CPVAN Independent Smoke Alarm

User Manual and Installation Guide

Product Specifications

Power: DC 3V

Battery Package: CR14505 Lithium Battery, 1600mAh (sealed in)

Operation Current: <10uA (standby); <70mA (alarm)

Alarm Volume: >85 dB(A) at 3 meters

Alarm Sensitivity: 0.09 – 0.17 dB/m

Low Battery: 2.6 ± 0.1 V

Silence Time: approx. 10 minutes

Compliance: Comply to Standard EN14604:2005/AC:2008

Packing List

1 x Photoelectric smoke alarm
1 x Mounting bracket
1 x Screw Kit (install option 1)
1 x 3M Adhesive (install option 2)
1 x User manual

Product Profile

The device is a circular smoke alarm, approximately 120mm in diameter and 31.5mm in height. It features a central speaker grille, a test/silence button, and an LED indicator.

Battery Type: Non-replaceable, sealed lithium battery.

The underside of the alarm shows a sealed battery compartment, indicating a 3V power source.

Installation Instructions

General Placement:

Install an alarm in every bedroom and hallway.
Install an alarm above stairways and on every floor of the house.
Smoke and heat spread horizontally towards the ceiling. Install the alarm in the center of the ceiling.
If the alarm cannot be installed in the center of the ceiling, install it keeping 300mm away from corners. (See Figure 1).
If installed on a wall, maintain a 100mm distance from the ceiling.
For rooms or hallways longer than 30 feet (approx. 9 meters), install multiple alarms.
If the wall or ceiling is sloped, install the alarm at least 500mm from the highest point of the wall or ceiling. (See Figure 2).

Figure 1 Description: A diagram showing ceiling placement. Correct placement is indicated by a green checkmark (✓) for a central ceiling position and a position 100mm from the ceiling on a wall. Incorrect placement is indicated by red crosses (✗) for positions too close to corners (300mm recommended from corners).

Figure 2 Description: A diagram illustrating placement on sloped ceilings, showing incorrect placement (✗) too close to the apex and correct placement (✓) at least 500mm from the highest point.

Figure 3 Description: An exploded view of mounting components: a mounting bracket, two screws, and two plastic wall plugs, with the alarm body shown separately.

Locations to Avoid

High-humidity areas such as kitchens and bathrooms.
Near air outlets, fans, and central heating.
Dusty, dirty areas, or areas with insects.
High-temperature and easily polluted places.
Places with difficult access, making it difficult to operate the test function.
Within 1.5m from lamps.
Next to doors or windows.
In the top of rooms with sloping roofs, corners, or other dead-air spaces.

Mounting Alarms

Twist off the mounting bracket from the alarm.
Place the bracket on the installation position and mark the screw holes on the ceiling or wall.
Drill two mounting holes (5mm diameter) in the marked place and insert two plastic anchor plugs with a hammer.
Screw the mounting bracket to the ceiling or wall (Refer to Figure 3).
Attach the alarm to the mounting bracket and turn clockwise to lock the alarm.

WARNING: Installation instructions must be followed strictly to avoid injury. ⚠️

Powering Up and Powering Off

The device is turned off by default before leaving the factory. To activate:

Power Up: Press the test button for over 10 seconds. The red LED indicator will light up. Release the button; the alarm is powered up and ready to work.

Power Off: Press the test button for over 10 seconds. The red LED indicator will blink twice. Release the button; the alarm is powered off.

Test Your Alarm

Test the unit to ensure proper operation by pressing the cover. The alarm will sound if the unit is working correctly. If no sound is heard, refer to the "Trouble Shooting" section for a solution.

CAUTION:

DO NOT test your alarm using an open flame. This may damage the smoke alarm or ignite combustible materials, potentially causing a fire.
DO NOT stand close to the alarm when it is sounding. Close exposure may be harmful to your hearing; maintain a safe distance during testing.
Perform a weekly test of this smoke alarm.

LED Indicators

Normal Status: GREEN LED flashes once every 60 seconds.
Test Status: Red LED flashes once every second.
Hush/Silence Mode: Red LED flashes once every 8 seconds.
Low Battery Status: Red LED flashes once every 60 seconds and emits 1 beep every 60 seconds.
Fault Status: The alarm will deliver beeps every 40 seconds.

