User Manual for APPA models including: 61, 62, 62T, 61 Digital Multimeter, Digital Multimeter, Multimeter
61/62/62T EN Disable Auto Power Off Non-Contact Voltage (Volt sense) 1. Volt sense switch will be activated on any function or at OFF status. 2. Test leads are not used for the Volt sense test.
File Info : application/pdf, 62 Pages, 4.10MB
DocumentDocument61/62/62T
User Manual / /
EN Top of Low-Cost Digital Multimeters TC SC JP RU
YEAR S LIMITE D WARRAN TY
61/62/62T
EN
Read First
Safety Information
Understand and follow operating instructions carefully.Use the meter only as specified in this manual; otherwise,the protection provided by the meter may be impaired.
WARNING
· When using test leads or probes, keep your fingers behind the finger guards. · Remove test lead from Meter before opening the battery door or Meter case. · Use the Meter only as specified in this manual or the protection by the Meter might be impaired. · Always use proper terminals, switch position, and range for measurements. · Never attempt a voltage measurement with the test lead inserted into the A input terminal. · Verify the Meter's operation by measuring a known voltage. If in doubt, have the Meter serviced. · Do not apply more than the rated voltage, as marked on Meter, between terminals or between any terminal and earth ground. · Do not attempt a current measurement when the open voltage is above the fuse protection rating. Suspected open circuit voltage can be checked with voltage function. · Only replace the blown fuse with the proper rating as specified in this manual. · Use caution with voltages above 30 Vac rms, 42 Vac peak, or 60 Vdc. These voltages pose a shock hazard. · To avoid false readings that can lead to electric shock and injury, replace battery as soon as low battery indicator <appears. · Disconnect circuit power and discharge all highvoltage capacitors before testing resistance, continuity, diodes, or capacitance. · Do not use Meter around explosive gas or vapor. · To reduce the risk of fire or electric shock do not expose this product to rain or moisture.
61/62/62T
EN
Caution
· Disconnect the test leads from the test points before
changing the position of the function rotary switch.
· Never connect a source of voltage with the function rotary
switch in / /
A / /Hz position.
· Do not expose Meter to extremes in temperature or high
humidity.
· Never set the meter in
A function to measure the
voltage of a power supply circuit in equipment that could
result in damage the meter and the equipment under test.
Symbols as marked on the meter and Instruction card
Risk of electric shock
See instruction card
DC measurement
Equipment protected by double or reinforced insulation
Battery
Fuse
Earth
AC measurement
Conforms to EU directives
Do not discard this product or throw away
Maintenance Do not attempt to repair this Meter. It contains no userserviceable parts. Repair or servicing should only be performed by qualified personnel.
Cleaning
Periodically wipe the case with a dry cloth and detergent. Do not use abrasives or solvents.
61/62/62T
EN
Measuring AC/DC Voltage And Frequency
Testing for Continuity and Diode
61/62/62T
EN
Resistance and Capacitance (Capacitance for 62, 62T only)
Note To improve the measurement accuracy of small value capacitor, record the reading with the test leads open then substract the residual capacitance of the Meter and leads from measurement. CUNKNOWN = CMEASUREMENT - CRESIDUAL
MIN MAX Record (For 62, 62T only)
61/62/62T
EN
Measuring DC / AC Current (For 62, 62T only)
Temperature °C ,°F
61/62/62T
EN
Manual Ranging and Auto Ranging Auto Power Off (Battery Saver)
61/62/62T
EN
Disable Auto Power Off
Non-Contact Voltage (Volt sense)
1. Volt sense switch will be activated on any function or at
OFF status. 2. Test leads are not used for the Volt sense test. 3. Press the Volt sense button. The display goes black, a
tone sounds and the red LED lights up toverify the instrument is operational. The Volt sense button must be held down to detect the presence of voltage without use
of the leads. 4. If a voltage of 50V to 600V (50 to 500Hz) is detected
near the top of meter a continuous tone sounds and the red LED near the top of meter Illuminates.
