Your Cell Phone Signal Booster Store | Bolton Technical
User Manual for WILSONPRO models including: A1000, Building Signal Booster, A1000 Building Signal Booster
WilsonPro A1000 Building Signal Booster | Bolton Technical
File Info : application/pdf, 20 Pages, 964.66KB
DocumentDocumentWilsonPro A1000 Cellular Signal Booster User Manual NEED HELP? boltontechnical.co.za 011 749 3085 ______ Index Package Contents 1 STEP 1: Preparation 2 STEP 2: Find The dBm Reading On Your Phone 3 STEP 3: Measure Signal Strength For Inside Antenna 4 STEP 4: Measure Signal Strength For Outside Antenna 5 STEP 5: Temporarily Mount The Outside Antenna 6 STEP 6: Connect The System 7 STEP 7: Compare Results 8 STEP 8: Permanently Mount The Outside Antenna 9 STEP 9: Permanently Mount The Inside Antenna 11 STEP 10: Route & Secure The Cable 12 Test System: Lights 13 Specifications 15 Safety Guidelines 16 Warranty 18 ________ Package Contents WilsonPro A1000 Inside Antenna Outside Antenna 3 Coax Cables (1m,10m,15m) Power Supply 2x Pole Mount Bracket Wall Mount Bracket Lightning Surge Protector This device may be operated ONLY in a fixed location for in-building use. The signal booster unit is designed for use in an indoor, temperature controlled environment (38 degrees Celsius) We recommend plugging in the power supply into a power strip to protect against power surges and installing a lightning surge protector that is earthed. 1 WilsonPro A1000 CELL PHONE SIGNAL BOOSTER ______ Step 1: Preparation You Will Need (tools not included) Make sure the following materials are prepared and ready for your installation. 2 to 3 hours 2 people (a person to help with antenna calibration) o Ladder o Phillips-head screwdriver o 10mm open-end wrench or adjustable wrench o Drill (if routing cable through wall) o Mounting Option A : 25cm diameter pole (#BT512631) or an existing pole o Recommended: Power Strip with surge protection NOTE: These instructions will walk you through a "soft" install process to find the optimal locations for the Inside and Outside Antennas, then through the process of the permanent installation. 2 CELL PHONE SIGNAL BOOSTER WilsonPro A1000 ______ Step 2: Find The dBm Reading On Your Phone Visit: https://www.boltontechnical.co.za/blogs/news/signalstrength iPhone® iOS 9 - 10.3.3 iPhone® iOS 11 - current Put your iPhone into field test mode. To do this dial *3001#12345#* then press call. 1 Hold down power button until you see 'Slide to Power Off'. 2 Then release the power button. 3 Hold the Home button until your main screen appears. If you want to check 3G/1x but your iPhone is picking up 4G/ LTE signal, go to Settings>Cellular>Cellular Data Options>Enable LTE>Select Off. After you system is set up, you can go back to the dots signal by once again dialing *3001#12345#* then pressing call. When the menu comes back up, tap "phone" in the top left corner of your phone. iOS 11 no longer displays the decibel (dBm) reading in `Field Test Mode'. Tip: Using the bar indicator on your cell phone can assist you in finding the strongest signal direction as well as placing calls in different locations. For changes/updates on this issue, periodically go to: www.boltontechnical.co.za/blogs/news/signalstrength iPhone is a registered trademark of Apple Inc. Android is a trademark of Google Inc. AndroidTM Settings > About Phone > Status or Network > Signal Strength or Network Type and Strength (exact options/wording depends on phone model). All Other Phones & Alternate Methods iPhone · OpenSignal is a free app that allows you to run a test of your iPhone's true speed · Speedtest by Ookla is another free app Android users: do a signal strength test and network speed test. · Network Cell Info Lite, available for free on the Google Play store, provides nearly real-time monitoring of cellular and WiFi signals 3 WilsonPro A1000 CELL PHONE SIGNAL BOOSTER ______ Step 3: Measure Signal Strength For Inside Antenna Placement Turn off your cell phone's WiFi to ensure you are checking the cellular connection. The dBm reading will be refreshed every 30-60 seconds. Want faster results? Once you have a reading, turn on airplane mode. Wait 15 seconds. Turn off airplane mode. The signal strength reading is refreshed. Walk around your home/office taking signal strength readings until you find the area that has the