User Guide for vtech models including: VM3261, Video Monitor, VM3261-2
3. Set Temperature selector knob to AIR FRY position. 4. Turn TIM
Quick start guide. VM3261. VM3261- ... (Manual control). Pan. (Parent unit remote control). Press and hold. Press and ... unit in the User's manual.
For VM3261-2 only If you are viewing baby unit , the POWER LED light of baby unit turns on. As baby unit is not being viewed, its POWER LED light flashes. NONoteTES • If you power on only one baby unit, your parent unit may display and the LINK LED light flashes.
Go to www.vtechphones.com to register your product for enhanced warranty support and the latest VTech product news.
VM3261 VM3261-2
Video Monitor
What's in the box
VM3261
VM3261-2
Quick start guide
1 Install thebattery
Specifications are subject to change without notice. © 2019 VTech Communications, Inc. All rights reserved. 11/19. VM3261-X_QSG_V5. Document order number: 96-012003-040-100
THIS SIDE UP
2 Connect the baby monitor
NOTES · The rechargeable battery is pre-installed in your parent unit. · Use only the power adapters supplied with this product. · Make sure the baby monitor is not connected to the switch controlled electric outlet. · Connect the power adapters in a vertical or floor mount position only. The adapters' prongs are
not designed to hold the weight of baby monitor, so do not connect them to any ceiling, underthe-table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets. · Make sure the parent unit, the baby unit and the power adapter cords are out of reach of children.
4 Positioning the baby monitor
> 3ft (1m)
Caution
· The default volume of your parent unit is level 3, and the maximum volume is level 5. If you experience high-pitched screeching noise from your baby monitor while positioning:
- Make sure your baby unit and parent unit are more than 1 meter (3 feet) apart, OR
- Turn down the volume of your parent unit.
3 Power on the baby monitor
Tilt (Manual control)
Press and hold
Pan (Parent unit remote control)
3ft (1m)
3ft (1m)
< 3ft (1m)
Note
· To avoid interference from other electronic devices, place your baby monitor at least 3 feet (1 meter) away from devices such as wireless routers, microwaves, cell phones and computers.
3ft (1m)
Slide the ON/OFF switch to power on your baby unit.
Press and hold to power on your parent unit.
6U]KXOTMUT 3OYKKTLUTIZOUT
5 Status check
Once you power on both your baby unit and parent unit, your parent unit displays image from the baby unit, and the LINK LED light turns on. The POWER LED light of baby unit turns on.
36OUYK]KKTXOLTUTMIZUOUTT
Basic operation - Parent unit
Talk to your baby unit
Press and hold TALK and speak to your parent unit. Your voice is transmitted to the baby unit.
Press and hold
Use the menu
Press MENU to enter the menu, or save a setting. You can use the parent unit for advanced settings or operations, such as to play or stop the baby unit lullaby, or to adjust the baby unit sound sensitivity.
While in the menu: · Press or to scroll among the menu options. · Press SELECT or to enter the desired submenu. · Press or to select an item. · Press SELECT to confirm your selection. · Press or to exit the submenu.
Adjust speaker volume
Press VOL+ / VOL- to adjust your parent unit speaker volume.
The sound sensitivity setting also affects the speaker volume. For details, refer to Sound sensitivity and sound activation.
Submenu Main menu
Pan, tilt, zoom
Press and hold or to pan or tilt the image leftward or rightward.
Turn off the screen
Press and hold LCD ON/OFF to switch off the screen. You can still hear sound from the selected baby unit.
Press to zoom in or out.
Long press
Tip
· Press any keys on the parent unit to turn on the screen again.
Press and hold
Overview - Parent unit
LED lights
VOL VOL + Speaker Power jack
Zoom / Back LCD ON/OFF Microphone Arrow keys MENU/SELECT On/off TALK
Stand
Sound sensitivity and sound activation
Adjust sound detection sensitivity
With sound sensitivity setting, you can choose to hear sounds from the baby unit all the time, or to hear sounds that exceed a certain level.
