Installation Guide for beko models including: DDT38532XIHHW Built In Fully Integrated Dishwasher, DDT38532XIHHW, Built In Fully Integrated Dishwasher, In Fully Integrated Dishwasher, Fully Integrated Dishwasher, Integrated Dishwasher
Beko DDT38532XIHHW 24 Inch Stainless Steel Built-In Fully Integrated Dishwasher | Appliances Connection
Beko DDT38532XHW 24 Inch Stainless Steel Built-In Fully Integrated Dishwasher | Appliances Connection
File Info : application/pdf, 29 Pages, 3.46MB
DocumentDocumentDishwasher Installation Manual DDN25401X DDN25402W DDN25402X DDT25401B DDT25401W DDT25401X DDT36430X DDT36430XIH DDT38530BX DDT38530X DDT38530XIH DDT38530X WS DDT38532X DDT38532XIH DDT39432CF DDT39432X DDT39432XIH DDT39434CF DDT39434X DDT39434XIH DIN25401 DIT25401 DIT38530 DIT38532 DIT39432 DIT39434 DUT25401B DUT25401W DUT25401X DUT36420W DUT36420X DUT36520W USA Document Number : 15 9889 0100_BEKO_USA/ 29-11-22.(17:28) DUT36520X DUT36522W DUT36522X DDT38532X WS DIT39434C2 DDT39434XC2 DDT39434XIHC2 DIT38532 WS DDT38532XIH WS DUT25401XHW DUT25401WHW DUT25401BHW DDT38532XHW DDT38532XIHHW To prevent accidents, which could cause serious injury or death, as well as machine damage read these instructions before installation and / or use. INTRODUCTION 1 1. IMPORTANT SAFETY INSTRUCTIONS 1 1.1 INSPECT THE DISHWASHER 2 2. TOOLS WHICH MAY BE NEEDED 3 3. MATERIALS WHICH MAY BE NEEDED 3 4. MATERIALS SUPPLIED 4 4.1 PARTS SUPPLIED 4 4.2 MANUAL BAG 4 4.3 DISHWASHER PARTS BAG 1 4 4.4 DISHWASHER PARTS BAG 2 4 4.5 PARTS ATTACHED TO THE REAR OF THE DISHWASHER 4 5. DISHWASHER SPECIFICATIONS 5 5.1 TECHNICAL FEATURES 6 6. ENCLOSURE PREPARATION 7 6.1 ELECTRICAL PREPARATION 7 6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS 7 6.3 ADJUSTING HEIGHT 10 6.4 INSTALLING THE SIDE TRIM STRIPS 11 6.5 PREPARING THE WATER CONNECTION (A) 11 6.6 DRAIN PREPARATION 12 6.7 STEAM PROTECTION FOIL 14 7. PLACEMENT OF DISHWASHER INTO THE OPENING 15 7.1 DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICAL CONNECTIONS 15 7.2 READJUSTING FOOT LEVELS 18 7.3 ADJUSTING THE MOVABLE TOE KICK 18 7.4 FIXING THE CABINET TO THE COUNTER 20 7.5 PREPARING THE TIMBER DOOR 22 7.6 PREPARING THE PRODUCT DOOR 23 7.9 INSTALLING THE TIMBER DOOR 24 7.10 FIXING THE TIMBER DOOR 24 7.11 FIXING THE TIMBER DOOR 25 7.12 ADJUSTING THE KICK PLATE 25 7.13 CONNECTION 26 8. INSTALLER CHECKLIST 27 9. SELF HELP HINTS: 27 INTRODUCTION Please read this installation manual and particularly the safety instructions completely and carefully. They will save you time and effort and help to ensure optimum dishwasher performance. Be sure to observe all listed warnings and cautions. Look particularly for the icons with exclamation marks inside. The information icon also will provide important references. WARNING CAUTION Ý Notice WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in injury. It may also be used to alert against unsafe practices. NOTICE: Indicates a potentially hazardous situation which, if not avoided, may result in damage to the dishwasher, the table-ware, the equipment or the environment. 1. IMPORTANT SAFETY INSTRUCTIONS In addition to these instructions, the dishwasher shall be installed: · In accordance with all local codes or, in absence of a local code, · In the United States, with the National Electric Code, · In Canada, with the Canadian Electric Code C22.1-latest edition/Provincial and Municipal codes and/or local codes. NOTICE : Read these installation instructions completely before installing and follow them carefully. Save these installation instructions and pass them on to any future user. WARNING When installing the dishwasher, follow basic precautions, including the following: · The dishwasher could only be converted from cord-connected to permanently connected by an authorized service representative. (If needed contact your dealer to schedule an authorized service agent for conversion with an appropriate conversion kit) · Installation and repair should be performed by a qualified installer. Work by unqualified persons could be dangerous and may void the warranty. NOTICE : The dishwasher should be installed by an insured licensed plumber, contractor or trained installer. Installation performed by persons other than this could result in improper installation and property damage. · Do not operate the appliance if damaged, malfunctioning, partially disassembled or if it has missing or broken parts. · Also follow the safety instructions of the user manual. · To reduce the risk of electric shock, fire, or injury to persons, the installer must ensure that the dishwasher is completely enclosed at the time of installation. · Only connect the dishwasher to the power supply when all installation and plumbing work is complete. 