User Manual for LEAX ARKIVATOR TELECOM models including: MGA6230A, 2AVFNMGA6230A, 2AVFNMGA6230A, MGA6230A, MGA6230A CAT12 Industrial Grade LTE Module, CAT12 Industrial Grade LTE Module, Industrial Grade LTE Module, LTE Module
Leax Arkivator Telecom USA Inc. MGA6230A 2AVFNMGA6230A 2AVFNMGA6230A mga6230a
File Info : application/pdf, 9 Pages, 704.05KB
DocumentDocumentMGA6230A CAT12 Module User Manual MGA6230A Product User Manual MGA6230A Product User Manual MGA6230Amodule is an industrial-grade LTE module, which provides multiple bands support. This module can be adapted to various types of terminal devices, providing LTE network connection and data communication, such as industrial routers, industrial handsets, tablet computers, laptops, etc. Main Chipset GCT GDM7243A LTE Category Band support Antenna Tx/Rx CA/MIMO Modulation Power output 3GPP Release11 Cat12 B2/4/5/12/13/66/71 4 ANT PIN LTE: Main and Diversity antenna B2/4/66,2T4R B5/12/13/71,1T2R DL: 2CA intra band ,4x4 MIMO 2CA inter band ,2x2 MIMO 3CA&4CA,2x2 MIMO UL: 2CA 2x2MIMO Uplink: QPSK/16QAM/64QAM Downlink: QPSK/16QAM/64QAM/256QAM +23dBm (Power Class3) Throughput Interface Voltage Input Operating Temperature Storage Temperature DL: Max 600Mbps UL: Max 150Mbps USB 2.0&USB3.0 UARTSIM*1PCIERGMII GPIOSDIOSPIPCM 3.0VDC ~ 3.6VDC ( Recommend 3.3V) -40~+85 (Reduce RF performance: -40~-30, +70~+85) -40~+85 Fig. 1 - Detail module dimension Pin Definition Pin Description Pin Name Power 3.3V_VBAT VBAT_RF DCDC_1.8V DCDC_3.2V GND RESERVED Pins Pin No. Description I/O 27,28,29,30 Power supply for the module's baseband part PI 84,85 Power supply for the module's RF part PI 24 1.8V output power supply for external circuits PO 25 3.2V output power supply for external circuits PO 1~5,8~10,18,23,26, 31,36,40,44,49,50, 53,56,59,60,65,68, 76,81,82,83,86~97, 99~104,106~115,1 Ground 17,118,120~130,13 6,141,146,147,152, 156,160,166,167,1 75,176,181,188,19 3~457 Voltage Domain 3.0V-3.6V 3.3V-4.3V 1.8V 3.2V Pin Name Pin No. Description 6,7,61~64,66,67,75 RESERVER ,80,135,168~174,1 NC 86,191 USB Interface USB2.0_DM 51 USB differential data bus (-) USB2.0_DP 52 USB differential data bus (+) USB3.0_SSTX- 54 USB superspeed transmission (-) USB3.0_SSTX+ 55 USB superspeed transmission (+) USB3.0_SSRX- 56 USB superspeed receiving (-) USB3.0_SSRX+ 57 USB superspeed receiving (+) UART Interface UART1_TXD 137 UART serial data interface UART1_RXD 138 UART0_TXD 139 UART0_RXD 140 PCM Interface PCM_IN 79 PCM serial data interface PCM_OUT 192 PCM_SYNC 78 PCM_CLK 190 RGMII Interface RGMII_MDIO 32 RGMII MDIO management data RGMII_MDC 148 RGMII MDC management clock RGMII_RXD0 33 RGMII receive data bit 0 RGMII_RXD1 149 RGMII receive data bit 1 RGMII_RXD2 34 RGMII receive data bit 2 RGMII_RXD3 150 RGMII receive data bit 3 RGMII_RCTL 35 RGMII receive control RGMII_RCLK 151 RGMII receive clock RGMII_TXD0 37 RGMII transmit data bit 0 RGMII_TXD1 153 RGMII transmit data bit 1 RGMII_TXD2 38 RGMII transmit data bit 2 RGMII_TXD3 154 RGMII transmit data bit 3 RGMII_TCTL 39 RGMII transmit control RGMII_TCLK 155 RGMII transmit clock PHY_RESET_N 73 Reset output for RGMII PHY Other Interface Pins GPIO_0 11 General Purpose Input/Output I/O Voltage Domain AI/AO AI/AO AO AO AI AI DO 1.8V DI 1.8V DO 1.8V DI 1.8V DI 1.8V DO 1.8V DI 1.8V DO 1.8V IO 3.3V DO 3.3V DI 3.3V DI 3.3V DI 3.3V DI 3.3V DI 3.3V DI 3.3V DO 3.3V DO 3.3V DO 3.3V DO 3.3V DO 3.3V DO 3.3V DO 3.3V DIO 1.8V Pin Name Pin No. GPIO_1 12 GPIO_2 13 GPIO_3 14 GPIO_4 15 GPIO_5 16 GPIO_6 17 