LiftMaster MyQ® CONTROL PANEL

Application

The MyQ Control Panel is intended to be installed with Security+® Garage Door Openers manufactured between 1998 and present. The MyQ Control Panel is NOT compatible with Security+ 2.0® Garage Door Openers. DO NOT install this door control on garage door opener systems controlling one-piece or swing doors.

Overview

The MyQ Control Panel offers a quick and convenient way to add Security+ 2.0 and MyQ technology to your existing garage door opener. MyQ technology uses a 900MHz signal to provide two-way communication between the garage door opener and MyQ enabled accessories. When programmed to the LiftMaster® Internet Gateway, you can monitor and control your garage door from any internet-enabled computer or smartphone. You may program up to 12 Security+ 2.0 remote controls, 2 Security+ 2.0 keyless entries, and a combination of 16 MyQ accessories to the MyQ control panel.

Compatible Accessories

Safety Warnings

⚠️ To prevent possible SERIOUS INJURY or DEATH from electrocution:

• Be sure power is NOT connected BEFORE installing door control.
• Connect ONLY to 7-28 VOLT low voltage wires.

⚠️ To prevent possible SERIOUS INJURY or DEATH from a closing garage door:

• Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet (1.5m) above floors, landings, steps or any other adjacent walking surface, and away from ALL moving parts of door.
• NEVER permit children to operate or play with door control push buttons or remote control transmitters.
• Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
• ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door.
• DO NOT install this door control on garage door opener systems controlling one-piece or swing doors.

To provide an adequate visual alert, the garage door opener light bulb(s) MUST be a minimum of 40 Watt (or equivalent).

⚠️ WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Installation

1. Disconnect all electrical and battery power (if applicable) to the garage door opener.
2. Remove the existing door control from the wall.
3. Note the polarity of the wires connected to the existing door control:
   • Label the wire connected to the RED terminal.
   • Label the wire connected to the WHITE terminal.
   Disconnect the wires from the existing door control.
4. Connect the wires to the new MyQ Control Panel. Make sure the polarity is correct:
   • Red wire to the R terminal.
   • White wire to the W terminal.
5. Mount the MyQ Control Panel to the wall.
6. Reconnect power. The yellow command LED and the red learn LED will blink quickly for up to 5 minutes as the control panel recharges. When the control panel is operational, the yellow command LED will glow steadily.
7. To test the control panel, press the [Push Bar] to activate the garage door opener.

Diagram Description: Shows the wiring connection. The existing door control has RED and WHITE wires. The MyQ Control Panel has R and W terminals. The RED wire from the existing control connects to the R terminal on the MyQ panel, and the WHITE wire connects to the W terminal.

Programming

Remote Control

1. Press the MyQ Control Panel [LEARN button] twice; the [Red Learn LED] will turn on.
2. Press the button on the remote control that you wish to operate your garage door.
3. The garage door opener lights will flash (or two clicks will be heard) when the code has been programmed.

Keyless Entry

1. Press the MyQ Control Panel [LEARN button] twice; the [Red Learn LED] will turn on.
2. Enter a 4-digit [PIN] of your choice on the keyless entry keypad. Then press the [ENTER button].
3. The garage door opener lights will flash (or two clicks will be heard) when the code has been programmed.

MyQ Enabled Accessories

1. Press the MyQ Control Panel [LEARN button] twice; the [Red Learn LED] will turn on.
2. Press the [LEARN button] on the MyQ device.*

*MyQ accessories may be programmed to the LiftMaster® Internet Gateway (Model 828LM) or the MyQ control panel. For instructions on programming to the internet gateway refer to the manual.

LiftMaster® Internet Gateway (Not Provided)

The LiftMaster Internet Gateway gives you control of your garage door from your internet-connected computer or mobile device.

To program your MyQ Control Panel to the LiftMaster Internet Gateway:

1. Download the MyQ App.
2. Set up an account and connect.
3. Select "Internet Gateway" and follow the instructions in the app.

IMPORTANT: When instructed to press the “Learn” Button, this will be located on the MyQ Control Panel and the “Learn” button must be pressed 2 times.

For more information on connecting your garage door opener, visit LiftMaster.com/Customer-Support.

Diagram Description: Shows the MyQ Control Panel with labeled components: [LEARN button], [Yellow Command LED], [Red Learn LED]. Also shows a keypad with numbers, [ENTER button], and [PIN] input area for Keyless Entry programming. Another diagram shows a MyQ device (e.g., Model 823LM) with a [LEARN button].

