Instruction Manual for CT models including: CF52SIM4BK 48 Inch Integrated LED Indoor Black Ceiling Fan, CF52SIM4BK, 48 Inch Integrated LED Indoor Black Ceiling Fan, Integrated LED Indoor Black Ceiling Fan, LED Indoor Black Ceiling Fan, Indoor Black Ceiling Fan, Ceiling Fan
2 days ago —
22 ore fa — REMEMBER to turn off the power. Follow the steps below to hang your fan properly: 1. Remove the Hitch Pin and Lock Pin from downrod.
Installation & Troubleshooting Manual For Ceiling Fan Email:Aftersales07@hotmail.com Unpack your fan and check the contents. You should have followings: 18 1. M ounting Bracket x1 2. Canopy x1 3. Canopy Cover x1 4. Downrod & Hanger Ball x1 (4 or 8 inch, two sizes,choose accroding to your ceiling height) 5. Hitch Pin x1 6. Lock Pin x1 7. Coupling Cover x1 8. M otor x1 9. Blades x4 10. Lamp Plate x1 11. Lamp Shade x1 12. Remote Receiver X 1 13. Plastic Wire Connectors x3 14. Gaskets x4 15. Wood Screws x4 16. Expansion Screws x2 17. Tapping Screws x12 18. Remote Controller x1 Installation & Troubleshooting Manual For Ceiling Fan Email:Aftersales07@hotmail.com Installation & Troubleshooting Manual For Ceiling Fan Email:Aftersales07@hotmail.com Installation & Troubleshooting Manual For Ceiling Fan Email:Aftersales07@hotmail.com REM EM BER to turn off the power. Follow the steps below to hang your fan properly: 1. Remove the Hitch Pin and Lock Pin from downrod. 2. Place downrod assembly into canop,Canopy Cover and coupling cover,Carefully feed motor wires through the downrod assembly. 3. Loosen the two set screws in downrod coupling 4. Insert downrod into downrod coupling.install coupling through coupling and downrod. Insert Hitch Pin into Lock Pin until it snaps into place. Tighten set screws in coupling. Slide coupling cover over the downrod coupling. 1. Insert each Blades into the designated mounting position at the bottom of the M otor, and securely fasten the Blades to the M otor with Tapping Screws. 2. Repeat the above steps to install the remaining Blades onto the Motor. 3. After installing each Blade, gently shake the Blades to ensure that the connection secure. 1. Secure the Lamp Plate to the triangular piece below the M otor using the three included screws. 2. Ensuring that the Lamp Plate and the triangular piece are firmly locked together. Installation & Troubleshooting Manual For Ceiling Fan Email:Aftersales07@hotmail.com Insert the terminals that come with the M otor the terminal interfaces on the Lamp plate (M ake sure the terminals are correctly inserted into the interfaces,otherwise the light not turns into on). Carefully lift motor assembly and place hanger ball onto hanger bracket. Rotate fan until notch on downrod ball engages the ridge on the mounting bracket, Rod should not rotate if this is donecor rectly. M ake wiring connections from the house and the motor to the remote receiver as shown right. Connect using wire nuts (provided). Installation & Troubleshooting Manual For Ceiling Fan Email:Aftersales07@hotmail.com Once wiring step has been completed, slide the wired remote receiver in between the mounting bracket andthe top of the downrod ball. Raise the canopy up and align the keyholes on the bottom of the canopy with the 2 screws on the bottom of mounting bracket. Rotate the canopy until both screws from the mounting bracket drop into the slot recesses. Tighten screws securely. Place the Lamp Shade into the Lamp Plate and rotate it clockwise until it is securely fastened to the Lamp Plate. Installation & Troubleshooting Manual For Ceiling Fan Email:Aftersales07@hotmail.com Email:Aftersales07@hotmail.com Installation & Troubleshooting Manual For Ceiling Fan Email:Aftersales07@hotmail.comAdobe PDF library 15.00 Adobe Illustrator(R) 24.0