61/62/62T
EN
Fuse Replacement (For 62, 62T only) Refer to the following figure to replace fuse :
Caution · Use only a fuse with the amperage, interrupt, voltage, and speed rating specified. · Fuse rating : 10A, 500V Battery Replacement Refer to the following figure to replace the batteries :
Caution · Replace the batteries as soon as the low batteries
indicator " " appears, to avoid false reading. · Batteries 1.5V x 2
61/62/62T
EN
Electrical Specifications
Accuracy is ±(% reading + number of digits) at 23°C ± 5°C < 80%RH.
DC / AC Volts
Range 200.0mV * 2.000V * 20.00V ~ 200.0V * 750V AC / 1000V DC
AC Accuracy Unspecified ±(1.5%+5dgt) 50Hz ~ 300Hz
±(1.5%+5dgt) 50Hz ~ 500Hz *
DC Accuracy : ±(0.5% + 2dgt) Over voltage protection : 1000V DC or 750 V ACrms. Input Impedance : 10M // less than 100pF. * CMRR / NMRR : (Common Mode Rejection Ratio)
(Normal Mode Rejection Ratio) VAC : CMRR > 60dB at DC, 50Hz / 60Hz VDC : CMRR > 100dB at DC, 50Hz / 60Hz NMRR > 50dB at DC, 50Hz / 60Hz AC Conversion Type : Average sensing rms indication.
AC conversions are ac-coupled, true rms responding, calibrated to the sine wave input.
* The minimum LCD reading is 1400 count in Auto Ranging Mode.
Crest Factor : C.F. = Peak / Rms + 1.5% addition error for C.F. from 1.4 to 3 + 3% addition error for C.F. from 3 to 4
DC / AC Current (For 62, 62T only)
Range 2.000A 10.00A
DC Accuracy AC Accuracy VoltageBurden
±(1.0% + 3 dgt)
±(1.5% + 5 dgt) 50Hz~500Hz *
2V max
Overload Protection : A input : 10A (500V) fast blow fuse * AC Conversion Type : Conversion type and additional specification are same as DC/AC Voltage.
61/62/62T
EN
Ampere Testing Duty Ratio Table
Ampere 10A 9A 8A 7A 6A 5A
Testing Time 1min 2min 3min 4min 5min
Continually
Rest Time 10min 10min 10min 10min 10min N/A
Resistance
Range 200.0 ~ 200.0K
2.000M 20.00M *
Accuracy ±(0.7% + 3 dgt) ±(1.0% + 3 dgt) ±(1.5% + 3 dgt)
Open circuit Voltage : -1.3V approx. * There is a little rolling less then ±2%
Voltage Burden 600V rms
Diode Check and Continuity
Range
Resolution 10mV
Accuracy ±(1.5%+5dgt)*
* For 0.4V ~ 0.8V Max.Test Current : 1.5mA Max. Open Circuit Voltage : 2V Overload Protection : 600V rms Continuity: Built-in buzzer sounds when measured resistance is less than 270 and sound off when measured resistance is more than >850. Between 270 to 850 the buzzer maybe sound or off either.
Frequency (For 62, 62T only)
Range
Sensitivity
Accuracy
2000Hz~200.0KHz >1.5 Vac rms, <5 Vac rms Frequency : 2.000MHz~20.00MHz >2 Vac rms, <5 Vac rms 0.01%±2digit
61/62/62T
EN
Overload Protection : 600V rms. Minimum pulse width : >25 ns Duty cycle limits : >30% and <70%
Capacitance (For 62, 62T only)
Range 2.000nF ~ 200.0F
2.000mF *
Accuracy ±(1.9% + 8 dgt)
Overload Protection 600V rms
* < 10 dgt of reading rolling.