Silence Mode

When the unit is alarming, pressing the test button will pause the alarm for approximately 10 minutes. The red LED will flash once every 8 seconds to indicate silence mode. This feature should only be used for known alarm conditions, such as smoke from cooking. The alarm will automatically reset after approximately 10 minutes. If combustion particles are still present, the alarm will sound again.

CAUTION: Before using silence mode, identify the source of the smoke and ensure a safe condition exists. ⚠️

Maintenance and Cleaning

Follow these simple steps to ensure proper function:

Test the alarm once a week.
Do not paint the alarm. Paint can seal the vents and interfere with the sensor's ability to detect smoke.
Never attempt to disassemble the alarm for internal cleaning, as this will damage the unit.
Clean the alarm at least once a month to remove dust, dirt, or debris. Use a vacuum cleaner with a soft brush to clean all sides and covers.

If a defective battery or other failures occur, refer to the "Trouble Shooting" section. If failures persist during the warranty period, return the unit to your retailer.

Trouble Shooting

Problem	Solution
The alarm does not sound when testing	1. Please check whether the alarm is powered up.
Red LED flashes and the alarm delivers one beep every 60 seconds	1. The battery is low.
The alarm delivers one beep every 40 seconds	1. Clean the alarm. Refer to the "Maintenance and Cleaning" section.
Nuisance alarms triggered intermittently or when residents are cooking, taking showers, etc.	1. Press the silence button. 2. Clean the alarm. Refer to the "Maintenance and Cleaning" section. 3. Move the alarm to a new location.

Warranty Information

CPVAN typically provides a 12-month warranty after installation. For a 24-month extension, please contact CPVAN via email: UK: info@cpvans.com, EU: support2@cpvans.com.

During the warranty period, CPVAN will repair or replace defective Smoke Alarms at its discretion upon return to the retailer. Please include your name, address, phone number, and a brief description of the issue.

Damage caused by neglect, abuse, or failure to adhere to instructions will void the warranty. The unit will not be replaced or repaired.

This warranty does not apply if the alarm has been damaged, modified, abused, or altered after purchase, or if it fails due to improper maintenance.

Certifications and Compliance

This product is CE certified and complies with EN 14604:2005/AC:2008.

It is also TÜV Rheinland certified (ID 0007000000).

The product conforms to EU directives including 2014/30/EU, 2011/305/EU, 2011/65/EU, 2015/863/EU, and 1907/2006/EU.

Symbols include: CE conformity mark, Do not dispose with household waste symbol, Information symbol.

	CPVAN SM11R/HD11R Interlinked Smoke and Heat Detector User Manual User manual for the CPVAN SM11R/HD11R interlinked smoke and heat detector. Includes installation, operation, maintenance, troubleshooting, and warranty details for optimal home fire safety.
	Interlinked Smoke Detector SM11R Quick Reference Guide A quick reference guide for the SM11R Interlinked Smoke Detector, covering product specifications, installation instructions, locations to avoid, mounting, testing, LED indicators, silence mode, interlinked network setup, maintenance, troubleshooting, and warranty information.
	CPVAN CP6 WiFi Home Alarm System Manual & Setup Guide Comprehensive guide to installing, connecting, and using the CPVAN CP6 WiFi Home Alarm System with the Smart Life app and Amazon Alexa. Includes specifications, features, troubleshooting, and setup instructions.
	CPVAN WiFi PIR Motion Sensor Alarm User Manual Comprehensive user manual for the CPVAN WiFi PIR Motion Sensor Alarm, detailing setup, features, and operation for home security.
	CPVAN CP2 PIR Motion Sensor Alarm User Manual This manual provides instructions for the CPVAN CP2 PIR Motion Sensor Alarm, covering setup, operation, pairing, and troubleshooting. Learn how to arm, disarm, change sounds, and add sensors to your home security system.
	CPVan Pet Immune PIR Motion Sensor: Operation Instructions and Features Comprehensive guide to the CPVan Pet Immune PIR Motion Sensor, covering installation, features, mode settings, and technical specifications for CPVan Home Alarm Systems.
	CPVAN Home Alarm System CP9 User Manual and Product Overview Comprehensive guide to the CPVAN Home Alarm System CP9, covering product overview, setup, features, and specifications for base station, remote control, door/window sensors, and PIR motion sensors.
	Remote Control Quick Start Guide A quick start guide for a remote control, detailing its functions, buttons, and technical specifications. Includes FCC compliance information.