weakest reception, or number farthest away from zero. For example -100 is a weaker signal than -80. Users on iOS 11 and above will need to use an alternative method using the bar indicator on your cell phone and/or placing calls in different locations. Weakest Signal Number:___________ Weakest Signal Location: ___________ Place your Inside Antenna in this poor signal area. For best results, keep the Inside Antenna more than 45cm away from the booster. Having an accurate measurement of signal strength in decibels (dBm) is crucial when installing your system. Decibels accurately measure the signal strength you are receiving. Test both 3G and 4G signal for best results by turning the LTE off in the carrier settings of your device. SIGNAL STRENGTH EXCELLENT GOOD FAIR POOR DEAD ZONE 3G/1x (typically voice) 4G/LTE (typically data) 4 -70dBm -90dBm -71 to -85dBm -86 to -100dBm -101 to -109dBm -110dBm -91 to -105dBm -106 to -110dBm -111 to -119dBm -120dBm CELL PHONE SIGNAL BOOSTER WilsonPro A1000 ______ Step 4: Measure Signal Strength For Outside Antenna Placement This is the most critical step of the installation process because it will determine the overall performance of the booster system. Using the same method as Step 3, find the place with the strongest signal (number closest to zero) on the outside of your home. Users on iOS 11 and above will need to use an alternative method using the bar indicator on your cell phone and/or placing calls in different locations. The further apart the Inside Antenna is located from the Outside Antenna, the better. To determine the best location for your Outside Antenna, note the dBm reading in a variety of locations. Note: The Outside Antenna must be at least 6 meters vertical or 15 meters horizontal from the Inside Antenna for best performance. Make sure the Inside Antenna and Outside Antennas are facing away from each other. 5 WilsonPro A1000 CELL PHONE SIGNAL BOOSTER ______ Step 5: Temporarily Mount The Outside Antenna A B Use one of the two options to mount the Outside Antenna on the side of the house with the strongest signal. Note: Using an app like 'Open Signal' will help you point the Outside Antenna in the direction of the nearest cell phone tower. A Option (Best) B Option (Good) Note: The Outside Antenna must be at least 6 meters vertical or 15 meters horizontal from the Inside Antenna for best performance. Make sure the Inside Antenna and Outside Antennas are facing away from each other. 6 CELL PHONE SIGNAL BOOSTER WilsonPro A1000 ______ Step 6: Connect The System Outside Antenna 1 Connect the supplied Coax Cable to end of booster labeled Outside Antenna. Inside Antenna 2 Connect the supplied Coax Cable to end of booster labeled Inside Antenna. Warning: Do Not connect power supply to booster before connecting both outside and indoor antennas 3 Power up the Booster by connecting it to a power source. To protect Booster from power surges, connect to a power strip. 7 WilsonPro A1000 CELL PHONE SIGNAL BOOSTER ______ Step 7: Compare Results Using the field test mode described in step 3, measure the new signal strength and write it down here ___________. Compare this number with the original reading you took in the same part of the house. If the number is higher (closer to zero) than the original reading without booster, your booster is working. If it is not, look at the lights on the booster and the section at the end of this manual "Test System: Lights". Users on iOS 11 and above will need to use an alternative method using the bar indicator on your cell phone and/or placing calls in different locations. Did you know a signal increase in just 3dB is 2 times the power and signal amplification! Signal Strength EXCELLENT Signal Strength GOOD Signal Strength Signal Strength FAIR POOR Signal Strength DEAD ZONE CELL TOWER 3G/1x 4G/LTE -70dBm -90dBm Distance from Cell Tower -75dBm -90dBm -100dBm -108dBm -105dBm -115dBm -110dBm -120dBm DECIBEL GAIN 3dB 6dB 10dB 12dB 20dB POWER INCREASE 2 times the power and signal amplification 4 times the power and signal amplification 10 times the power and signal amplification 16 times the power and signal amplification 100 times the power and signal amplification 8 CELL PHONE SIGNAL BOOSTER WilsonPro A1000 ______ Step 8: Permanently Mount The Outside Antenna Option A : Outside Roof/Pole Mount (Best Option) Mount, or use an existing pipe in an optimal signal location. Watch out for power lines. Outside Antenna (pole mount) Drip Holes need to face down 15 meters hor6izomnetatelrfsorvebretsictapleorrformance Inside Antenna WilsonPro A1000 Mounting on existing roof exhaust pipe would be a good time-saver option. Drip Holes need to face down 9 WilsonPro A1000 CELL PHONE SIGNAL BOOSTER ______ (STEP 8 cont.) Option B : Mounting on side of roof (Good Option) Outside Antenna (flush mount) 6 meters vertical or 15 meters horizontal for best performance Inside Antenna WilsonPro A1000 Drip Holes need to face down If needed, cable clips can be purchased at most hardware stores 10 CELL PHONE SIGNAL BOOSTER WilsonPro A1000 ______ Step 9: Permanently Mount The Inside Antenna Position bracket on wall and use a pencil to mark the holes. Drill holes using 3/16 inch bit. Use anchors, washers and screws to attach Wall Bracket. Slip Inside Antenna onto the Wall Mount Bracket to secure. Wall Mount & hardware anchor & screw slide into mount anchor & screw drywall 11 WilsonPro A1000 CELL PHONE SIGNAL BOOSTER ______ Step 10: Route & Secure The Cable Secure cable on outside home/office. Some homes have eaves you can tuck the cable between the soffit and the exterior wall. If needed, cable clips/ties can be purchased at most hardware stores. Look out for entry points such as spaces between brick and roof, aircon ducts, existing conduits or cable lines or air vents. Cable running to Outside Antenna Most eaves you can tuck the cable between the soffit and the exterior wall Create cable loops to protect from lightning and prevent water leaks Lightning likes to travel in straight lines through a medium. A loop before the lightning surge protector creates a deviation from the lightning's desired path thus protecting the system. Also looping the cable before the entry point into home will allow water to drip down from the loop and not cause water damage in the home. 12 CELL PHONE SIGNAL BOOSTER WilsonPro A1000 ______ Test System: Lights Band 1 Band 3 Band 8 Each light corresponds to a frequency band. ! IMPORTANT: To get an accurate reading of the lights, unplug and re-plug the power supply from the Booster. No Lights Booster does not have power. Un-plug and securely re-plug in power supply. Fix Any Red Light Problems (red indicates oscillation) · If you are happy with coverage, red lights don't have to be resolved. · Solid Red = Band has shut off · Blinking Green/Red = Band has reduced gain skinny side facing Cell Tower 1 Verify Outside Antenna faces away from the Inside Antenna. Un-plug and re-plug in power supply. 2 Verify the Inside Antenna is at least 45cm from the Booster and pointed away from the Booster. Un-plug and re-plug in power supply. 3 Tighten all cable connections. You may want to undo and redo the connection completely. Unplug and re-plug in power supply. 4 BEST: Increase the distance (horizontally or vertically) between the Outside and Inside Antenna. Add cable if needed. Un-plug and replug in power supply. 13 WilsonPro A1000 CELL PHONE SIGNAL BOOSTER ______ (TEST SYSTEM: LIGHTS cont.) Fix Any Orange Light Problems (orange indicates a cell tower is close by) If you are happy with coverage, orange lights don't have to be resolved · Solid Orange = Band has shut off · Blinking Green/Orange = Band has reduced gain. 1 If the light is solid orange, the Outside Antenna must be adjusted (see below). Wait 10 seconds between adjustments for the lights to reset. · For Roof/Pole Mount Option = Rotate the Outside Antenna away from the strongest cellular signal in small increments (45°) until the light turns green. Unplug and re-plug power supply. · For All Other Mount Options = Change mount location. For example, if the Outside Antenna is a window mount, move the Outside Antenna to a wall outside the building to see if the lights turn green. Un-plug and re-plug power supply. 2 If the light is blinking green/orange, re-locate the Outside Antenna. Un-plug and re-plug power supply. All Green Lights? = Band is set up optimally. Verify you have good coverage. If you have green lights, but poor coverage: · Rotate the Outside Antenna in small increments (roof/pole mount only). Un-plug and re-plug power supply. · Move the Outside Antenna to a different location. Un-plug and re-plug power supply. · Change the method of mounting the Outside Antenna. Un-plug and re-plug power supply. 