ATEN - Simply Better Connections | ATEN U.S.A.ATEN - Simply Better Connections | ATEN Corporate HeadquartersProduct Warranty | ATEN Corporate HeadquartersLCD KVM Switches / Consoles | ATEN Corporate Headquarters
User Manual for ATEN models including: CS62US, CS64US, USB KVM Switch, CS64US USB KVM Switch, KVM Switch, Switch
Switch KVM formato cable VGA/Audio USB de 2 puertos (0,9m) - CS62US, ATEN Switches KVM en formato cable | ATEN Belgium - Español
4-Port USB VGA/Audio Cable KVM Switch (0.9m, 1.2m) - CS64US, ATEN Cable KVM Switches | ATEN United Kingdom
File Info : application/pdf, 25 Pages, 1.09MB
DocumentDocumentCS62US / CS64US USB KVM Switch User Manual Compliance Statements FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital service, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Any changes or modifications made to this equipment may void the user's authority to operate this equipment. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. - 2 - FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. KCC Statement RoHS This product is RoHS compliant. - 3 - CUSse6r2MUSan/uCalS64US Online Registration Be sure to register your product at our online support center: International http://eservice.aten.com Online Support International For online technical support including troubleshooting, documentation, and software updates: http:// eservice.aten.com For telephone support, call this number: International China Japan Korea North America 886-2-8692-6959 86-400-810-0-810 81-3-5615-5811 82-2-467-6789 1-888-999-ATEN ext 4988 1-949-428-1111 North America Email Support Online Technical Support Troubleshooting Documentation Software Updates Telephone Support support@aten-usa.com http://www.aten-usa.com/ support 1-888-999-ATEN ext 4988 - 4 - Package Contents Check to make sure that all the components are in working order. If you encounter any problem, please contact your dealer. The CS62US / CS64US USB KVM Switch package contains the following items: 1 2-port CS62US USB KVM Switch or 1 4-port CS64US USB KVM Switch 1 user instructions Note: Read this manual thoroughly and follow the installation and operation procedures carefully to prevent any damage to the unit or any connected devices. The product may be updated, with features and functions added, improved, or removed since the release of this manual. For an up-to-date user manual, visit http://www.aten.com/global/en/ - 5 - Overview The CS62US / CS64US takes a giant step forward from prior cable KVM models in the Petite series, by offering built-in cables, and USB peripheral sharing. A firmware upgrade function that is only supported by the CS64US allows you to keep up with latest available versions. The CS62US / CS64US also offers multiplatform support and computer selection via hotkeys to provide the ultimate in desktop convenience. Furthermore, the CS62US / CS64US features enhanced Video DynaSyncTM technology, which stores the console monitor's EDID (Extended Display Identification Data) to optimize display resolution. Featuring an unbeatable combination of design and functionality, USB peripheral sharing convenience, and enhanced user-friendly operations, the CS62US / CS64US allows users to keep up with the latest innovations in desktop multimedia applications. - 6 - Features One USB console controls two/four USB computers USB mouse port can be used for USB hub and USB peripheral sharing Computer selection via hotkeys Hotkey selection for OS and keyboard language Audio-enabled Multiplatform support Windows, Linux, Mac, and Sun Compact design, built-in all-in-one cables Superior video quality up to 2048 x 1536; DDC2B Video DynaSyncTM Exclusive ATEN technology eliminates boot-up display problems and optimizes resolution when switching between ports Independent switching of the KVM and audio focus Supports multimedia keyboards Supports wireless keyboards and mice Supports multifunction mice Mac/Sun keyboard support and emulation1 Auto Scan function to monitor computer operation HDCP Compliant Non-Powered Firmware upgradable2 Note: 1. PC keyboard combinations emulate Mac/Sun keyboards; Mac/Sun keyboards work only with their own computers. 