Temperature (°C ) (For 62T only)
Temperature -20°C ~ 0°C 1°C ~ 100°C 101°C ~ 500°C 501°C ~ 800°C
Accuracy ±(2% + 4°C ) ±(1% + 3°C ) ±(2% + 3°C ) ±(3% + 2°C )
Overload Protection 600V rms
Temperature (°F) (For 62T only)
Temperature -4°F ~ 32°F 33°F ~ 212°F 213°F ~ 932°F 933°F ~ 1472°F
Accuracy ±(2% + 8°F) ±(1% + 6°F) ±(2% + 6°F) ±(3% + 4°F)
Overload Protection 600V rms
61/62/62T
EN
Specifications
General Specifications
Display : 2000 counts. Polarity Indication : Automatic, positive implied, negative indicated.
Overrange Indication : "OL" or "-OL". Batteries Life : Alkaline 250 hours Low Batteries Indication : "<" is displayed when the batteries voltage drops below operating voltage.
Auto Power Off : Approx 10 minutes. Operating Ambient : Non-condensing ° 50°F, 51.8°F ~ 86°F (°80% R.H) 87.8°F ~ 104°F (°75% R.H), 105.8°F ~ 122°F (°45% R.H) Storage Temperature : -4°F to 140°F , 0 to 80% R.H. when battery removed from Meter.
Temperature Coefficient : 0.15 x (Spec.Accy) / °F ,< 64.4°F or > 82.4°F. Measure : Samples 2 times per second nominal. Altitude : 6561.7 ft (2000m) Safety : Complies with EN61010-1, UL61010-1, IEC 61010-1, V/ : CAT.III. 600V, CAT.II. 1000V. A : CAT.III. 500V (for 62/62Tonly) Pollution degree : 2 Power Requirements : 1.5V x 2 IEC LR03, AM4 or AAA size Dimensions (W x H x D) : 74mm x 156mm x 44mm Weight : (320g) including battery. Accessories : Battery (installed), Test leads and user manual.
61/62/62T
TC
· · · · · A ·
·
·
· · 30 42
60 · · · ·
61/62/62T
TC
·
· / /
A / /Hz
·
·
A
61/62/62T
TC
/
61/62/62T
TC
( 6262T )
C = C -C
/ ( 6262T )
1
1
61/62/62T
TC
/ ( 6262T )
°C ,°F
61/62/62T
TC
1
1
1
( )
10
61/62/62T
TC
( )
1. 2. 3. LED
4. 50~600 (50~500 ) LED
61/62/62T
TC
( 6262T )
· ·10 500
· · 1.5
61/62/62T
TC
23° C ± 5° C < 80%RH ±(% + )
DC AC
200.0mV * 2.000V * 20.00V ~ 200.0V * 750V AC 1000V DC
AC
±(1.5%+5 ) 50Hz ~ 300Hz
±(1.5%+5 ) 50Hz ~ 500Hz*
DC ±(0.5% + 2 ) DC 1000V AC 750 V RMS 10M // 100pF * CMRR NMRR
VAC DC CMRR > 60dB 50Hz / 60Hz VDC DC CMRR > 100dB 50Hz / 60Hz DC NMRR > 50dB 50Hz / 60Hz AC AC * LCD 1400
C.F. = 1.5% 1.4 3 C.F. +3% 3 4 C.F.
