Installation Guide for STARLINK models including: Mobility Mount Kit, Mount Kit, Kit
Starlink Gen 3 In Motion Metal Roof Mount – MobileMustHave.com
Kit Starlink estándar: guía de instalación - Centro de ayuda de Starlink
| MOBILITY MOUNT KIT MOBILITY MOUNT KIT What's in the Box Mobility Mount Recommended Tools Screwdriver Lag Screws 4x Bolts 4x Nyloc Nuts Sealing Washers 4x 4x Drill / Impact Driver Drill Bit Drill Bit Wrench Wrench Pen 5 mm (3/16 in) 9 mm (3/8 in) 14 mm 13 mm 140 mm (5.5 in) 185 mm (7.3 in) 60 mm (2.4 in) INSTALL SCREW INSTALLATION 1 | Download the Starlink App Scan the QR code to download the Starlink App. 2 | Find Mounting Location Your Starlink needs a clear view of the sky so it can stay connected with satellites as they move overheard. Objects that obstruct the connection between your Starlink and the satellite will cause service interruptions. Use the obstructions tool in your App to ensure you have selected a suitable mounting location. You will also want to ensure your Starlink is mounted in the correct orientation relative to your vehicle as shown below. 3| Remove Kickstand Squeeze the release tab and pull it away from its fixed location. INSTALL SCREW INSTALLATION 4 | Mark the Pilot Holes Identify the installation location on your vehicle and mark the location of the 4 holes on your mobility mount using a pen or pencil. 5 | Drill the Pilot Holes Drill the holes with a 5 mm (3/16 in) drill bit. A mounting surface of at least 1.5in thick is recommended. 5 mm (3/16 in) 38 mm (1.5 in) INSTALL SCREW INSTALLATION 6 | Screw Mount to Surface Install a washer on the end of each screw and secure the mount to surface. Using a 13mm (1/2 in) deep-welled socket is recommended. 7 | Route Cable Through Mobility Mount Route the Starlink cable through the opening in the mobility mount and out the front end. 8 | Plug in Cable and Install Starlink Plug the ethernet cable into your Starlink and ensure the ethernet cable is fully inserted. Slide your Starlink into the mount until it clicks into place. INSTALL SCREW INSTALLATION 9 | Secure Mount Using the screwdriver, drive in the two locking screws until hand tight. Removing Your Starlink If you need to remove your Starlink, back out the locking screws. Then push down on the release tab on the mount while pushing your Starlink away from you. INSTALL BOLT INSTALLATION 1 | Download the Starlink App Scan the QR code to download the Starlink App. 2 | Find Mounting Location Your Starlink needs a clear view of the sky so it can stay connected with satellites as they move overheard. Objects that obstruct the connection between your Starlink and the satellite will cause service interruptions. Use the obstructions tool in your App to ensure you have selected a suitable mounting location. You will also want to ensure your Starlink is mounted in the correct orientation relative to your vehicle as shown below. 3| Remove Kickstand Squeeze the release tab and pull it away from its fixed location. INSTALL BOLT INSTALLATION 4 | Mark the Pilot Holes Identify the installation location on your vehicle and mark the location of the 4 holes on your mobility mount using a pen or pencil. 5 | Drill the Pilot Holes Drill the holes with a 9 mm (3/8 in) drill bit. 9 mm (3/8 in) INSTALL BOLT INSTALLATION 6 | Secure Mount to Surface Install a washer on the end of each bolt and insert bolts through the mount and pre-drilled holes. Install a nut on the end of each bolt and secure the mount to surface. Using a 14 mm deep-welled socket is recommended. 7 | Route Cable Through Mobility Mount Route the Starlink cable through the opening in the mobility mount and out the front end. 8 | Plug in Cable and Install Starlink Plug the ethernet cable into your Starlink and ensure the ethernet cable is fully inserted. Slide your Starlink into the mount until it clicks into place. INSTALL BOLT INSTALLATION 9 | Secure Mount Using the screwdriver, drive in the two locking screws until hand tight. Removing Your Starlink If you need to remove your Starlink, back out the locking screws. Then push down on the release tab on the mount while pushing your Starlink away from you.Adobe PDF library 17.00 Adobe Illustrator(R) 24.0