T/T House Bunk Bed with Slide Bridge

Model: WF285894

Brand: Qualfurn

Manufacturer: GIGACLOUD TECHNOLOGY (USA) INC.

⚠ Safety Warnings ⚠

This bed is designed for use only with mattresses meeting the following specifications for the upper and lower bunks: Twin Standard, Length 74"-75", Width 37 ½"-38 ½", Thickness 6" max.
Replacement parts, including additional guardrails, may be obtained from GIGACLOUD TECHNOLOGY (USA) INC. dealers (18961 ARENTH AVENUE CITY OF INDUSTRY, CA, 91748).
Follow all warnings on the upper bunk bed structure and carton. Do not remove warning labels from the bed.
Always use recommended size mattresses or mattress supports to prevent entrapment or falls.
Mattress surface must be at least 5" (127mm) below the upper edge of guardrails.
Do not allow children under 6 years of age to use the upper bunk.
Periodically check that guardrails, ladder, and other components are in proper position, free from damage, and all connectors are tight.
Do not allow horseplay on or under the bed; prohibit jumping on the bed.
Always use the ladder for entering and leaving the upper bunk.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Using a night light may provide added safety for a child using the upper bunk.
Always use guardrails on both long sides of the upper bunk. If the bunk bed is placed next to a wall, the guardrail running the full length should be against the wall to prevent entrapment.
The use of water or sleep flotation mattresses is prohibited.
STRANGULATION HAZARD: Never attach or hang items to any part of the bunk bed not designed for use with it, such as hooks, belts, or jump ropes.
Keep these instructions for future reference.
Prohibit more than one person on the upper bunk.
It is recommended to assemble your bunk bed on the shipping carton to protect your floor or carpet.
Ensure all staples are removed from the box before beginning assembly.

Maintenance

At the beginning: Tighten all hardware. Check metal parts for rust. If found, sand and repaint using a non-lead-based paint meeting the requirements of 16 CFR 1303. Check all wood members for deterioration and splinters. Sand down splinters and replace deteriorating wood members.
Twice a month: Tighten all hardware.
Owners shall be responsible for maintaining the legibility of the warning labels.

Parts List

Part Number	Description	Quantity
1	Top cross bar	1pc
2	Bottom front bar	1pc
3	Top & bottom back bar	3pcs
4	Front side rails	1pc
5	Back side rails	1pc
6	Left guard rails support	1pc
7	Right guard rails support	1pc
8	Top & bottom guard rails support	2pcs
9	Back guard rails support	1pc
10	Front top cross bar	2pcs
11	Back top cross bar	2pcs
12	Middle & bottom bars	6pcs
13	Bottom bars	2pcs
14	Left front leg	1pc
15	Right front leg	1pc
16	Left back leg	1pc
17	Left back leg	1pc
18	Left stair side or left stair side	1pc
19	Right stair side or left stair side	1pc
20	Step stair side	3pcs
21	Slats	14pcs
22	Slide left leg	1pc
23	Slide right leg	1pc
24	Slide panel	1pc
25	Slide support	4pcs
26	Slide bottom panel	1pc

Hardware List

Label	Description	Quantity
A	Ø4x30	31PCS
B	Ø4x15	6PCS
C	6.5x100	18PCS
D	6.5x80	14PCS
E	6.5x60	26PCS
F	1/4x75	8PCS
G	1/4x35	4PCS
H	Ø10x40	58PCS
I	70x26x18	2PCS
J	4x58	1PC

Assembly Steps

Step 1

Assemble two end frames. For each frame, attach two pieces of part 12 (Middle & bottom bars) and one piece of part 13 (Bottom bars) to two legs (parts 16, 17 for one frame; parts 14, 15 for the other). Use hardware C (6.5x100) and H (Ø10x40). The diagram shows the specific connection points for each leg and bar.

Hardware used: 16x C (6.5x100), 20x H (Ø10x40).

Diagram shows two identical side frame assemblies being constructed.

Step 2

Attach the top cross bars. Connect two pieces of part 11 (Back top cross bar) and two pieces of part 10 (Front top cross bar) to the top of the assembled end frames from Step 1. Use hardware C (6.5x100) and H (Ø10x40). The diagram shows how these cross bars connect to the top of the legs.

Hardware used: 2x C (6.5x100), 2x H (Ø10x40).

Diagram shows the two end frames being connected by horizontal bars at the top.

Step 3

Attach the angled roof supports. Connect two pieces of part 3 (Top & bottom back bar) to the top cross bars using hardware E (6.5x60) and H (Ø10x40). The diagram illustrates the placement of these angled pieces to form the house-like roof structure.

Hardware used: 4x E (6.5x60), 4x H (Ø10x40).

Diagram shows two angled roof sections being attached.

