Operation Instruction

TV Setup Instructions

Used in TV production operation is as follows:

1. Turn on the TV, switch to the "home page" interface.
2. Select "Settings" feature. "OK" to enter
3. Select "network setup" function. "OK" to enter;
4. Choose the "wireless network", "OK" to enter;
5. According to the needs, select "auto search", "manual connection", etc. Press the "OK" to enter
6. Choose their own after the AP name "OK" to enter, Enter the password.

Television system has the memory function, for the first time to use should be according to the above steps, later need not operation, boot automatically connected. If need to change the AP or change the mode of connection, need according to the above steps again.

FCC Compliance and Regulatory Information

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.

To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

Regulation information

(1) List of applicable FCC rules:

• a. FCC Part 15.247
• b. FCC Part 15.249

(2) Summarize the specific operational use conditions:

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. The host product manufacturer should state this information to the host instruction manual.

(3) Limited module procedures:

Not applicable.

(4) Trace antenna designs:

Not applicable.

(5) RF exposure considerations:

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This compliance to FCC radiation exposure limits for an uncontrolled environment, and minimum of 20cm separation between antenna and body. The host product shall show the same or similar statement to the end users.

(6) Antennas

(7) Label and compliance information:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

The end product must carry a physical label or shall use e-labeling followed KDB784748D01 and KDB 784748 stating “Contains Transmitter Module FCC ID: 2ANM3NTUDT4”.

The e-label instructions:

1. The information must be accessible in no more than three steps from a product's main or home menu.
2. Products must not require special accessories or supplemental plug-ins (e.g., the installation of a SIM/USIM card) to access the information.
3. The FCC ID, warning statements, or other information must be displayed electronically in a manner that is clearly legible without the aid of magnification.
4. Regulatory Information must be Secure.

Information on Test Modes and Additional Testing Requirements

The host manufacturer can use the software "SecureCRT" for access to the test modes. Connected to the computer through the serial port of the host product and enter the command as following. If it does not work, then the host product manufacturer should coordinate with the module manufacturer for access to test mode software.

Bluetooth:

cd data

Signaling mode:

• ./boots_srv &
• ./boots -c reset
• ./boots -c dut

Non-signaling mode:

EDR mode:

• ./boots_srv &
• ./boots -c reset
• ./boots -c pwrlvl 3 // pwrlvl 0---7
• ./boots -c rft -p 04 -c 0 -t 3D // BR mode -c channel
• ./boots -c reset
• ./boots -c pwrlvl 3 // pwrlvl 0---7
• ./boots -c rft -p 04 -c 78 -t 3D // BR mode -c channel

BLE mode:

• ./boots -c ble_tx -c 0 -p 0 // BLE ///// -c 0-39 -p 0 1 2
• ./boots -c reset
• ./boots -c ble_tx -c 39 -p 0 // BLE

WiFi test modes:

cd /data/

su

./wifitest -O

11 b 1M

./wifitest -t 0 -c 1 -R 1 -B 0 -s 1 -i 30 -S 0 -n 0 -p 5 -y 2 -Y 0 // -C channel

-p power

11 b 11M

./wifitest -t 0 -c 1 -R 6 -B 0 -s 1 -i 30 -S 0 -n 0 -p 15 -y 2 -Y 0

11g 6M

./wifitest -t 0 -c 1 -R 4 -B 0 -s 60 -i 30 -S 0 -n 0 -p 18.5 -y 3 -Y 0

11g 54M

./wifitest -t 0 -c 1 -R 12 -B 0 -s 60 -i 30 -S 0 -n 0 -p 18.5 -y 3 -Y 0

11N 20M MCS0

./wifitest -t 1 -c 1 -N 0 -B 0 -s 1 -g 0 -i 30 -S 0 -n 0 -p 17 -y 3 -Y 0 //-N 0-7 MCS0-MCS7

11N 40M MCS7

./wifitest -t 1 -c 3 -N 7 -B 1 -s 1 -g 0 -i 30 -S 0 -n 0 -p 17 -y 3 -Y 1 //-N 0-7 MCS0-MCS7

Related command instructions:

./wifitest -t 1 -c 3 -N 7 -B 1 -s 1 -g 0 -i 30 -S 400 -n 0 -p 17 -y 3 -Y 1 // -t 0-abg 1-n; -R 1M-16M data rate ; -c channel; -B bandwidth(0-20M ;1-40M); -S time sm;-p Tx power;-y antenna 1-TX0 2-TX1 3-TX0+TX1; -Y package 0-20M 1-40M

Guidance for Host Product Installation and Verification

The following provides guidance to host product when installing this module on how they may verify the end product:

1. If the modular transmitter has been fully tested by the module grantee on the required number of channels, modulation types, and modes, it should not be necessary for the host installer to re-test all the available transmitter modes or settings. It is recommended that the host product manufacturer, installing the modular transmitter, perform some investigative measurements to confirm that the resulting composite system does not exceed the spurious emissions limits or band edge limits (e.g., where a different antenna may be causing additional emissions).
2. The testing should check for emissions that may occur due to the intermixing of emissions with the other transmitters, digital circuitry, or due to physical properties of the host product (enclosure). This investigation is especially important when integrating multiple modular transmitters where the certification is based on testing each of them in a stand-alone configuration. It is important to note that host product manufacturers should not assume that because the modular transmitter is certified that they do not have any responsibility for final product compliance.
3. If the investigation indicates a compliance concern the host product manufacturer is obligated to mitigate the issue. Host products using a modular transmitter are subject to all the applicable individual technical rules as well as to the general conditions of operation in Sections 15.5, 15.15, and 15.29 to not cause interference. The operator of the host product will be obligated to stop operating the device until the interference has been corrected.

Additional testing, Part 15 Subpart B disclaimer:

The modular transmitter is only FCC authorized for the specific rule parts (FCC Part 15.247) list on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed when contains digital circuity.