Owner's Manual for iBoard models including: IB-234C and H 6 Inches Running Boards Nerf Bars Side Steps, IB-234C and H, 6 Inches Running Boards Nerf Bars Side Steps, Running Boards Nerf Bars Side Steps, Boards Nerf Bars Side Steps, Nerf Bars Side Steps, Bars Side Steps, Side Steps, Steps
APS (304 Stainless Steel Polished Silver 6 inches Running Boards Nerf Bars Side Steps Compatible with Ford Expedition 2018-2024 (Exclude Max Model) : Automotive
Auto Parts & Auto Accessories - Over 4000 Auto Parts, Aftermarket Parts, Truck Accessories & Car Accessories
iBoard® iBoard® by APS READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED. *ROCKER PANEL MOUNT *NO DRILLING REQUIRED PART#: IB-234C&H Fastener Size Tightening Torque (ft-lbs) 6mm 6-7 8mm 16-18 10mm 31-32 12mm 56-58 14mm 92-94 Required X X X X PART LIST Driver Side Step Bar Front Passenger Side Step Bar 1# 1# 2# 2# 2# 2# Customer Support: info@iboardauto.com 1 Rev. 20230701 iBoard® Mounting Bracket List Item QTY Description Item QTY Description 1# 2 Driver & Passenger Front Mounting Brackets 2# 4 Mounting Brackets Hardware Package A (For Bracket Installation) Item QTY Description Item QTY Description 1# 12 M8 Plastic Washers 3# 12 M8 Nylon Lock Nuts 2# 12 M8 Flat Washers 1# 2# 3# Hardware Package B (For Stainless Steel Step Bar Installation) Item QTY Description Item QTY Description 1# 12 M8X1.25-35mm Carriage Bolts 3# 12 M8 Nylon Lock Nuts 2# 12 M8 Large Flat Washers 4# 6 Sliders (Packed with Step Bars) 1 # 2 # 3 # 4 # Customer Support: info@iboardauto.com 2 Rev. 20230701 iBoard® STEP 1 Start installation from the passenger side front of the vehicle. Locate the rear factory running board mounting location along the inner side of the body, (Fig 1). STEP 3 Select (1) Passenger Front Mounting Bracket. Attach the Passenger Front Mounting Bracket to the (2) factory studs with (2) M8 Flat Washers and (2) M8 Nylon Lock Nuts, (Fig 3). Do not fully tighten hardware at this time. Front (Fig 1) Passenger Side Front Mounting Location STEP 2 Slide (1) M8 Plastic Washer over each of the (2) factory mounting studs in the body panel, (Fig 2). IMPORTANT: The M8 Plastic Washers are designed to prevent corrosion between the aluminum body panel and the steel Mounting Brackets. Note: Do not install the Brackets without the Plastic Washers. (2) M8 Plastic Washers Rear (Fig 2) Thread M8 Plastic Washers Onto (2) Mounting Studs (2) M8 Plastic Washers (2) M8 Flat Washers (2) M8 Nylon Lock Nuts (Fig 3) Passenger Front Mounting Bracket Installation STEP 4 Move to the passenger side center & rear of the vehicle. Select (1) Mounting Bracket. NOTE: All (4) Mounting Brackets will fit left or right side. Repeat Steps 1--3 to install the passenger side Center & Rear Mounting Brackets. STEP 5 Once all (3) Passenger side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 4 & 5) (1) Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts; (2) Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider. (3) Slide the Slider (with carriage bolts) to the Step Bar. (4) Repeat to install the other (2) sliders to the step bar. (5) Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brackets. Secure the Step Bar to the installed Brackets by using (6) M8 Large Flat Washers and (6) M8 Nylon Lock Nuts and (3) Customer Support: info@iboardauto.com 3 Rev. 20230701 iBoard® Sliders, (Fig 5). Do not fully tighten hardware at this time. Note: The Sliders are packed with the Step Bars. Level and adjust the Step Bar and fully tighten all hardware. Repeat Steps 1-5 for the other side Step Bar installation. The installation is completed!!! Attention Do periodic inspections to the installation to make sure that all hardware is secure and tight. In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only. Slider (2) Carriage Bolts (Fig 4) Slider Installation Slider with (2) Carriage Bolts Step Bar Slider (w/ installed Carriage Bolts) Step Bar (Bottom View) Mounting Bracket (2) M8 Large Flat Washers (2) M8 Nylon Lock Nuts (Fig 5) Step Bar Installation Customer Support: info@iboardauto.com 4 Rev. 20230701Microsoft Publisher LTSC