Functions

Push Bar

Press the [Push Bar] to open or close the door.

Lights

Press the [LIGHT button] to turn the garage door opener lights on or off. When the lights are turned on they will stay on until the [LIGHT button] is pressed again, or until the garage door opener is activated. Once the garage door opener is activated, the lights will turn off after the specified period of time (the factory setting is 4-1/2 minutes). The [LIGHT button] will not control the lights when the door is in motion.

To change the amount of time the garage door opener lights will stay on:

Press and hold the [LOCK button] until the garage door opener lights flash.* The time interval is indicated by the number of flashes.

* To cycle through the time intervals repeat the step above. (Approximately 10 seconds)

Light Feature (Default is Active): The lights will turn on when someone enters through the open garage door and the safety reversing sensor infrared beam is broken.

Deactivate: Press and hold the [LIGHT button] until the garage door opener lights turn on, then off again.*

Activate: Start with the garage door opener lights on. Press and hold the [LIGHT button] until the garage door opener lights turn off, then on again.*

Motion Sensor

This feature will automatically turn on the garage door opener lights when motion is sensed. The lights will come on for the set period of time, then shut off.

Activate/Deactivate: Slide the [Motion Sensor Switch] ON or OFF.

Timer-to-Close (TTC)

NOTE: DO NOT install this door control on garage door opener systems controlling one-piece or swing doors.

The TTC feature automatically closes the door after a specified time period (1, 5, or 10 minutes). Once the TTC has been set and the door is open, the [TTC LED] for the selected close interval will blink and begin to count down to close the door. The control panel will beep and the garage door opener lights will flash before closing the door.

The TTC feature will deactivate if the garage door encounters an obstruction twice; or the safety reversing sensors are incorrectly installed. The garage door will reverse open and WILL NOT close until the obstructions are clear or the safety reversing sensors are correctly installed. When the obstruction has been cleared or the safety reversing sensors have been aligned, the door will close when the garage door opener is activated.

Activate: Press and hold the [ON button] until one of the [TTC LEDs] light up. Then press the [ON button] again to cycle through the time interval options (the corresponding TTC LED will light for each time interval). The garage door opener light bulbs will blink as confirmation.

Deactivate: Press and hold the [OFF button] until all [TTC LEDs] turn off and a beep is heard from the control panel.

Temporarily hold door open (suspend TTC): Press and release the [HOLD OPEN button]. The [HOLD OPEN button] will begin to flash. Press the [HOLD OPEN button] again to resume normal TTC operation.

LOCK

Your remote controls will NOT work when LOCK mode is active, however your keyless entry will still allow access to your garage.

Activate*: Press and hold the [LOCK button] for 2 seconds. The [Command LED] will flash as long as the lock feature is activated and your handheld remote control will not operate your door at this time.

Deactivate: Press and hold the [LOCK button] again for 2 seconds. The [Command LED] will stop flashing and normal operation will resume.

* Your LiftMaster® keypad will continue to work when the LOCK has been activated.

Diagram Description: Shows the MyQ Control Panel with labeled components: [Push Bar], [LEARN button], [LOCK button], [ON button], [OFF button], [HOLD OPEN button], [LIGHT button], [Motion Sensor Switch], [Red Learn LED], [Yellow Command LED], and [TTC LEDs] (1 minute, 5 minutes, 10 minutes).

Troubleshooting

• If the [Yellow Command LED] does not turn on, reverse the wires connected to the [R terminal] and [W terminal] of the control panel. Replace wire if necessary.
• If the [Yellow and Red LEDs] are blinking slowly, the control panel is not compatible with your garage door opener.
• If the [Yellow and Red LEDs] are blinking quickly, the control panel is charging, and may take up to 5 minutes to become operational.

Warranty

Five Year Limited Warranty

LiftMaster warrants to the first consumer purchaser of this product that it is free from defect in materials and/or workmanship for a period of 5 years from the date of purchase.

For Service Dial Our Toll Free Number

1-800-528-9131

LiftMaster.com

FCC/IC Compliance

NOTICE: This device complies with Part 15 of the FCC rules and Industry Canada's license-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device must be installed to ensure a minimum 20 cm (8 in.) distance is maintained between users/bystanders and device.

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules and Industry Canada ICES standard. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.