2. Only CS64US supports firmware upgrade function. - 7 - System Requirements Console A VGA, SVGA, or multisync monitor capable of the highest resolution that you will be using on any computer in the installation A USB keyboard and a USB mouse (Optional) Speakers Computers The following equipment must be installed on each computer that is to be connected to the system: A VGA, SVGA, or multisync video port USB Type-A port Speaker port (optional) Cables The CS62US / CS64US's innovative design features built-in KVM and speaker cables for extra convenience. No further cables are necessary. - 8 - Operating Systems Supported operating systems are shown in the table, below: Windows Linux UNIX Novell Mac DOS OS Version 2000 and higher RedHat 9.0 and higher SuSE 10 and higher Mandriva (Mandrake) 2006, 2007, 2008 Debian 3.1, 4.0 Ubuntu 7.04, 7.10 FreeBSD 5.5, 6.1, 6.2 Sun Solaris 9 and higher Netware 5.0 and higher OS 9 and higher 6.2 and higher - 9 - Components CS62US 2 3 1 4 KVM Cable Connectors 5 6 7 Note: The KVM cable connectors are the same on both models. - 10 - CS64US 2 1 3 4 No. Component 1 port LEDs 2 KVM cables 3 speaker jack 4 console ports 5 speaker connector 6 video connector 7 USB keyboard / mouse connector Description The port LEDs light to indicate that the computer attached to its corresponding port has the KVM focus. These cables attach to the computers in your installation. Your console speakers plug in here. The cables from your console monitor, USB keyboard, and USB mouse plug into these ports. The connectors on the KVM cables plug into the computers in your installation. See Installation Diagram, page 14, for more information. - 11 - Installation 1. Make sure that the power to any device that you connect to the installation has been turned off. You must unplug the power cords of any computers that have the Keyboard Power On function. 2. To prevent damage to your installation from power surges or static electricity. It is important that all connected devices are properly grounded. 3. Please operate the device with caution when under high environmental temperatures, as the surface of the device may become overheated under such conditions. For instance, the surface temperature of the device may reach 70 °C (158 °F) or higher when the environmental temperature reaches close 50 °C (122 °F). Setting up the CS62US / CS64US USB KVM Switch is quick and easy. Refer to the installation diagrams on the following pages (the numbers in the diagrams correspond to the steps, below) and do the following: 1. Plug your USB keyboard, USB mouse, and monitor into their ports on the CS62US / CS64US. These are located on the side of the CS62US and the front of the CS64US. Note: When using a wireless keyboard and mouse combo, the dongle must plug into the CS62US / CS64US's keyboard port in order for the hotkeys to function. 2. Plug your speakers into the speaker jack. 3. Plug the USB, video, and audio connectors of the attached KVM cables into their respective ports on the computers you are installing. 4. Power on the computers. - 12 - Note: The CS62US / CS64US's power on default is to link to the first computer that is powered on. Make sure the computers and devices that the CS62US / CS64US connects to are also properly grounded. - 13 - Installation Diagram 3 2 1 3 - 14 - Port Switching All port switching operations begin by tapping the Scroll Lock key twice. See the following table for full details. Model CS62US Hotkey [Scroll Lock] [Scroll Lock] CS64US [Scroll Lock] [Enter] [Scroll Lock] + [n] [Enter] Action Toggles the KVM and Audio focus between the two ports. Brings the KVM and Audio focus from the port that currently has the KVM focus to the next port on the installation (1 to 2; 2 to 3; 3 to 4; 4 to 1) Note: If the KVM and Audio focus are on different ports, only the KVM focus switches. Brings the KVM and Audio focus to the computer attached to the corresponding Port ID. Note: Replace n with the port number (1, 2, 3, 4). Example 1 (CS62US only) To bring the KVM, USB hub, and audio focus from port 1 to port 2, do the following: 1. Press [Scroll Lock] twice. Example 2 (CS64US only) To bring the KVM, USB hub, and audio focus from port 1 to port 2, do the following: 1. Press [Scroll Lock] twice. 2. Press [Enter]. Example 3 (CS64US only) To bring the KVM and audio focus from a port to a specified port number (e.g., port 2), do the following: 1. Press [Scroll Lock] twice. 2. Press [2]. 