Philips 7000 Series Garment Steamer

Introduction and Components

The Philips 7000 Series garment steamer is designed for efficient wrinkle removal. The package typically includes the garment steamer unit, a water tank (available in 100ml and 200ml capacities), a storage bag, a brush attachment for different fabric types, and a heat-resistant mat for safe placement.

Supported models include: STH7020, STH7030, STH7040, STH7050, STH7060.

The device features OptimalTEMP technology.

Safety Precautions

Always follow safety guidelines to ensure safe operation:

• Do not touch the hot steam plate [cross-mark].
• Avoid spraying steam directly onto skin [cross-mark].
• Never steam garments while wearing them [cross-mark].
• Ensure the steamer is used correctly for effective results [check-mark].
• Be aware of potential hazards: hot surfaces [warning-triangle], electrical hazards [electrical-hazard], and do not use if the power cord is damaged [power-plug-hazard].

Water Usage Guidelines

The appliance is designed to be used with tap water.

For areas with hard water: To prevent scale build-up and prolong the appliance's lifespan, it is recommended to mix tap water with an equal amount of distilled or demineralized water.

Warning: Do not use the following in the appliance, as they may cause water spitting, brown staining, or damage:

• Perfumed water
• Water from tumble dryers
• Vinegar
• Starch
• Descaling agents
• Ironing aids
• Chemically descaled water
• Other chemicals

Operating Your Garment Steamer

Getting Started:

• Plug the appliance into a power outlet [power-symbol].
• Press the steam setting button and the steam trigger simultaneously.
• The device will heat up in approximately 30 seconds.
• Select your desired steam setting: ECO for energy saving or MAX for maximum steam power.

Steaming Technique:

• For best de-wrinkling results, ensure the steam plate is in full contact with the garment.
• Hold the garment by the bottom edge and pull it to stretch it while steaming.

Placement:

• To protect your horizontal surfaces from direct contact with the hot steam plate, place the steamer head on a heat-resistant layer (e.g., a silicone mat) or lay it sideways on the surface.

Storage

After use, allow the appliance to cool down. The storage bag provided can be used to keep the steamer clean and protected.

Instructions show placing the garment on a hanger, steaming it, and then storing the steamer in its bag.

Descaling and Maintenance

Regular descaling is important for maintaining the performance and longevity of your garment steamer. Follow these steps:

1. Plug the appliance into a power outlet.
2. Press and hold the steam setting button and the steam trigger simultaneously until 2 LED lights blink.
3. Steam and hot water will be released for approximately 1 minute.
4. The ECO mode light will blink to indicate the product is back to heating up.
5. Wait for 1 minute.
6. Rinse the steam head.
7. Wait for 60 minutes for the device to cool down and dry.
8. Plug the appliance back in.
9. Press the steam button for 30 seconds to complete the process.

The appliance is suitable for use with tap water. For hard water areas, mixing with distilled or demineralized water is recommended to prevent scale build-up.

Support and Contact

If you encounter any problems or have questions regarding your Philips garment steamer, please visit the official Philips support website at www.philips.com/support. Here you can find a list of frequently asked questions (FAQs) or contact the Consumer Care Center in your country for further assistance.

Manufacturer Information and Specifications

Manufacturer: DAP B.V., Tuskeniepen 4 a, 9206 AD, Drachten, The Netherlands.

Technical Specifications:

• Power: 1372-1633W
• Voltage: 220-240V
• Frequency: 50-60Hz
• Appliance Class: I
• Operating Temperature: +0°C - +35°C
• Relative Humidity: 20% - 95%
• Atmospheric Pressure: 85 - 109kPa

Made in China

© 2021 Philips Domestic Appliances Holding B.V. All rights reserved.

Document Number: 4239.001.2200.1 (23/09/2021)