Luxury Home & Kitchen Appliances | Fisher & Paykel USA
Luxury Home & Kitchen Appliances | Fisher & Paykel USA
Installation Guide for FISHER PAYKEL models including: VB60SMB1-SET Vacuum Seal Drawer, VB60SMB1-SET, Vacuum Seal Drawer, Seal Drawer, Drawer
Vacuum Seal Drawer, 60cm | Fisher & Paykel United Kingdom
File Info : application/pdf, 15 Pages, 3.41MB
DocumentDocumentVACUUM SEAL DRAWER MINIMAL VB60SMB1-SET & VB60SMG1-SET CONTEMPORARY VB60SDB1-SET INSTALLATION GUIDE NZ AU EU UK IE SG Safety and warnings Vacuum seal drawer models Accessory door panels (purchased separately) Unpack your product Electrical specifications Parts supplied Tools required Product dimensions Cabinetry dimensions Installation options Prior to installation Installing the drawer install front panel (sold separately) Adjusting the height Installer checklist CONTENTS 4 5 5 6 6 7 7 8 9 10 11 12 13 13 14 3 SAFETY AND WARNINGS ! WARNING! Tip Hazard This product may tip. Keep children away and take care. Failure to follow this advice may result in injury. · Drawer must be secured in place by supplied screws. · Ensure there is a fixed shelf directly above the drawer if it is not installed under another product. ! WARNING! Cut Hazard Failure to use caution could result in injury. · Take care: some edges may be sharp. · Do not put fingers in the drawer when closing. ! WARNING! Electric Shock Hazard Failure to follow this advice may result in electrical shock or death. · If the product is damaged, switch the appliance off and disconnect it from the mains to avoid possible electric shock. ! WARNING! Weight Hazard Failure to follow this advice may result in damage or personal injury. · Ensure the bottom shelf of the cabinetry can fully support the weight of combined appliances. 4 SAFETY AND WARNINGS READ AND SAVE THIS GUIDE To reduce the risk of fire, injury to persons or damage when using the appliance, follow the important safety guides listed below. Read all the instructions before using the appliance. Installation z Please make this information available to the person installing the product. z The appliance must be installed by a qualified installer, or Fisher & Paykel trained and supported service technician to avoid faulty electrical connection. z Ensure the installation complies with all clearance requirements and applicable standards and regulations. z When installed in combination with a companion product, the companion product can be placed directly onto the appliance. A built-in shelf at the base of the cabinetry must be able to support the weight of both products. z Ensure the cabinetry is square and level and with correct dimensions. z If installing the appliance directly underneath an oven, ensure you do not damage the oven's lower trim. Fisher & Paykel does not accept any responsibility for any damage resulting from incorrect installation. z Before installing the appliance, inspect for any signs of damage. Do not install or use damaged appliances. z Be careful when stacking the appliances on top of each other to avoid damage to the appliances. Electrical z All connections for electrical power and earthing must be done by a qualified electrician and must comply with local codes and ordinances. z Before installation, ensure that the voltage and frequency listed on the data plate corresponds with the household electrical supply. z When combining with another appliance, ensure each appliance has its own power outlet. Avoid sharing the power point to prevent accidental switching off of the appliance. z Ensure your appliance is properly grounded (earthed). z Connect the drawer to a properly rated, protected and sized power supply circuit to avoid electrical overload. z Do not use an extension cord or a portable electrical outlet device (e.g. multi-outlet outlet box) to connect the drawer to the power supply. Ensure the power supply cord is located so that it will not be stepped on, tripped over or otherwise subject to damage or stress. z Ensure there is a switched outlet in an easily accessible area within 900mm of the centre rear of the product. Servicing z Do not repair or replace any part of the appliance unless specifically recommended in the user guide. All other servicing should be done be a Fisher & Paykel trained and supported service technician or qualified person. z Always disconnect the power supply before doing any installation, maintenance or repair work. z If the power supply cord is damaged, it must be replaced by a qualified electrician or Fisher & Paykel trained and supported service technician. VACUUM SEAL DRAWER MODELS VB60SMB1-SET, VB60SMG1-SET & VB60SDB1-SET ACCESSORY DOOR PANELS (PURCHASED SEPARATELY) ADVB6024SDB ADVB6024SMB ADVB6024SMG 5 UNPACK YOUR PRODUCT Remove the Vacuum Seal Drawer and accessories box from the packaging. Recycle the materials that can be reused. Dispose packaging materials in accordance with local regulations on waste disposal. Inspect the Vacuum Seal Drawer for any signs of damage. Do not install the Vacuum Seal Drawer if it has been damaged. If the product is damaged, contact your local Fisher & Paykel dealer. ELECTRICAL SPECIFICATIONS All electrical work must be done by a qualified electrician, or a Fisher & Paykel trained and supported service technician. Supply 220-240 VAC, 50/60 Hz Service 10 amp circuit Maximum Power 320 W Power outlet* 3-prong grounding-type Power cord (total length) 1800mm * The power outlet must be earthed and located within 35 7/16" (900mm) of the centre rear of the product. RECYCLE RESPONSIBLY 6 PARTS SUPPLIED SERVICE & WARRANTY SERVICE ET GARANTIE SERVIZIO E GARANZIA SERVICE & GARANTIE HUOLTO JA