Spinningfield 3000789 TV Unit

Important Information Before You Start

Please read all instructions carefully before use and retain for future reference.

Maximum Load Capacities:

• Tabletop Maximum: 40kg / 88lb
• Per Shelf Maximum: 5kg / 11lb

Assembly Time: Approximately 30 minutes.

Do not use power tools for assembly.

Do not climb on the unit.

Do not jump on the unit.

Maintenance: Re-tighten fixings every 6 months. Always use the anti-tip straps or wall mounts provided for safe product use (if applicable).

Intended Use and General Safety

Intended Use: This product is not intended for outdoor use, as a climbing structure, or as a toy. Children should be supervised to ensure they do not play with the product.

Assembly Location: Assemble close to the product's intended position. Locate in a suitable area where it will not create an obstruction, and away from sources of combustion.

General Safety: The assembly pack may contain small parts which can pose a choking hazard to children and pets. Place the unit on solid and even ground. Only use in an upright, stable position. Do not overload the product, as this may result in damage or personal injury.

Cleaning & Maintenance: Do not clean with abrasive cloths or chemicals. Solvents or detergents can damage the surface. Periodically check and re-tighten fittings. Re-tighten all fittings after the first week following assembly. To clean, use a sponge with warm water, a soft cloth, and mild detergent. Ensure all parts are present before assembly. If components are missing, contact customer services at support@domu.co.uk. Do not proceed with assembly if any components are missing.

Components and Hardware

This section lists all parts and hardware required for assembly. Please check that you have all items before starting.

Main Components:

• Part 1: Main base/top panel
• Part 2: Side panel
• Part 3: Back panel
• Part 4: Shelf
• Part 5: Shelf
• Part 6: Base panel
• Part 7: Side panel
• Part 8: Back panel

Hardware List:

• A: 13x (6x43mm) - Screws
• B: 13x (15x12mm) - Cam locks/dowels
• C: 12x - Dowels
• D: 8x (M6x25mm) - Screws
• E: 9x (7x38mm) - Screws
• F: 1x - Allen key
• J: 18x (3.5x14mm) - Screws
• K: 2x - Brackets
• L: 2x - Brackets
• M: 4x - Shelf supports
• O: 2x (4x35mm) - Screws
• P: 2x - Wall plugs
• Q: 2x - Wall straps

Assembly Steps

Follow these steps carefully to assemble your unit.

Step 1:

Attach part 1 (main panel) to part 2 (side panel) using 13x of hardware A (screws).

Diagram shows part 1 and part 2 being joined with multiple screws labeled 'A 13x'.

Step 2:

Attach part 4 (shelf) to part 2 (side panel) using 4x of hardware B (cam locks/dowels).

Diagram shows part 4 being attached to part 2 using cam lock mechanisms labeled 'B 4x'.

Step 3:

Attach part 7 (side panel) to part 1 (main panel) using 7x of hardware B (cam locks/dowels) and 4x of hardware C (dowels).

Diagram shows part 7 being attached to part 1 using cam locks and dowels labeled 'B 7x' and 'C 4x'.

Step 4:

Attach part 3 (back panel) to the structure using 2x of hardware B (cam locks/dowels) and 2x of hardware C (dowels).

Diagram shows part 3 being attached to the partially assembled unit using cam locks and dowels labeled 'B 2x' and 'C 2x'.

Step 5:

Attach part 6 (base panel) to the structure using 8x of hardware D (screws).

Diagram shows part 6 being attached to the base of the unit using screws labeled 'D 8x'.

Step 6:

Attach part 8 (back panel) to the structure using 9x of hardware E (screws) and 6x of hardware C (dowels).

Diagram shows part 8 being attached to the rear of the unit using screws labeled 'E 9x' and dowels labeled 'C 6x'.

Step 7:

Insert part 5 (shelf) into the unit, securing it with 4x of hardware M (shelf supports).

Before adding the shelf, feed any wires through the hole at the back.

Diagram shows part 5 (a shelf) being placed into the unit and secured with shelf supports labeled 'M 4x'.

Step 8:

Attach brackets K and L to the back of the unit using hardware J (screws).

Diagram shows brackets labeled 'K' and 'L' being attached to the back panel with screws labeled 'J 16x'.

Step 9:

Final check of all connections. Ensure the unit is stable.

Diagram shows the completed unit with a checkmark symbol, indicating successful assembly.

Wall Mounting Guide

Important: When drilling into walls, always check for hidden wires or pipes. Ensure screws and wall plugs are suitable for supporting the unit. If unsure, contact a qualified tradesperson.

Tips: Use a drill bit that matches the wall plug and hole size. Take extra care when drilling high walls, ceilings, and ceramic tiles; fit wall plugs below ceramic tiles to avoid splitting. Ensure wall plugs are well fitted and secure.

The diagrams show how to attach wall straps (Q) and potentially use wall plugs (P) and screws (J) to secure the unit to the wall for stability.

Diagram illustrates the process of attaching wall straps to the unit and the wall, using screws and wall plugs. Dimensions 'h' are indicated for drilling hole placement.

Customer Information

Disposal: Please recycle where facilities exist. Check with your local authority for recycling advice.

Customer Service: For support or assistance, please contact support@domu.co.uk.

Warranty: Register your product at www.Spinningfield.com/warranty. Retain proof of purchase. Warranty applies to intended use only; misuse invalidates it. Returned goods must be in original packaging with a completed returns form. This does not affect statutory rights.

Copyright: All material in this manual is copyrighted by DOMU Brands. Unauthorized use may violate copyright and trademark laws.

Thank you for purchasing your Spinningfield product.

Spinningfield is a registered trademark of DOMU Brands Ltd. Made in China for DOMU Brands. M24 2RW.