Product Overview
This document provides installation instructions for the Kendall Howard LINIER® Swing-Out Wall Mount Cabinets. These cabinets are designed for secure wall mounting and offer swing-out functionality for easy access.
Available Cabinet Sizes and Part Numbers:
| Size (U) | Glass Door Part Number | Solid Door Part Number | Vented Door Part Number |
|---|---|---|---|
| 6U | 3130-3-001-06 | 3131-3-001-06 | 3132-3-001-06 |
| 9U | 3130-3-001-09 | 3131-3-000-09 | 3132-3-001-09 |
| 12U | 3130-3-001-12 | 3131-3-001-12 | 3132-3-001-12 |
| 15U | 3130-3-001-15 | 3131-3-001-15 | 3132-3-001-15 |
| 18U | 3130-3-001-18 | 3131-3-001-18 | 3132-3-001-18 |
| 22U | 3130-3-001-22 | 3131-3-001-22 | 3132-3-001-22 |
For Your Safety
⚠️ Read and understand the entire manual before installing.
Support Information
Support is available through the following methods:
- By Phone: 8:00 AM to 5:00 PM CST. 651.213.1333
- By Email: customerservice@kendallhoward.com
- By Mail: 10152 Liberty Lane, Chisago City, MN 55013, United States of America
- By Web: www.kendallhoward.com
Disclaimer
DISCLAIMER: Kendall Howard LLC. endeavors to make this manual accurate and complete. However, Kendall Howard LLC makes no representations or warranties of any kind, expressed or implied, about whether the use of products contained herein would infringe any rights or the correctness, accuracy or reliability of the information contained herein or that said information covers all details, conditions, or variations. The information herein does not provide for every possible contingency in connection with the installation or use of the product(s). The information contained in this document is subject to change without notice or obligation. Kendall Howard LLC assumes no responsibility for the accuracy, completeness or reliability of the information contained in this document. Any reliance placed on the information is therefore strictly at your own risk.
Tools and Hardware Needed
Tools Required:
- Drill
- Phillips Screwdriver
- Flathead Screwdriver
Mounting Hardware:
Mounting hardware is NOT included with the cabinet. You may need mounting screws and anchors.
Diagram Description: Images show a drill, a Phillips screwdriver, and a flathead screwdriver. Also shown are mounting screws and anchors. A note states: "Mounting hardware is NOT included".
Installation Instructions
Step 1: Prepare Mounting Surface
Identify the desired mounting surface. The cabinet's mounting holes are 16 inches apart on center. Mark the mounting surface and install mounting hardware. Leave about 1/4 inch of hardware exposed for mounting.
Diagram Description: A diagram illustrates mounting a cabinet to a wall. It shows screws being inserted into a wall, with a note indicating the keyhole slot on the cabinet should engage with the wall stud. The spacing of mounting holes on the back of the cabinet is shown as 16 inches on center. A close-up shows screws not fully tightened.
Step 2: Mount Cabinet
Place the cabinet on the exposed mounting hardware. Ensure that the hardware fully engages the recess in the cabinet.
Diagram Description: This diagram shows the cabinet being hung on the wall-mounted screws. A close-up view details how the cabinet's mounting slots connect with the wall screws. The back view of the cabinet is also depicted.
Step 3: Secure Cabinet Back
Install additional mounting screws into the back surface of the cabinet. The spacing is also 16 inches on center. Be sure to install mounting screws in the locations nearest to the hinges for proper weight support. Fully tighten hardware.
**IMPORTANT ** Screws going through the hinge are critical! They should be going into the studs to maintain weight capacity.
** HINGES ARE CRITICAL**
Diagram Description: The diagram shows the back of the cabinet with multiple screws being installed. Arrows point to specific screw locations near the hinges, emphasizing their importance for weight support and connection to wall studs.
Step 4: Door Installation & Bushings
There are two pre-installed bushings installed on the non-pivot side of the cabinet door. These bushings are used to protect the door during shipping. These can be removed or saved as spare bushings. The door can also be installed to open to the right or to the left. These bushings are required for proper mounting when changing door opening direction.
Diagram Description: A diagram shows the cabinet door slightly ajar, highlighting the bushings located on the hinge side. Text explains that these bushings protect the door during shipping and can be removed or reused.
Step 5: Adjust Rail Depth
If rail depth needs to be adjusted, unscrew the mounting screw from the top and bottom of the rail. Move the rail to the desired location. Reinstall the rail with the mounting screw and screw plate.
Diagram Description: A diagram illustrates the process of adjusting the depth of a rack rail. It shows a screw being removed from a rail support, the rail being repositioned, and the screw being reinserted.
Step 6: Remove Knockouts
To remove the knockouts, insert a flathead screwdriver into the small opening at the edge of the knockout. Pry the knockout up and twist until the insert becomes free.
Diagram Description: A diagram shows a flathead screwdriver being used to remove a circular knockout from a panel. The screwdriver is inserted into a small notch, and the knockout is pried upwards and twisted.
Warranty Information
General: Kendall Howard offers a Limited Warranty against defects in material and workmanship for its products.
Terms: Products are warranted to be free of defects. Kendall Howard will, at its option, furnish new or factory remanufactured products for repair or replacement.
User: This Warranty extends to the first purchaser for use in the United States and is non-transferable.
Descriptions: The product will conform to descriptions in Kendall Howard's final invoices, orders, proposals, and other descriptive documents. These are not warranties of performance or fitness for a particular purpose.
Warranty Claims Procedure: Within 30 days of discovering a defect, contact Kendall Howard. Repair or replacement of non-conforming products will be provided without charge for materials within 30 days of purchase. Labor charges may apply after 30 days. Kendall Howard covers shipping costs for replacement products and return of defective products. Coverage is subject to inspection confirming a defect.
Items Not Covered: This Warranty does not cover damage or defects caused by misuse, improper application, incorrect electrical current, negligence, inappropriate operating conditions, unauthorized repair, accident, tampering, alterations, relocation, exposure to elements, Acts of God, theft, or installation contrary to recommendations. It also does not cover installation costs, maintenance, or service items. The warranty is void if the serial number is altered or removed, or if the product is altered by the User.
Limitations: This Warranty is in lieu of all other warranties, express or implied, including merchantability and fitness for a particular purpose. The User's sole remedy is repair or replacement. Kendall Howard's liability for property loss or damage shall not exceed the net product purchase price. Indirect, special, incidental, exemplary, or consequential damages are excluded.
Miscellaneous: No salesperson or agent can alter warranty terms. Terms may be modified in writing by a Kendall Howard officer. User must complete and return the User Information Card within 30 days of receipt. This Warranty is governed by the laws of the State of Nebraska.
For details about product warranty, please visit www.kendallhoward.com.
The product features "AMERICAN MADE" components.
Home Page - Kendall Howard