Parent unit
What
You may
setting
happens... experience...
What you could do...
Speaker volume: Low
Sensitivity: Highest [Default]
Speaker volume: MAX
Sensitivity: Low / Medium
Hear all sounds all the time, including background sounds.
Difficulty in hearing your baby's soft sounds if the background sounds are louder.
Only hear sounds that exceed the selected sound sensitivity level.
No sound; or sounds that cut in and out at times as the baby unit may not detect extra soft sounds.
· Increase parent unit's speaker volume, and lower sound sensitivity.
· If you are using a white noise machine or sound machine, set its volume to low, or relocate it to minimize background sounds.
Increase the sound sensitivity, and adjust the volume level if necessary.
For details, please see Adjust the sound sensitivity of the baby unit in the User's manual.
Sound activated screen
When sound activation is on, the parent unit screen stays off to save power when the baby unit detects no sound. Once the baby unit detects sounds that are louder than the chosen sound sensitivity level, the parent unit screen turns on automatically. It will then turn off again after 50 seconds of no sound detection.
Overview - Baby unit
Light sensor Camera
Infrared LEDs Microphone
ON/OFF LED light
ON/OFF switch
Power Jack
Speaker Antenna
Temperature sensor
Night vision
PAIR
Threaded socket
The baby unit has infrared LEDs that allow you to see your baby clearly at night or in a dark room. When the baby unit being viewed detects low light levels, the infrared LEDs are switched on automatically. The images from the baby unit are in black and white, and appears on the screen.
Notes
· It is normal if you see a short white glare on your parent unit screen as the baby unit is adapting to the dark environment.
· When the infrared LEDs are on, the images are in black and white. This is normal.
Tip
· Depending on the surroundings and other interfering factors, like lightings, objects, colors and backgrounds, the display resolution may vary. Adjust the baby unit's angle or place the baby unit at a higher level to prevent glare and blurry display.
Mount the baby unit (optional)
Notes
· Check for reception strength and camera angle before drilling the holes.
· The types of screws and anchors you need depend on the composition of the wall. .
Use a pencil to mark two holes in parallel. Make sure they are the same distance apart as the wall mount holes on the baby unit.
If you drill the holes into a stud, go to step 3. -ORIf you drill the holes into an object other than a stud, insert the wall anchors into the holes. Tap gently on the ends with a hammer until the wall anchors are flush with the wall.
Align the wall mount bracket and screws with the holes in the wall as shown. Tighten the screw in the middle hole first, so that the wall mount bracket position is fixed. You can tighten the other screw in the top hole.
Insert the screws into the holes and tighten the screws until only 1/4 inch of the screws are exposed.
Place the baby unit on the wall mount bracket. Tighten the screw into the threaded socket at the bottom to secure the baby unit.
Place the baby unit on the wall mount bracket. Tighten the screw into the threaded socket at the bottom to secure the baby unit. Align the holes on the wall mount bracket with the screws on the wall, and slide the wall mount bracket down until it locks into place.
You can maximize your baby unit's viewing angles by tilting the wall mount bracket. Hold the baby unit, and then rotate the knob in anticlockwise direction. This will loosen the joint of the wall mount bracket. Tilt your baby unit up or down to adjust to your preferred angle. Then, rotate the knob in clockwise direction to tighten the joint and secure the angle.
For VM3261-2 only
Status check - Two baby units
If you are viewing baby unit , the POWER LED light of baby unit As baby unit is not being viewed, its POWER LED light flashes.
turns on.
Note
· If you power on only one baby unit, your parent unit may display Press to switch to the baby unit you have powered on.
and the LINK LED light flashes.
Change different views - Patrol
Press MENU when the parent unit is idle. Press or to choose , then press SELECT or . Press or to choose , then press SELECT to confirm your selection.
10s
Change different views - Single-cam
Press to switch to another camera in SINGLE-CAM mode.
Press .
Adobe PDF Library 15.0 Adobe InDesign CC 14.0 (Windows)