GPIO_7 131 GPIO_8 132 GPIO_9 133 GPIO_10 134 GPIO_D 69 GPIO_P 182 SLIC_INT# 189 SLIC_RESET# 77 PS_HOLD 187 HW_RST# 71 SW_RST# 185 WAKEUP#_MODULE 72 WPS_KEY 184 WIFI_RESET_N 183 GPS_RESET_N 70 DS_IND# 74 SDIO Interface SDH0_D3 41 SDH0_D2 157 SDH0_D1 42 SDH0_D0 158 SDH0_CMD 43 SDH0_CLK 159 RF Interface ANT0 98 ANT1 105 ANT2 116 ANT3 119 SPI Interface SPI_CS0# 19 SPI_MISO 20 SPI_CLK 21 Description I/O Voltage Domain DIO DIO DIO DIO DIO DIO DIO DIO DIO DIO DIO DIO SLIC INT DI SLIC reset DO Holding PMIC on state with ONOFF KEY. DO Turn on/off the module DI 3.3V Reset the module DI 1.8V Used to wake up the module DI WPS input DI WIFI reset DO GPS reset DO Enable external AP power supply DO Secure digital controller data bit 3 Secure digital controller data bit 2 Secure digital controller data bit 1 Secure digital controller data bit 0 SD command SD serial clock I/O 1.8V I/O 1.8V I/O 1.8V I/O 1.8V DO 1.8V DO 1.8V Main antenna 0,support TX and RX Receive diversity antenna interface1 Main antenna 2,support TX and RX Receive diversity antenna interface3 AI/AO AI AI/AO AI SPI chip select SPI master input salve output SPI clock DO 1.8V DI DO Pin Name Pin No. SPI_MOSI 22 JTAG Interface TDO 180 TDI 179 TMS 178 TCK 177 Pin Name Pin No. (U)SIM Interface SIM_RST 142 SIM_CLK 143 SIM_DAT 144 SIM_VCC 145 PCIe Interface PCIE_RXDN 45 PCIE_RXDP 46 PCIE_TXDN 47 PCIE_TXDP 48 PCIE_CLKREQ# 161 PCIE_REF_CLK 162 PCIE_W_DISABLE 163 PCIE_WAKE# 164 PCIE_RESET# 165 Description SPI master output slave input Test Data Out Test Data In Test Mode Select Test Clock Description Reset signal of (U)SIM card Clock signal of (U)SIM card Data signal of (U)SIM card Power supply for (U)SIM card PCIe receiving (-) PCIe receiving (+) PCIe transmission(-) PCIe transmission(+) PCIe clock request Output PCIe reference clock PCIE W_DISABLE PCIe wake-up PCIe reset Pin Direction Definition PI PO AI/AO AI AO DI/DO DI DO Power input Power output Both Analog input output Analog input Analog output Both Digital input and output Digital input Digital output I/O Voltage Domain DO DO DI DI DI I/O Voltage Domain DO 1.8V/3V DI 1.8V/3V DO 1.8V/3V PO 1.8V/3V AI AI AO AO DIO AIO DI DI DO DC Electrical Parameter Description Min VIH High-level input voltage 1.17 VIL Low-level input voltage -0.3 VOH high-level output voltage 1.6 VOL low-level output voltage 0 Power Consumption Max Unit VDD_IO V 0.63 V VDD_IO V 0.4 V Parameter Min Typical Max Unit TDD Band FDD Band 600 800 mA 800 1000 mA RF Performance Operating Band Band 2 Band 4 Band 5 Band 12 Band 13 Band 66 Band 71 Transmit Power (dBm) 23±2.7 23±2.7 23±2.7 23±2.7 23±2.7 23±2.7 23±2.7 Antenna Interface receiving sensitivity <95dBm @ 10MHz bandwidth <97dBm @ 10MHz bandwidth <95dBm @ 10MHz bandwidth <94dBm @ 10MHz bandwidth <94dBm @ 10MHz bandwidth <96.5dBm @ 10MHz bandwidth <94.2dBm @ 10MHz bandwidth FCC ID2AVFNMGA6230A This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INTEGRATION INSTRUCTIONS: This modular transmitter complies with FCC Rules Part 2, Part 22, Part 24, Part 27. Specific operational use conditions Antenna Change Notice to Host manufacturer Recommend using antenna which certified with this module mentioned in this manual. If you desire to increase antenna gain and either change antenna type or use same antenna type certified, a Class II permissive change application is required to be filed by us, or you (host manufacturer) can take responsibility through the change in FCC ID (new application) procedure followed by a Class II permissive change