3. Press [Enter]. - 15 - Mouse Port Selection Simply double-click the scroll wheel on your USB mouse to switch between ports. The mouse port-switching function allows you to toggle back and forth between the ports. Note: 1. This feature is only supported by CS62US. 2. This feature is only supported by USB 3-key scroll wheel mice. 3. The default setting is OFF. 4. This feature is only supported when mouse emulation is enabled. Model CS62US Hotkey [Num Lock] [-] [W] Action Enables / disables mouse port-switching. - 16 - Invoking Hotkey Setting Mode (HSM) All hotkey operations begin by holding the Num Lock key, pressing and releasing the Minus key, then releasing the Num Lock key. See the following tables for full details. Note: If using [Num Lock] [-] conflicts with other programs, [Ctrl] [F12] can be used instead. See Hotkey Summary Table, page 18, for details. Auto Scanning Model CS62US CS64US Hotkey Action [Num Lock] [-] Starts Auto Scan. The KVM focus cycles [A] from port to port at 5-second intervals. [Scroll Lock] Starts Auto Scan. The KVM focus cycles [Scroll Lock] [A] from port to port at 5-second intervals. [Enter] [Scroll Lock] [Scroll Lock] [A] [n] [Enter] Starts Auto Scan. The KVM focus cycles from port to port at n-second intervals. Note: Replace n with a number between 1 and 99. Note: To exit Auto Scan, press [Esc] or [Spacebar]. Auto Scanning stops when you exit Auto Scan mode. - 17 - Hotkey Summary Table Combination Function [Num Lock] [-] + [H] Toggles between the default [Num Lock] [-] and alternate [Ctrl][F12] HSM invocation keys. [T] Toggles between the default [Scroll Lock] [Scroll Lock] and alternate [Ctrl][Ctrl] port switching keys. [F2] Activates Mac keyboard mapping. [F3] Activates Sun keyboard mapping. [F10] Activates Windows keyboard mapping. [F4] Lists current switch settings via the paste function of a text editor. [F5] Performs a USB keyboard and mouse reset. [F6] [nn] [Enter] Sets the keyboard language layout. Note: nn is a two-digit number that represents one of the following keyboard language codes: US English 33; French 08; Japanese 15. [R] [Enter] Resets hotkeys to the default setting. [M] Enables / disables mouse emulation (CS62US only). [N] Enables / disables keyboard emulation (CS62US only). [W] Enables / disables mouse port-switching (CS62US only). [u] [p] [g] [r] [a] Invokes Firmware Upgrade Mode (CS64US [d] [e] [Enter] only). [Esc] or [Space Bar] Quits hotkey setting mode. - 18 - Keyboard Emulation Mac PC Keyboard Mac Keyboard [Shift] Shift [Ctrl] Ctrl [Ctrl] [1] [Ctrl] [2] [Ctrl] [3] [Ctrl] [4] [Alt] [Print Screen] [Scroll Lock] [Enter] [Backspace] [Insert] [Ctrl] Alt F13 F14 = Return Delete Help F15 Sun PC Keyboard Sun Keyboard [Ctrl] [T] Stop [Ctrl] [F2] Again [Ctrl] [F3] Props [Ctrl] [F4] Undo [Ctrl] [F5] Front [Ctrl] [F6] Copy [Ctrl] [F7] [Ctrl] [F8] [Ctrl] [F9] [Ctrl] [F10] [Ctrl] [1] [Ctrl] [2] [Ctrl] [3] [Ctrl] [4] [Ctrl] [H] Open Paste Find Cut - + Help Compose Note: When using key combinations, press and release the first key [Ctrl], then press and release the activation key. - 19 - The Firmware Upgrade Utility To upgrade the CS64US's firmware, do the following: Note: Only CS64US supports The Firmware Upgrade Utility. 1. From a computer that is not part of your KVM installation, download the latest Firmware Upgrade package for the CS64US from our Internet support site (www.aten.com). 2. Invoke Firmware Upgrade Mode [Num Lock] [-] [Upgrade]. The LEDs flash together to indicate Firmware Upgrade Mode is in effect. Note: While the switch is in Firmware Upgrade Mode, normal keyboard and mouse functions are suspended. You must complete the upgrade or exit Firmware Upgrade Mode to regain normal control of the console. 3. Run the Firmware Upgrade Package file. The Firmware Upgrade Utility Welcome screen appears. 4. Read the License Agreement and enable to I Agree button. 5. Click Next to continue. The Firmware Upgrade Utility main screen appears. All the devices capable of being upgraded by the package are listed in the Devices List panel. 6. Select your device. Its description appears in the Device Description panel. Click Next to perform the upgrade. As the upgrade proceeds, status messages appear in the Status Messages panel, and the progress towards completion is shown in the Progress bar. 7. After the upgrade has completed, a screen appears to inform you that procedure was successful. Click Finish to close the Firmware Upgrade Utility. 