DC AC 6262T
2.000A 10.00A
DC
AC
±(1.5% + 5 ) ±(1.0% + 3 )
50Hz~500Hz *
2V
A 10A (500V) * AC DC AC
61/62/62T
TC
10A 9A 8A 7A 6A 5A
1 2 3 4 5
10 10 10 10 10
200.0 ~ 200.0 K
2.000M 20.00M *
±(0.7% + 3 ) ±(1.0% + 3 ) ±(1.5% + 3 )
-1.3V * ± 2%
600V rms
10mV
±(1.5%+5dgt)*
* 0.4V ~ 0.8V 1.5mA 2V 600V rms 270 850 270 850
6262T
2000Hz~200.0KHz >1.5 Vac rms <5 Vac rms
2.000MHz~20.00MHz >2 Vac rms <5 Vac rms 0.01% ±2
61/62/62T
TC
600V rms >25 ns : >30% <70%
6262T
2.000nF ~ 200.0F
2.000mF *
±(1.9% + 8 )
* < 10
° C 62T
-20 ° C ~ 0 ° C 1 ° C ~ 100 ° C 101 ° C ~ 500 ° C 501 ° C ~ 800 ° C
±(2% + 4 ° C) ±(1% + 3 ° C) ±(2% + 3 ° C) ±(3% + 2 ° C)
° F 62T
-4° F ~ 32° F 33° F ~ 212° F 213° F ~ 932° F 933° F ~ 1472° F
±(2% + 8° F) ±(1% + 6° F) ±(2% + 6° F) ±(3% + 4° F)
600V rms
600V rms
600V rms
61/62/62T
TC
2000 OL-OL 250 50 51.8 ~ 86 ( 80% ) 87.8 ~ 104 ( 75% ) 105.8 ~ 122 ( 45% ) -4 140 0 80% 0.15 ( ) / < 64.4 > 82.4 6561.7 (2000 ) EN61010-1UL61010-1IEC 61010-1, / CAT.III. 600VCAT.II. 1000V CAT.III. 500V ( 62/62T )
2 1.5 IEC LR03AM4 AAA ( x x )74 x 156 x 44 (320 ) ( )
61/62/62T
SC
· · · · · A ·
·
·
· · 30 42
60 · · · ·
61/62/62T
SC
·
· / /
A / /Hz
·
·
A
61/62/62T
SC
/
61/62/62T
SC
( 6262T )
C = C -C
/ ( 6262T )
1
1
61/62/62T
SC
/ ( 6262T )
°C ,°F
61/62/62T
SC
1
1
1
( )
10
61/62/62T
SC
( )
1. 2. 3. LED
4. 50~600 (50~500 ) LED
61/62/62T
SC
( 6262T )
· ·10 500
·
· 1.5
61/62/62T
SC
23° C ± 5° C < 80%RH ±(% + )
DC AC
200.0mV * 2.000V * 20.00V ~ 200.0V * 750V AC 1000V DC
AC
±(1.5%+5 ) 50Hz ~ 300Hz
±(1.5%+5 ) 50Hz ~ 500Hz*
DC ±(0.5% + 2 ) DC 1000V AC 750 V RMS 10M // 100pF * CMRR NMRR
VAC DC CMRR > 60dB 50Hz / 60Hz VDC DC CMRR > 100dB 50Hz / 60Hz DC NMRR > 50dB 50Hz / 60Hz AC AC * LCD 1400
C.F. = 1.5% 1.4 3 C.F. +3% 3 4 C.F.
DC AC 6262T
DC
AC
2.000A
±(1.5% + 5 )
±(1.0% + 3 )
10.00A
50Hz~500Hz *
2V
A 10A (500V) * AC DC AC
61/62/62T
SC
10A 9A 8A 7A 6A 5A
1 2 3 4 5
10 10 10 10 10
200.0 ~ 200.0 K
2.000M 20.00M *
±(0.7% + 3 ) ±(1.0% + 3 ) ±(1.5% + 3 )
-1.3V * ± 2%
600V rms
10mV
±(1.5%+5dgt)*
* 0.4V ~ 0.8V 1.5mA 2V 600V rms 270 850 270 850
6262T
2000Hz~200.0KHz >1.5 Vac rms <5 Vac rms
2.000MHz~20.00MHz >2 Vac rms <5 Vac rms 0.01% ±2
61/62/62T
SC
600V rms : >25 ns : >30% <70%
6262T
2.000nF ~ 200.0F
2.000mF *
±(1.9% + 8 )
* < 10
° C 62T
-20 ° C ~ 0 ° C 1 ° C ~ 100 ° C 101 ° C ~ 500 ° C 501 ° C ~ 800 ° C