application, based on the new emissions testing. Please perform testing on frequency bands where the antenna gain is highest, worstcase band-edges based on original filing, and only on frequency bands where the antenna gain is highest. Notice regarding trace antenna to host product manufacturer Any deviation(s) from the defined parameters of the antenna trace, as described by this instruction, host product manufacturer must notify us that you wish to change the antenna trace design. In this case, a Class II permissive change application is required to be filed by us, or you (host manufacturer) can take responsibility through the change in FCC ID (new application) procedure followed by a Class II permissive change application. RF exposure compliance instruction: This module is limited to installation in mobile application with a minimum separation distance of at least 20 cm from a person's body, a separate approval is required for all other operating configurations, including portable configurations with respect to §2.1093 and different antenna configurations. Host product manufacturer shall at least provide information of minimum separation distance to end users in RF exposure compliance statement to end users in their end-product manuals. This module is tested with the following antenna Antenna Type Brand/ manufacturer Model No. Max. Antenna Gain Xxx e.g PIFA Applicable to limited Applicable to limited module module Xxx Labelling and compliance statement instruction for host product manufacturer Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: "Contains FCC ID: 2AVFNMGA6230A" any similar wording that expresses the same meaning may be used. § 15.19 Labelling requirements shall be complied on end user device. Labelling rules for special device, please refer to §2.925, § 15.19 (a)(5) and relevant KDB publications. For E-label, please refer to §2.935. FCC regulatory Compliance Statement mentioned in this manual shall be properly included in host product manual per FCC Rules. The host product manufacturer shall be aware not to provide information to the end user on how to install or remove this module in your host product manual. Guide on test modes and additional testing requirements Host product manufacturer is ultimately responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, additional transmitter(s) in the host, etc.). Disclaimer on additional testing, Part 15 Subpart B compliance of Host Product This modular transmitter is only FCC authorized for the specific rule parts listed on our grant, host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. Host manufacturer in any case shall ensure host product which is installed and operating with the module is in compliant with Part 15B requirements. Please note that For a Class B or Class A digital device or peripheral, the instructions furnished the user manual of the end-user product shall include statement set out in §15.105 Information to the user or such similar statement and place it in a prominent location of host product manual. Original texts from FCC Rules are as following you may refer to: For Class B Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. For Class A Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Disposal of Electronic and Electrical Waste Pursuant to the WEEE EU Directive, electronic and electrical waste must not be disposed of with unsorted waste. Please contact your local recycling authority for disposal of this product.Microsoft Word for Microsoft 365