1 USA · If the dishwasher is installed in a NOTICE : location that experiences freezing · The dishwasher drain hose must be temperatures (e.g. in a vacation home, installed with a drain loop at least cabin, etc.), you must drain all the 28" (710mm) off the cabinet floor; water from the dishwasher's interior. otherwise the dishwasher may not Water system ruptures that occur as drain properly. a result of freezing are not covered by · This dishwasher is intended for warranty. residential use only, and should not be · Dishwasher must be secured to used in commercial establishments. adjacent cabinetry using the brackets · New installation - If the dishwasher is provided. Failure to do this may cause a new installation, most of the work damage to property or bodily injury. must be done before the dishwasher is · Connect to a properly rated, protected moved into place. and sized power supply circuit to avoid · Replacement - If the dishwasher is electrical overload. The dishwasher replacing another dishwasher, check is designed for an electrical supply the existing dishwasher connections of 120 V (volts), 60 Hz (hertz), AC, for compatibility with the new connected to a dishwasher-dedicated, dishwasher, and replace parts as properly grounded electrical circuit necessary. with a fuse or breakers rated for 15 amperes. Electrical supply conductors 1.1 INSPECT THE DISHWASHER shall be a minimum of # 16 AWG After unpacking the dishwasher and prior copper wire rated at 75 °C (167 °F) or to installation, thoroughly inspect the higher. These requirements must be dishwasher for possible freight or cosmetic met to prevent injury and machine damage. Report any damage immediately. damage. Consult a qualified electrician if in doubt. · Do not use any extension cord or NOTICE : portable outlet device to connect the · Cosmetic defects must be reported dishwasher to a power supply. within 10 days of installation. · Ensure that any plastic wrappings, · Do not discard any bags or items that bags, small pieces etc. are disposed come with the original package until of safely and kept out of the reach of after the entire installation has been children. Danger of suffocation! completed. · Remove the door to the washing compartment when removing an old dishwasher from service or discarding it. Ensure that the appliance presents no danger to children while being stored for disposal. · Old appliances may contain materials that can be recycled. Please contact your local recycling authority about the possibility of recycling these materials. 2 USA 2. TOOLS WHICH MAY BE NEEDED 3. MATERIALS WHICH MAY BE NEEDED (Additional materials may be required to comply with local codes) Hot Water Supply Line - Minimum 3/8" O.D. copper tubing or metal braided dishwasher supply line. Elbow with 3/4" FHT(female threaded) for dishwasher side, and sized to fit your water supply line (copper tubing/compression fitting, or braided hose) on the other side. Dishwasher connection is 3/4" male. UL listed conduit connector or strain relief. Teflon tape or other pipe thread compound to seal plumbing connections. Shut-off valve and fittings appropriate for hot water supply line (copper tubing/compression fitting, or braided hose). Silicone Glue Dishwasher Discharge Hose Adaptor 3 USA 4. MATERIALS SUPPLIED 4.1 PARTS SUPPLIED Parts for your dishwasher will come in several plastic bags. Check your parts bags shown to make sure you have all the parts as listed to the left. 4.2 MANUAL BAG The dishwasher comes with a manual bag containing: · User manual, · Installation manual 4.3 DISHWASHER PARTS BAG 1 This dishwasher bag comes with the following parts: a. Side Trim Strips (Left) b. Side Trim Strips (Right) d. Screws Ø 1/8" x 5/8" (Ø 3.5 mm x 14 mm) e. Mounting Bracket Left f. Mounting Bracket Right g. Spring Clamp h. Screw Clamp j. Rubber Connector k. Toe Kick Bracket - Left l. Toe Kick Bracket Right n. Timber Centering x4 o. Timber Centering Screw x2 p. Toe Kick s. Template t. Hook and loop fastener v. Side centering z. Steam Protection Foil 4.4 DISHWASHER PARTS BAG 2 (MODEL DEPENDING) In addition to the manual bag and the dishwasher parts bag (dishwasher models which can accept a wooden kitchen door) also come with a door panel installation kit which contains: y. Screws 4mm x 36 mm = 3/16th x 1-7/16th yy. Screws Ø 3/16" x 13/4" (Ø 4mm x 43mm) 4.5 PARTS ATTACHED TO THE REAR OF THE DISHWASHER a. Side Trim Strips (Left) b. Side Trim Strips (Right) 4 USA 5. DISHWASHER SPECIFICATIONS TALL TUB MODELS 27 / " -29 / " (700 mm - 760 mm) (52510mm" ) 23 (598 /" mm) Min. Max. 169.6.8lblbss((39kkgg)) 23 (592 / mm -"6-0233mm/) " /(18"mMmin) . 