±(2% + 4 ° C) ±(1% + 3 ° C) ±(2% + 3 ° C) ±(3% + 2 ° C)
° F 62T
-4° F ~ 32° F 33° F ~ 212° F 213° F ~ 932° F 933° F ~ 1472° F
±(2% + 8° F) ±(1% + 6° F) ±(2% + 6° F) ±(3% + 4° F)
600V rms
600V rms
600V rms
61/62/62T
SC
2000 OL-OL 250 50 51.8 ~ 86 ( 80% ) 87.8 ~ 104 ( 75% ) 105.8 ~ 122 ( 45% ) -4 140 0 80% 0.15 ( ) / < 64.4 > 82.4 6561.7 (2000 ) EN61010-1UL61010-1IEC 61010-1, / CAT.III. 600VCAT.II. 1000V CAT.III. 500V ( 62/62T )
2 1.5 IEC LR03AM4 AAA ( x x )74 x 156 x 44 (320 ) ( )
61/62/62T
JP
· · · · ·A · · · · ·30Vacrms42 Vac 60Vdc · < · · ·
61/62/62T
JP
·
· / /
A/ /
Hz
·
·
A
DC AC EU
61/62/62T
JP
AC / DC
61/62/62T
JP
6262T
C = C - C
6262T
61/62/62T
JP
DC / AC 6262T
°C ,°F
61/62/62T
JP
10
61/62/62T
JP
1. 2. 3. LED 4. 50V 600V50 500Hz LED
61/62/62T
JP
6262T
· · 10A500V
:
· · 1.5Vx 2
61/62/62T
JP
80% 23° C±5° C ± % +
DC/AC
200.0mV * 2.000V * 20.00V ~ 200.0V * 750V AC / 1000V DC
AC ±(1.5%+5 ) 50Hz ~ 300Hz
±(1.5%+5 ) 50Hz ~ 500Hz *
DC ±(0.5% + 2 ) 1000V DC 750 V AC RMS 10M // 100pF * CMRR / NMRR( )
( ) VACDC CMRR > 60dB50Hz / 60Hz VDCDC CMRR > 100dB50Hz / 60Hz DC NMRR > 50dB50Hz / 60Hz AC RMS AC AC * LCD 1400 / 1.4 ~ 3 +1.5% 3 ~ 4 3%
DC/AC 6262T
DC
AC
2.000A 10.00A
±(1.0% + 3 )
±(1.5% + 5 ) 50Hz~500Hz *
2V
A 10A (500V) * AC DC/AC
61/62/62T
JP
10A 9A 8A 7A 6A 5A
1 2 3 4 5
10 10 10 10 10
200.0 ~ 200.0K
2.000M 20.00M*
±(0.7% + 3 ) ±(1.0% + 3 ) ±(1.5% + 3 )
600V
-1.3V * ±2%
10mV
±(1.5%+5dgt)*
* 0.4V ~ 0.8V 1.5mA 2V 600V 270 850 270~850
61/62/62T
JP
6262T
2000Hz~200.0KHz 2.000MHz~20.00MHz
>1.5 Vac <5 Vac
>2 Vac <5 Vac
0.01%
±2
600V >25 >30% <70%
6262T
2.000nF 200.0F 2.000mF*
±(1.9% + 8 )
600V
* < 10
° C62T
-20° C ~ 0° C
±(2% + 4° C)
1° C ~ 100° C
±(1% + 3° C)
101° C ~ 500° C
±(2% + 3° C)
501° C ~ 800° C
±(3% + 2° C)
600V
° F62T
-4° F ~ 32° F 33° F ~ 212° F 213° F ~ 932° F 933° F ~ 1472° F
±(2% + 8° F) ±(1% + 6° F) ±(2% + 6° F) ±(3% + 4° F)
600V
61/62/62T
JP
2000 OL-OL 250 " " 10 50 51.8 86 80 R.H 87.8 104 75 R.H105.8 122 45 R.H -4 140 R.H. 0 80 0.15 xSpec.Accy/ <64.4 > 82.4 1 2 6561.7 2000m EN61010-1UL61010-1IEC61010-1 V /CAT.III 600VCAT.II 1000V ACAT.III 500V62 / 62T
2 1.5V x 2 IEC LR03AM4 AAA x x 74mm x 156mm x 44mm 320g
61/62/62T
RU
. , ; , , .
· , . · , . · , ; , . · , . · , A. · , . . · , , , . · , . . · , . · 30 Vac rms, 42 Vac , 60 Vdc. . · , , , . · , , . · , . · , .