Step 4

Assemble the main bunk bed frame and ladder. Connect the side rails (parts 4, 5) and middle/bottom bars (parts 12, 13) to the main structure. Attach the ladder components (parts 18, 19, 20) to the side of the bed. Use hardware D (6.5x80), F (1/4x75), and H (Ø10x40). The diagram shows the lower bunk structure and the ladder assembly.

Hardware used: 10x D (6.5x80), 8x F (1/4x75), 12x H (Ø10x40).

Diagram shows the lower bunk frame being constructed and the ladder parts being attached to one side.

Step 5

Attach the bed slats. Secure 14 pieces of part 21 (Slats) to the frame using hardware A (Ø4x30). Ensure slats are spaced evenly and not screwed too close to the edges to prevent breakage. The diagram shows the placement of the slats and the recommended spacing.

Hardware used: 31x A (Ø4x30).

Note: Do not screw the bed slats to the outermost edge of the bed slats; leave a certain space at the edges, otherwise it will cause the board to break.

Diagram shows slats being screwed into the frame, with close-ups indicating spacing.

Step 6

Assemble the guardrails. Attach guardrail components (parts 18, 19, 20) to the side rails. Use hardware E (6.5x60) and H (Ø10x40). The diagram shows the assembly of the guardrail components for the upper bunk.

Hardware used: 6x E (6.5x60), 6x H (Ø10x40).

Diagram shows guardrail parts being attached to the frame.

Step 7

Attach additional supports. Connect guardrail supports (parts 6, 7, 8, 9) to the frame. The diagram specifically shows parts 6 (x1), 7 (x1), and 8 (x2) being attached. Use hardware D (6.5x80) and H (Ø10x40). These supports reinforce the structure.

Hardware used: 4x D (6.5x80), 4x H (Ø10x40).

Diagram shows additional support pieces being attached to the main frame.

Step 8

Attach the slide. Connect the slide components (parts 22, 23, 24, 25) to the bunk bed frame. Use hardware E (6.5x60) and G (1/4x35). The diagram shows the slide assembly and its attachment points.

Hardware used: 4x E (6.5x60), 4x G (1/4x35).

Diagram shows the slide being attached to the side of the bunk bed.

Step 9

Complete slide assembly and reinforcement. Attach the slide bottom panel (part 26) and further secure the slide structure. Use hardware B (Ø4x15), H (Ø10x40), I (70x26x18), J (4x58), and E (6.5x60). The diagram shows the final connections for the slide and the base.

Hardware used: 4x B (Ø4x15), 10x H (Ø10x40), 2x I (70x26x18), 1x J (4x58), 12x E (6.5x60).

Diagram shows the slide being completed and attached, with various hardware types used.

Step 10

Final check. The bunk bed is now assembled. Ensure all hardware is tightened and the structure is stable. The diagram shows the completed bunk bed with the slide.

Hardware used: 2x B (Ø4x15).

Diagram shows the completed bunk bed.

	Twin Loft Bed with Slide Assembly Instructions Comprehensive assembly instructions for the Twin Loft Bed with Slide, model WF286078. Includes safety warnings, parts list, hardware list, and step-by-step assembly guidance.
	Assembly Instructions for L-Shaped Bunk Bed with Stairs and Drawers Detailed assembly instructions for the L-shaped bunk bed, including safety warnings, part lists, and step-by-step guidance. Features stairs, drawers, and a twin over full configuration. Includes part numbers and hardware specifications for easy assembly.
	Bunk Bed Assembly Instructions - Model MF285535 Comprehensive assembly instructions for the Bunk Bed, model MF285535, including safety warnings, part lists, hardware details, and step-by-step guidance. Features weight limits and mattress size recommendations.
	Qualfurn Twin House Bunk Bed Assembly Instructions - Models WF281277, WF281278 Comprehensive step-by-step assembly guide for the Qualfurn Twin House Bunk Bed. Includes detailed parts list, hardware list, and clear instructions for models WF281277 and WF281278.
	Twin Loft Bed with Slide Assembly Instructions Comprehensive assembly instructions for the Twin Loft Bed with Slide (Model WF286078), including safety warnings, parts list, hardware list, and step-by-step assembly guide.
	Twin House Bunk Bed Assembly Instructions Assembly instructions for the Twin House Bunk Bed, including safety warnings, parts list, hardware list, and step-by-step assembly guide.
	Assembly Instructions: Twin Loft Bed with Shelf (WF291351/WF291352) Comprehensive assembly instructions for the Qualfurn Twin Loft Bed with Shelf (models WF291351 and WF291352). Includes safety warnings, part list, hardware list, and step-by-step guidance for safe and proper assembly.
	QualFurn Bunk Bed with Slide Assembly Instructions Comprehensive assembly instructions for the QualFurn bunk bed with slide and stairway, including safety warnings, part lists, and detailed step-by-step guidance.