Network Dome Camera Quick Start Guide

Introduction

This guide provides essential information for the quick start and installation of your Network Dome Camera.

Safety Requirements

• Comply with all local electrical safety codes and standards when operating the product.
• Check if the power supply is correct before operating the product.
• Follow the electrical requirements to power the product. Requirements for selecting a power adapter:
  • The power supply must conform to the IEC 60950-1 and IEC 62368-1 standards.
  • The voltage must meet SELV (Safety Extra Low Voltage) requirements and not exceed ES-1 standards.
  • The power supply must meet LPS requirements and not exceed PS2.
• We recommend using the power adapter provided with the product.
• The power supply requirements (such as rated voltage) are subject to the product label.
• Do not connect the product to more than two power supplies unless otherwise specified.

Installation Requirements

• The product must be installed in a location only professionals can access to avoid the risk of non-professionals becoming injured from accessing the area while the product is in operation.
• Professionals must have full knowledge of the safeguards and risks when using the product.

Operation Requirements

• Do not open the cover when the product is powered on.
• Do not touch the heat dissipation component of the product.

Components Included

Review the list below to ensure all the installation components are present and in good condition.

• 1 x Network Dome Camera
• 2 x Product Literature
• 1 x L-Shaped Allen Wrench
• 1 x Mounting Plate
• 1 x Package of Mounting Components
• 1 x Package of Screws
• 1 x MicroSD Card (Not Included)
• 1 x Phillips Head Screwdriver (Not Included)
• 1 x Power Drill (Not Included)
• 1 x Roll of Electrical Tape (Not Included)

Initialization

Follow the instructions to initialize the device prior to use.

1. Read and agree to the Software License Agreement and Privacy Policy.

   (Textual description of agreement prompt)

2. Go to the password setup page by entering the camera's IP address in the browser's address bar.

   (Visual cue: Password Setup Page)

3. Input the desired password and email address. Click the green checkmark ✔️ when done.

   (Textual description of password/email input interface)

Installation Steps

1. Remove the camera's cover and insert the MicroSD card.

   (Diagram: Shows removal of the camera dome cover and insertion of a MicroSD card.)

2. Position the camera using the mounting plate, drill the installation holes, and screw the plate into place. For conduit installations, only do step 3. For in-ceiling installations, proceed immediately to step 4.

   (Diagram: Illustrating camera mounting plate placement, hole drilling, and distinguishing between conduit and in-ceiling installation paths.)

3. For conduit installations, feed the camera cables through the opening on the side of the camera and connect. See optional procedures A and B to create a more secure attachment for these components. Screw the camera to the mounting plate. Reinstall the cover using the L-shaped Allen wrench.

   (Diagram for conduit installation: feeding cables through an opening, connecting them, attaching the camera to the mounting plate, and reinstalling the cover. Mentions optional procedures A and B.)

4. For in-ceiling installations, feed the cables through an opening in the ceiling and connect. See optional procedures A and B to create a more secure attachment for these components. Secure the camera to the mounting plate using the Phillips head screwdriver. Reinstall the cover using the L-shaped Allen wrench.

   (Diagram for in-ceiling installation: feeding cables through a ceiling opening, connecting them, attaching the camera to the mounting plate, and reinstalling the cover. Mentions optional procedures A and B.)

5. Install a protective cover on the cap of the PoE connector before connecting the two wires.

   (Diagram: Shows the installation of a protective cap on the PoE connector.)

6. Wrap the camera's power cable with electrical tape to ensure a secure connection and protect it from water.

   (Diagram: Depicts the wrapping of the camera's power cable with electrical tape.)

7. Position the camera at the desired angle. The camera can be moved up, down, left, right, and rotated.

   (Diagram: Illustrating the adjustment of the camera's viewing angle.)

8. Reinstall the camera's cover. Remove the recyclable film from the camera's dome cover.

   (Diagram: Shows the reattachment of the camera cover and removal of protective film from the dome.)