61/62/62T
RU
!
·
.
· ,
/
/
A / / Hz .
·
.
·
A
,
.
, .
.
. , . .
. .
61/62/62T
RU
/
61/62/62T
RU
( 62, 62T)
, , .
=
/ ( 62, 62T)
>1
>1
61/62/62T
RU
/ ( 62, 62T)
°C ,°F
61/62/62T
RU
>1
>1
>1
- ( )
10
61/62/62T
RU
( )
1. . 2. . 3. «Volt sense». , , , . , . 4. 50 600 ( 50 500 ) , .
61/62/62T
RU
( 62, 62T) . :
!
· , , . · : 10, 500
. :
!
· , " " . · : 1,5 x 2
61/62/62T
RU
± (% + ) 23 ± 5°C . 80 %.
. /.
200,0 * 2,000 * 20,00 ~ 200,0 * 750 . / 1000 .
.
±(1,5%+5 . ) 50 ~ 300
±(1,5%+5 . ) 50 ~ 500*
DC: ± (0,5 % + 2 . ) : 1000 750 . : 10 // 100 * CMRR / NMRR:
( ) ( ) . : CMRR > 60 . , 50/60 . : CMRR > 100 . , 50/60 NMRR > 50 . , 50/60 : , . , , . * - - 1400- : = / +1,5% 1,4 3 3% 3 4
61/62/62T
RU
./. ( 62, 62T)
. .
2,000A 10,00
± (1,0 % + 3 . )
± (1,5 % + 5 )
50~500 *
. 2
: A: 10 (500) * : , / .
10A 9A 8A 7A 6A 5A
1 2 3 4 5
10 10 10 10 10 /
200,0 ~ 200,0 ± (0,7 % + 3 . )
2.000
± (1,0 % + 3 . )
20,00 *
± (1,5 % + 3 . )
: . -1,3. * ± 2%
600
61/62/62T
RU
10mV
±(1.5%+5dgt)*
* 0,40,8 . : 1,5 : 2 : 600 : , 270; , 850. 270 850 , .
2000~200,0
>1,5 . , <5 .
2,000~20,00
>2 . , <5 .
: 0,01% ± 2 .
: 600. : >25 : >30% <70%
( 62, 62T)
2,000 ~ 200,0 ± (1,9 % + 8 .
2,000
)
600
* < 10 . .
(°C ) ( 62T)
-20 0°C 1 100°C 101 500°C 501 800°C
±(2% + 4°C) ±(1% + 3°C) ±(2% + 3°C) ±(3% + 2°C)
600
61/62/62T
RU
(°F ) ( 62T)
-4 32°F 33 212°C 213 932°C 933 1472°C
±(2% + 8°C) ±(1% + 6°C) ±(2% + 6°C) ±(3% + 4°C)
600
: 2000 . : , , . : «OL» «-OL». : 250 : , . -: 10 . : < 50° F, 51,8° F ~ 86° F ( 80%) 87,8° F ~ 104° F ( 75%), 105,8° F ~ 122° F ( 45%) : -4° F 140° F, 0 80%, . : 0,15 x ( ) / °F, < 64,4° F > 82,4° F. : 2 . : 6561,7 (2000 ) : EN61010-1, UL61010-1, IEC 61010-1, / : III. 600 , II. 1000. A: .III. 500 ( 62 / 62T)
: 2 : 1,5 x 2, IEC LR03, AM4 AAA ( x x ): 74 x 156 x 44 : (320 ), . : (), .
www.appatech.com
APAC MGL APPA Corporation
cs.apac@mgl-intl.com Flat 4-1, 4/F, No. 35, Section 3 Minquan East Road, Taipei, Taiwan Tel: +886 2-2508-0877
: : : : : : : : 35 4 : cs.apac@mgl-intl.com : 02-2508-0877
72 400-099-1987 cs.cn@mgl-intl.com
700029264
Adobe PDF Library 17.0 Adobe InDesign 18.1 (Windows)