33 " - 35 " (861 mm - 911 mm) 34" - 35 " (864 mm - 913 mm) (61204m" m) (60203mm -"6-1204m"m) 19 11/16" max 500mm STANDARD TUB MODELS 26" -28 / " (660 mm - 720 mm) (52510mm" ) 23 (598 /" mm) Min. Max. 169.6.8lblbss((39kkgg)) 32 / " -36 / " (818 mm - 918 mm) 32 / " - 36 / " (820 mm - 920 mm) (61204m" m) (60203mm -"6-1204m"m) 23 (592 / mm -"6-0233mm/) " /(18"mMmin) . 5 USA 5.1 TECHNICAL FEATURES Permissible water pressure Electrical connection Total power Heater power 4.35 - 145 psi (0.3 - 10 bars) 120 V (volts), 12 A (amps), 60Hz (hertz) 1400 W (watts) 1100 W (watts) NOTICE : Because we continually strive to improve our products, we may change our specifications and design without prior notice. This device corresponds to the following directives: UL 749 Household Dishwasher directive. 6 USA 6. ENCLOSURE PREPARATION 6.1 ELECTRICAL PREPARATION WARNING The dishwasher is designed for an electrical supply of 120 V, 60 Hz, AC, connected to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breaker rated for 15 amperes. 6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS e-f) STANDARD TUB MODELS 7 USA d) ? 8 USA (Depends on model) max 5 0 + 50 j (+50mm) WARNING Dishwasher must be secured to adjacent cabinetry using the mounting brackets provided. Failure to do this may cause damage to property or bodily injury. TALL TUB MODELS ONLY Tighten the plugs on both sides of your machine (v) 9 USA Place the two mounting brackets into the top corners of the dishwasher. Fix the mounting brackets (A) to the top corners of the dishwasher, with the screws supplied. Bend sides of mounting brackets (B) in order to fix from sides (if necessary). 6.3 ADJUSTING HEIGHT If the height of the enclosure is 337/8" to 357/8" (861 mm - 911mm) adjust supports as shown in the figure. Supplied (4) Adjust the front foot level with the adjusting wrench to balance and raise the dishwasher to the enclosure height. Adjust the rear foot level with a screwdriver to balance and raise the dishwasher to the enclosure height. A NOTICE : · Make sure the dishwasher is plumb and notice dishwasher can be placed with a small clearance under the counter top. · Turning the screwdriver in the direction of the black arrows will bring the dishwasher back feet up. · Turning the screwdriver in the direction of the white arrows will take the dishwasher rear feet down. B 10 USA 6.4 INSTALLING THE SIDE TRIM STRIPS Remove the adhesive tape (Figure A). Place the trim strips on the front edge of the side walls (Figure B). NOTICE : · Make sure you use the correct trim strip since there is a left and right side strip. The flexible material should be facing forward (Figure B). 6.5 PREPARING THE WATER CONNECTION (A) Install an easily accessible shut-off valve (not supplied) in the water supply line. All solder connections must be made before the water line is connected to the dishwasher's water inlet valve. Water can also be supplied to the dishwasher by using a flexible braided hose line. Check with your plumbing supply sources for the proper hose and elbow and necessary fittings for the water supply line. This material is not supplied, and must be purchased separately. Water Connection 11 USA WARNING Installation should be performed by a qualified installer. Work by unqualified persons could be dangerous and may void the warranty. If the dishwasher is installed in a location that experiences freezing temperatures (e.g. in a vacation home, cabin etc.), you must drain all the water from the dishwasher's interior. Water system ruptures that occur as a result of freezing are not covered by warranty. 6.6 DRAIN PREPARATION The dishwasher drain hose may be connected to the drain plumbing in one of three ways (Figure A, B, C). NOTICE : · Either one of the above methods must be used or the dishwasher will not operate properly. · A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher. If your sink has one, it is recommended that the hose be disconnected and the hole plugged. · The total length of the drain hose is 763/4" (1950mm). If a A hose extension is required, a drainage hose of equal quality must be used. · The maximum length must not exceed 157 ½" (4000mm). Otherwise, the cleaning process is negatively influenced. 6.6.1 UNDER THE SINK DRAIN Install a Y-branch tail pipe. (Figure A) NOTICE : You must add a loop at least 28" (710mm) above the floor of the cabinet and above the drain connection in the drain hose to B prevent waste water from not draining properly, and causing either poor washing results or a bad odor. 6.6.2 INSTALLING AN AIR GAP If the local ordinance requires an air gap (Figure B). NOTICE : Check with local ordinance for type of air gap required. 