TAKUU SERVICE OG GARANTI Service & Warranty VACUUM SEAL DRAWER MINIMAL VB60SMB1-SET & VB60SMG1-SET CONTEMPORARY VB60SDB1-SET USER GUIDE NZ AU UK IE SG User guide VACUUM SEAL DRAWER MINIMAL VB60SMB1-SET & VB60SMG1-SET CONTEMPORARY VB60SDB1-SET INSTALLATION GUIDE NZ AU EU UK IE SG Installation guide TOOLS REQUIRED 5mm Hex key T20 star-head screwdriver Flat-head screwdriver Pliers 4x20 T20 star head countersunk screw (2) T20 star head screw 4x15 (4) External vacuuming accessories kit Anti-tip bracket (2) Suction inlet adapter (1) Tube (1) Vacuum stopper (1) Stopper adapter (1) 7 E C H I PLAN B A FRONT Actual product dimension may vary by ± 2 mm. 8 PRODUCT DIMENSIONS ISOMETRIC F G D J PROFILE PRODUCT DIMENSIONS A Overall height of drawer B Overall width of drawer C Overall depth of drawer* D Height of chassis E Width of chassis** F Depth of chassis*** G Height of drawer front panel H Depth of drawer front panel and flange I Depth of open drawer J Height from bottom of chassis to bottom of front panel K Depth from front of door to side bracket * Includes front panel and power plug ** Includes side brackets ***Includes power plug VB60SMB1-SET VB60SMG1-SET VB60SDB1-SET MM 140 596 566 140 556 546 136 20 414 2 384 PRODUCT WEIGHT Total weight of drawer* *including packaging VB60SMB1-SET VB60SMG1-SET VB60SDB1-SET KG 38 a PO* CABINETRY DIMENSIONS e c d b PO* f PROFILE PLAN CABINETRY DIMENSIONS VB60SMB1-SET VB60SMG1-SET VB60SDB1-SET MM A Minimum inside height of cavity 142 B Minimum inside width of cavity 560 C Minimum inside depth of cavity 560 D Overall width of cabinetry 600 E Minimum clearance between top of front panel and upper cabinetry panel 3 F Minimum clearance between bottom of front panel and lower cabinetry panel 2 * The power outlet (PO) must be earthed and located within 900mm of the centre rear of the product. Actual product dimension may vary by ± 2 mm. PROUD INSTALL FLUSH INSTALL 9 STANDALONE INSTALLATION Suitable for Minimal and Contemporary 60cm Vacuum seal drawers. A fixed shelf must be installed above the drawer. INSTALLATION OPTIONS COMBINED WITH SINGLE OVEN The 60cm Vacuum seal drawer can fully support a 60cm Fisher & Paykel wall oven. COMBINED WITH COMPANION PRODUCT The 60cm Vacuum seal drawer can fully support a 60cm Fisher & Paykel companion product. Top shelf Top shelf Vacuum Seal Drawer Bottom shelf PROFILE Single oven Vacuum Seal Drawer PROFILE PROFILE Companion product Vacuum Seal Drawer Bottom shelf FRONT 10 FRONT FRONT INSTALL THE AIR FILTER 1 locking cap PRIOR TO INSTALLATION REMOVE THE TRANSIT SCREWS The transport screws must be removed before starting up for the first time to avoid damage to the drawer. power cable holder Unscrew the transport screws from under the power cable and holder. Pull out the locking cap with pliers. transport screws 2 3 4 holder Insert the locking cap in the holder. INSTALL THE ANTI-TIP BRACKETS The anti-tip brackets prevent the drawer from tipping over when opening the drawer. Do not open the drawer if the anti-tip brackets are not installed. air filter Use a slotted screwdriver to screw the air filter into the air filter opening. air filter cover Slide the air filter cover over the air filter opening. Locate the attachment position of the anti-tip brackets in both sides of the cabinetry, Ensure the location of the anti-tip brackets matches the location of the side brackets of the drawer. Refer to 'Product dimensions' for location of side brackets. Secure the anti-tip brackets with screws. 11 INSTALLING THE DRAWER Connect the power plug into the 1 power outlet. Slide the drawer carefully into the 3 cabinetry. Open the drawer and extend fully. 2 * Flush alignment illustrated. 12 Push the drawer back into the cabinetry. Ensure the side brackets engages 4 the anti-tip brackets. Secure the attachment flanges of the drawer to the side edges of cabinetry with 4x20 T20 star head countersunk screws. INSTALL FRONT PANEL (SOLD SEPARATELY) ADJUSTING THE HEIGHT The front panel of the drawer can be adjusted vertically to align with the surrounding cabinetry. Ensure the lower adjustment clip is 1 engaged on the outside of the drawer, between the screw and the drawer. 1 2 Align the tabs on the panel to the chassis and slot into place. Open the drawer fully, and slightly loosen the two screws. 2 3 If required, adjust panel vertically as needed. Adjust to the required height and then re-tighten the screws. The height is adjustable within 5mm. 4 Tighten the screw to secure. 3 Close the drawer and check the alignment. Adjust again if necessary. 13 INSTALLER CHECKLIST IMPORTANT! Read all installation instructions in this manual to see if the unit has been correctly installed. Ensure that installation has been completed correctly before use. Ensure that: F the vacuum seal drawer is level and securely fitted to the cabinetry F any internal packaging has been removed from the drawer F the isolating switch is accessible by the customer F the bottom shelf can fully support the total weight of the combined appliances Test operation: F Open the drawer. F Press the button to turn the vacuum seal drawer on. F Press the button to turn the vacuum seal drawer off and shut the drawer. Complete and keep for safe reference: Model Serial No. Purchase Date Purchaser Dealer Address Installer's Name Installer's Signature Installation Company Installation Date 14 FISHERPAYKEL.COM © Fisher & Paykel Appliances 2023. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. For current details about model and specification availability in your country, please go to our website or contact your local Fisher & Paykel dealer. 592864B 12.23