8. Set up your KVM installation again. See Installation, page 12. - 20 - Upgrade Failed If the Upgrade Succeeded screen doesn't appear, it means that the upgrade failed to complete successfully, in which case you should return the unit to your local service center for assistance. - 21 - Troubleshooting Symptom Possible Cause Action Mouse and/or Improper mouse Keyboard not and/or keyboard responding. reset. Unplug the cable(s) from the console port(s), then plug it/them back in. KVM switch needs to be reset. Power off all devices on the installation (see safety note, page 9); power off the KVM switch; wait five seconds; then power up USB devices not responding. USB ports need to Unplug the device's USB cable reset. from the USB port on the switch's rear panel, then plug it back in. Device not recognized (Windows). Windows timing problem. Unplug the KVM cable from the computer's USB port; go into Windows' System Settings and remove the Unknown Device entry; plug the KVM cable back in. Windows will now recognize the device. Cannot switch ports by pressing [Scroll Lock] twice Keyboard is incompatible with Scroll Lock invocation. Switch to the Alternate HSM invocation keys using hotkey [T]. Cannot invoke HSM using [Num Lock][-] Incorrect operation for invoking HSM. Hold the [Num Lock] key, press and release the [Minus] key, then release the [Num Lock] key. The [Caps Lock] and [Scroll Lock] LEDS will flash together to indicate that the unit is in HSM. Keyboard is incompatible with [Num Lock] invocation. Switch to the alternate HSM invocation keys by using hotkey [H]. - 22 - Factory Default Settings Setting Port Switching Hotkey Invocation Auto Scan Interval Port Switching Keys Keyboard Operating Platform Default [Scroll Lock] [Scroll Lock] [Number Lock] + [-] 5 seconds ON PC compatible LED Display Status Status Off On Flashing (one) Flashing (all) Indication Port is not selected Port is connected to an active computer Port is connected to an active computer and is being accessed in Auto Scan Mode Firmware Upgrade Mode is invoked - 23 - Specifications Function Computer Connections Console Connections Port Selection Connectors Console Ports Keyboard Video Mouse Speakers KVM Ports Keyboard / Mouse Video Speakers LEDs Cable Length Emulation Video Scan Interval Selected Keyboard / Mouse Power Consumption Environment Operating Temp. Storage Temp. Humidity Physical Properties Housing Weight Dimensions (L x W x H) CS62US CS64US 2 4 1 1 Hotkeys 1 x USB Type A-Female (White) 1 x HDB-15 Female (Blue) 1 x USB Type A-Female (White) 1 x Mini Stereo Jack Female (Green) 2 x USB Type-A Male 4 x USB Type-A Male (White) (White) 2 x HDB-15 Male (Blue) 4 x HDB-15 Male (Blue) 2 x Mini Stereo Jack 4 x Mini Stereo Jack Female (Green) Female (Green) 2 (Green) 4 (Green) 2 x 0.9 m 2 x 0.9 m; 2 x 1.2 m USB 2048 x 1536; DDC2B 5 sec. 199 sec. (default 5 sec.) DC5V:0.33W:14BTU DC5V:0.9W:8BTU 050ºC -2060ºC 080% RH, Non-condensing Plastic 0.28 kg (0.62 lb) 0.58 kg (1.28 lb) 8.75 x 6.08 x 2.80 cm 9.41 x 9.72 x 2.6 cm (3.44 x 2.39 x 1.10 in) (3.7 x 3.83 x 1.02 in) - 24 - Limited Hardware Warranty ATEN warrants its hardware in the country of purchase against flaws in materials and workmanship for a Warranty Period of two [2] years (warranty period may vary in certain regions/ countries) commencing on the date of original purchase. This warranty period includes the LCD panel of ATEN LCD KVM switches. Select products are warranted for an additional year (see A+ Warranty for further details). Cables and accessories are not covered by the Standard Warranty. What is covered by the Limited Hardware Warranty ATEN will provide a repair service, without charge, during the Warranty Period. If a product is detective, ATEN will, at its discretion, have the option to (1) repair said product with new or repaired components, or (2) replace the entire product with an identical product or with a similar product which fulfills the same function as the defective product. Replaced products assume the warranty of the original product for the remaining period or a period of 90 days, whichever is longer. When the products or components are replaced, the replacing articles shall become customer property and the replaced articles shall become the property of ATEN. To learn more about our warranty policies, please visit our website: http://www.aten.com/global/en/legal/policies/warranty-policy/ © Copyright 2022 ATEN® International Co., Ltd. Released: 2022-08-19 ATEN and the ATEN logo are registered trademarks of ATEN International Co., Ltd. All rights reserved. All other brand names and trademarks are the registered property of their respective owners. - 25 -