6.6.3 DISPOSAL Remove the drain connection plug before attaching the drain hose from the dishwasher. C Every disposal has a hook up for a dishwasher; consult your disposer manual for correct connection. (Figure C) 12 USA 6.6.1 UNDER THE SINK DRAIN (ALTERNATIVE) · · · A · Due to the local buldng code requrements, some dshwasher nstallatons requre hookng up dscharge hose to an ar gap located next to the snk n ktchens. Snce the connecton dameter s dfferent than standard dscharge hose connectons, please use the connector pece provded wth the machne wth nstructons llustrated. · · · · 13 USA 6.7 STEAM PROTECTION FOIL Steam will form inside the dishwasher during operation. At the end of the cycle, when the dishwasher door is opened, it is required to use a steam protection foil to prevent any steam from collecting on the underside of the counter top. 6.6.2 FITTING THE PROTECTION FOIL Before applying the steam protection foil to the underside of the countertop, clean the area with a damp cloth (as shown in Figure A). Once the area dries, apply the steam protection foil. A The steam protection foil will be applied at the location where the hot steam escapes when you first open the door (as shown in Figure B). B CAUTION Steam protection foil must be applied where the steam escapes when door is first opened. Failure to install the steam protection foil during installation can lead to damage to the cabinets and countertop. 14 USA 7. PLACEMENT OF DISHWASHER INTO THE OPENING Now place the dishwasher into the opening and get ready to connect all hoses and electrical connections. CAUTION Make sure all hoses are pulled through the side opening of the cabinet, no hoses are kinked and all slack is taken out as shown in the above figure. 7.1 DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICAL CONNECTIONS 7.1.1 DRAIN HOSE CONNECTION Connect the drain hose to the drain plumbing. 1. Use the supplied rubber connection hose and drain hose clamps to connect the dishwasher drain hose to the plumbing drain connection. 2. Use the spring clamp to secure the rubber connection hose to the dishwasher drain hose. Use the screw clamp to secure the rubber connection hose to the plumbing drain connection. Note that the marks on the rubber connection hose should be on the drain hose side 15 USA 7.1.2 WATER SUPPLY CONNECTION Water supply may be connected to the dishwasher in one of two ways: · With metal braided hose. · With copper tubing. CAUTION · Hot water supply line: Use minimum 3/8" O.D. copper tubing or metal braided dishwasher supply line. · Temperatures required for soldering and sweating will damage the dishwasher's water inlet valve so if any such operation is needed, keep the heat source min. 77/8" (200mm) away from the dishwasher's water inlet valve. · There should not be any sharp bends in the water line that may restrict the water flow. · Teflon tape or pipe tread compound must be used for sealing the connection. Before connecting the copper water supply line to the dishwasher, flush it with hot water to clear any foreign material. NOTICE : After connections are made turn on the water supply to check for leaks. 7.1.3 ELECTRICAL CONNECTION WARNING · Make sure the voltage and frequency listed on the data plate correspond with the household electrical supply. This data must correspond to prevent injury and machine damage. Consult a qualified electrician if in doubt. · Only connect the dishwasher to the mains when all installation and plumbing work is complete. · Do not use any extension cord or portable outlet device to connect the dishwasher to a power supply. · The power-supply receptacle for the appliance shall be installed in a cabinet or on a wall adjacent to the undercounter space in which the appliance is to be installed. · The access hole of the supply cord to the installation compartment must be smooth and rounded and it must be large enough for the attachment plug to pass through. The longest dimension of the opening shall not be more than 1,5" (38 mm).If the partition is metal, it needs to be covered with an edge protector. · Care must be taken when the appliance is installed or removed, to reduce the likelihood of damage to the power-supply cord. 7.1.4 GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances. This appliance must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. 16 USA WARNING Improper connection of the equipmentgrounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded. Do not modify the plug provided with the appliance, if it will not fit the outlet, have a proper outlet installed by a qualified electrician. 