14 CELL PHONE SIGNAL BOOSTER WilsonPro A1000 ______ WilsonPro A1000 Specifications Product Model Number Connectors Antenna Impedance Frequency MHz Band 1 (2100) Power output for single cell phone UPLINK DOWNLINK B1 30dB 25dB Passband Gain (nominal) B1 74 Noise Figure (typical downlink/uplink) Power Requirements WilsonPro A1000-3G/4G 520002 N-Female 50 Ohms Band 3 (1800) B3 30dB 25dB B3 74 5 dB nominal 5.5V DC, 1.5A Band 8 (900) B8 30dB 25dB B8 66 ! Lightning Surge Protector To Outside Antenna Ground Wire (not included) To Signal Booster RECOMMENDED: INSTALLING THE LIGHTNING SURGE PROTECTOR INSTALL THE LIGHTNING SURGE PROTECTOR (LSP) CLOSE TO THE SIGNAL BOOSTER. ATTACH THE CABLE FROM THE OUTSIDE ANTENNA TO THE SURGE PROTECTOR. ENSURE THE LSP IS PROPERLY GROUNDED. 15 WilsonPro A1000 CELL PHONE SIGNAL BOOSTER ______ Safety Guidelines Warnings To uphold compliance with network protection standards, all active cellular devices must maintain at least 2 meters of separation distance from Inside Panel and Dome antennas and at least 1.2 meters of separation distance from desktop Antenna. Use only the power supply provided in this package. Use of a non-WilsonPro product may damage your equipment. The Signal Booster unit is designed for use in an indoor, temperature-controlled environment (less than 38 degrees Celsius). It is not intended for use in attics or similar locations subject to temperatures in excess of that range. RF Safety Warning: Any antenna used with this device must be located at least 20 centimeters from all persons. This is a CONSUMER device. The WilsonPro A1000 is an ICASA Approved and Registered Device. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST cease operating this device immediately if requested by ICASA or licensed wireless service provider. 16 CELL PHONE SIGNAL BOOSTER WilsonPro A1000 ______ Antenna Kit Options The following accessories are to be used with the WilsonPro A1000 Booster. INSIDE ANTENNA EXPANSION KITS BT512952 1 Extra PANEL antenna expansion kit: 1 x Wall mount panel antenna 1 x 2-way splitter 1 x 15m and 1x 0.5m cable lengths ended with connectors BT512969 1 Extra DOME antenna expansion kit: 1 x Ceiling mount dome antenna 1 x 2-way splitter; 1 x 15m and 1x 0.5m cable lengths ended with connectors BT512976 2 Extra PANEL antenna expansion kit: 2 x Wall mount panel antenna 1 x 3-way splitter 2 x 15m and 1 x 0.5m cable lengths ended with connectors BT512969 2 Extra DOME antenna expansion kit: 2 x Ceiling mount dome antenna 1 x 3-way splitter 2 x 15m and 1x 0.5m cable lengths ended with connectors BT512976 3 Extra PANEL antenna expansion kit: 3 x Wall mount panel antenna 1 x 4-way splitter 3 x 15m and 1 x 0.5m cable lengths ended with connectors BT512969 3 Extra DOME antenna expansion kit: 3 x Ceiling mount dome antenna 1 x 4-way splitter 3 x 15m and 1x 0.5m cable lengths ended with connectors 17 WilsonPro A1000 CELL PHONE SIGNAL BOOSTER ______ Warranty 1 YEAR WARRANTY WilsonPro Signal Boosters are warranted for one (1) year against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to Bolton Technical with a dated proof of purchase. Signal Boosters should be returned with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by Bolton Technical. Bolton Technical shall at its option either repair or replace the product. This warranty does not apply to any Signal Boosters determined by Bolton Technical to have been subjected to misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties. Replacement products may include refurbished WilsonPro products that have been recertified to conform with product specifications. RMA numbers may be obtained by contacting Customer Support DISCLAIMER: The information provided by WilsonPro is believed to be complete and accurate. However, no responsibility is assumed by WilsonPro for any business or personal losses arising from its use, or for any infringements of patents or other rights of third parties that may result from its use. Represented by Bolton Technical: Sole Distributors in South Africa Copyright © 2021 WilsonPro. All rights reserved. WilsonPro products covered by U.S. patent(s) and pending application(s). For patents go to: WilsonPro.com/us/patents NOT AFFILIATED WITH WILSON ANTENNA