User Manual for SKYDANCE models including: CXR-21A, CXR-28A, RF Constant Current LED Driver, CXR-28A RF Constant Current LED Driver, Constant Current LED Driver, Current LED Driver, LED Driver, Driver
75W 4CH 24VDC CV Wireless Dim &switchDim LED Driver PB-75-24-4
RF Constant Current LED Driver Model No.: CXR-21A,CXR-28A Features Special for magnetic & linear lamp No input polarity DC to DC constant current output, multiple output current settings Match with RF 2.4G dimming remote control Synchronize on multiple number of LED drivers Suitable for STUCCHI standard housings, magnetic installation Smooth dimming without icker, quiet without noise Short circuit, overload, no-load and anti-reverse protection 5-year warranty Technical Parameters No flicker, no noise For STUCCHI standard housing - 9519-166-K - B 9519-166-K/W Installation guide Output Input Environment Protection Other Model Output Voltage Output Current Output Power Current Accuracy Dimming Range Channel num Dimming Interface Input Voltage Input Current Ef ciency(Typ) Standby Power Woking Temperature Storage Temp Working Humidity Overload Short Circuit Reverse connection Size Weight CXR-21A CXR-28A 10~42Vdc 150-500mA 350-700mA 1.5W- 21W 3.5W-29.4W ±5% 0~100% , 1024levelsdimming 1 RF2.4G 48Vdc±5%( Nopolarity) Max.0. 47A Max.0.65A 93% 95% <0.5W -20~50°C -40~80°C 20~95%RH,non-condensing When load voltage exceed its range, the current declines, auto recovers when the load is reduced. Shutdownautomaticallyifshortcircuitoccurs, auto recovers. Prevent dirver and load damage L125×W13.5×H10.8mm 10.5g±2g LED Current Selection Note: Please select the correct current through the DIP switch on the PCB board when the power is off. DIP Switch CXR-21A Output Current Output Voltage Output Power 150mA 10-42V 1.5-6.3W 200mA 10-42V 2-8.4W 250mA 10-42V 2.5-10.5W 300mA 10-42V 3-12.6W 350mA 10-42V 3.5-14.7W 400mA 10-42V 4-16.8W 450mA 10-42V 4.5-18.9W DIP Switch CXR-28A Output Current Output Voltage Output Power User Manual Ver 1.0.1 350mA 10-42V 3.5-14.7W 400mA 10-42V 4-16.8W 450mA 10-42V 4.5-18.9W 500mA 10-42V 5-21W 550mA 10-42V 5.5-23.1W 600mA 10-42V 6-25.2W 650mA 10-42V 6.5-27.3W 3 500mA 10-42V 5-21W ON OFF 700mA 10-42V 7-29.4W ON OFF CXR-21A,CXR-28ARFConstantCurrentLEDDriver Mechanical Structures and Installations LEDLED+ 125mm ON 12 3 13.5mm DIM+ DIM- DC48V Wiring Diagram DC48V 48VDC Power Supply AC100-240V LEDLED+ LED Light LEDLED+ LED Light LEDLED+ LED Light DC48V DC48V ON 12 3 ON 12 3 ON 12 3 DIM+ DIM- DIM+ DIM- DIM+ DIM- 10.8mm RF remote Page 1 Match Remote Control Match: Switch off the power of the LED dirver, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 3 times on the remote. The light blinks 3 times means match is successful. .Delete: Switch off the power of the LED driver, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times on the remote. The light blinks 5 times means all matched remotes were deleted. Dimming Curve PWM duty(%) 100 Gamma=1.6 90 80 70 60 50 40 30 20 10 10 20 30 40 50 60 70 80 90 100 Brightness(%) Malfunctions analysis & troubleshooting Malfunctions No light No response from the remote Causes 1. No power. 2. Wrong connection or insecure. 1. The battery has no power. 2. Beyond controllable distance. 3. The LED driver did not match the remote. Troubleshooting 1. Check the power. 2. Check the connection. 1. Replace battery. 2. Reduce remote distance. 3. Re-match the remote. User Manual Ver 1.0.1 CXR-21A,CXR-28ARFConstantCurrentLEDDriver Page 2Corel PDF Engine Version 16.1.0.843 CorelDRAW X6