection. 14. INSPECTION ITEMS FOR COMMISSIONING 1. Do not connect power until installation is complete. 2. All wires connection are correct and firm. 3. All scattered objects must be removed from radiant heater body. 4. Connect power and check heater is operating correctly. 15. PACKING LIST No. Name QTY 1 Heater 1 pc 2 Remote controller 1 pc 3 Adjusting bracket 1 set 4 Fastener 1 set 5 Sliding bracket 1 set 16Microsoft Word voor Microsoft 365