17 USA 7.2 READJUSTING FOOT LEVELS Now that the dishwasher is in the cabinet you must readjust the feet to bring the dishwasher up to the required height and attach it underneath the countertop. 1. Readjust the front foot levels with adjusting wrench to balance the dishwasher and raise it up under the countertop, make sure the unit is level. 2. Readjust the rear foot levels with a screwdriver to balance the dishwasher and raise it to the required height using the brackets supplied. 3. Attach the dishwasher underneath the countertop with the four screws supplied (Ø 1/8" x 1/8" - Ø 3.5mm x 14mm). Make sure you do not go through the top of the countertop or damage granite. 7.3 ADJUSTING THE MOVABLE TOE KICK Now that you have successfully installed the dishwasher, you need to attach the toe kick to the dishwasher. The two piece toe kick can be adjusted to the height and depth needed for your kitchen. Be sure to use the slotted toe kick in the front and the other behind it. They slide into each other. Place parts K and L to the channel shown in Figure A for both sides as shown in Figure B. Then fix them in the direction shown with the arrow in Figure C and Figure B. TALL TUB MODELS ONLY 18 USA TALL TUB MODELS ONLY Open the fixing part on the Toe Kick(p). (A) Place it on the slots, which are on the brackets fixed before, and adjust the height (max. 40 mm). (B) Close the fixing part on the Toe Kick. (C) 19 USA 7.4 FIXING THE CABINET TO THE COUNTER STANDARD TUB MODELS (y) 20 USA TALL TUB MODELS y 21 USA 7.5 PREPARING THE TIMBER DOOR X X =? o) s) = = = = Mid. Point n) Weight (max) 9 Kg / 19 lbs t) Mid. Point Height (h) Height (h) Width (w) Thickness (t) Weight (max) : Height of the wooden door 30" (760mm) Tall Tub Models Only : Height of the wooden door 28" (720mm) Standard Tub Models Only : 23 ¼" to 23 ½" (592mm - 595mm) : ¾ " (19mm) : 9 Kg / 19 lbs 22 USA 7.6 PREPARING THE PRODUCT DOOR 1 (t) 2 23 USA 7.9 INSTALLING THE TIMBER DOOR 4 1 3 2 7.10 FIXING THE TIMBER DOOR 12345 6 1234 5 6 24 USA 7.11 FIXING THE TIMBER DOOR (yy) Ø 4 x 43mm 12 3 4 5 1 2345 7.12 ADJUSTING THE KICK PLATE · Check whether the bottom of the door hits the toe kick of the kitchen cabinet (A). · If the door hits the toe kick cut the necessary section out of the toe kick (B). · Apply silicon or sealant to the cut edge of the kitchen cabinet toe kick or paint so it does not absorb moisture. 25 USA 26 USA 2 1 1 2 4 3 2 c 1 max 1000 max 1000 min 500 min 300 min 120 3 ~ 1500 ~ 1800 ~ 2000 4 min 300 min 500 max 1000 2 1 7.13 CONNECTION 8. INSTALLER CHECKLIST Your installer must have completed and checked the following: · The dishwasher is square and level. · The dishwasher is fastened securely to the cabinetry. · The dishwasher door opens and closes freely. The dishwasher door must close without hitting any cabinetry or counter top. · The inlet water supply is turned on and checked for leaks. · The drain hose has been connected and checked for leaks. There must be no kinks or obstructions in the drain hose. · The drain hose must be installed with a 28" (710mm) high drain loop for drain hook-ups without any air removed. · If the dishwasher drain is hooked up to a garbage disposal, the drain hopper plug must be removed. · The spray arms are free and rotate freely. · The rinse cycle has been run. · The water level will be below the filter screen after the end of the wash program. It is normal to find some water in the drain filter area. · Remove drain hose from disposal making sure plug is removed. NOTICE : · If your dishwasher is not operating properly after following these steps: Contact your dealer to schedule an authorized service agent to inspect your new dishwasher for any function related failure. · The manufacturer warranty does not cover installation, conversion or customer education service visits. You will find the model and serial number information on the label located on the right-hand side of the inner door of your dishwasher, as shown above. NOTICE : Please make a copy of your invoice and keep it with this manual and register your dishwasher on-line. 9. SELF HELP HINTS: The screen does not come on: · Check to make sure the breaker to the dishwasher is in the on position. · Check to make sure that the Supply cord is plugged. No Water is coming into the dishwasher: · Check to make sure the hot water shut-off is in the ON position. Water does not drain: · Make sure drain hose is not kinked or comes out of air gap next to the sink. 27 USAAdobe PDF Library 17.0 Adobe InDesign 18.0 (Windows)