WolfLaws TA2000 Wireless Gaming Headset User Manual

Introduction

The WolfLaws TA2000 wireless gaming headset features 50mm high-precision neodymium drivers and soft leatherette ear cups, providing an immersive sound quality for an extreme gaming experience. It is designed for FPS gaming and offers broad compatibility with PC, Laptop, PS4, and Mac via USB connection. Additional 3.5mm cable and Bluetooth functionality offer further versatility.

⚠️ To prevent possible hearing damage, do not listen at high volume levels for long periods.

Product Overview

The headset comprises an ergonomic headband, soft memory foam ear pads, an indicator light, a 2.4G/Bluetooth mode switch, a power button, a mic on/off button, and a volume control.

Headset Power/Mic Button

Headset Power Button

Power On/Off: Hold down the power button for 3 seconds until you hear an indicating voice. [power-symbol]

Play/Pause: Click the power button once. [play-pause-symbol]

Mic Mute Button

Mic On: Click the button once. [mic-on-symbol]

Mic Off: Click the button once. [mic-off-symbol]

Headset Charging

1. It is recommended to fully charge the headset before first use.

2. When the headset's battery level is low, you will hear a 'battery low' notification.

3. Connect the Type-C cable to the charging port on the headset and plug the other end into any USB power source.

Charge Status:

• Charging: Red Light On
• Charging Completed: Red Light Off

⚠️ CAUTION: Do not use the headset while charging.

Headset Connection

The headset can be connected via 2.4G wireless adapter or a 3.5mm jack.

2.4G Wireless Adapter Connection

For PC/Laptop/PS4/PS5/Mac: Connect the included 2.4G Wireless Adapter to a USB port on your device.

3.5mm Jack Connection

For PS4/PS5/Notebook/Mac: Use the included 3.5mm jack.

For XBOX ONE/S/Nintendo/Mobile: Use the included 3.5mm jack. For older Xbox One controllers, a Microsoft Adapter (not included) is required.

Operating Instruction

To use the wireless headset with your device (PC, PS4, PS5, laptop, Mac, XBOX ONE, Nintendo, Mobile):

1. Connect the wireless adapter (included) to a USB port on your device.
2. Plug the 3.5mm audio cable (included) into the headset and then connect it to your device (XBOX ONE/S, Nintendo, Mobile) if using a wired connection.
3. Press and hold the power button on the headset for 3 seconds to power on.
4. When the headset ear cup LED is solid, the headset is connected.

Note: If this is your first time using the headset, you may need to set it as the default input and output device in your system's audio settings.

PS4 Connection Steps:

1. Plug the 2.4G Wireless Adapter into the PS4 Gamepad.
2. Navigate to PS4 System Settings.
3. Select 'Devices', then 'Audio Devices'.
4. Under 'Output Device', choose 'USB Headset'.
5. For 'Output to Headphones', select 'All Audio'.
6. Adjust the 'volume control (headphones)'.
7. Confirm that all plugs are inserted firmly and fully.

XBOX ONE/XBOX ONE S Connection Steps:

1. Plug the 3.5mm cable (included) into the headset.
2. Connect the headset directly to Second Generation Xbox One Controllers.
3. For older version Xbox One Controllers, you will need an extra adapter (Not Included). Connect the headset to the 3.5mm port of the adapter, which is plugged into the controller.
4. Adjust or rotate the 3.5mm interface until both sides of the headphones produce smooth sound.

Information for Xbox One User:

• Controllers with a headset port: Headset Adapter Not Required. Works straight out of the box with the 3.5mm jack.
• Controllers with no headset port: Microsoft Stereo Headset Adapter Required.

Technical Specifications

• Working Voltage: 5V
• Battery Capacity: 800 mAh
• Dimension: 185*88*202mm
• Weight: 250±5g
• Charging Time: 2-3 hours
• Duration Time: >45 hours
• Charge Interface: Type-C

Troubleshooting Tips

No sound/low sound

• Possible Cause: Volume Control, Loose Connector, App Problem
• Solution: Press the Volume Up button on the headset. Check the Chat/Game Mix if applicable. Close the active App and re-open it. Confirm that each plug is inserted firmly and fully.

Microphone not working

• Possible Cause: Mic Button, Loose Connector
• Solution: Check that the mic one-key mute button on the headset is off. Ensure the headset is selected as the input device. Confirm that each plug is inserted firmly and fully.

Voice interrupted

• Possible Cause: Setting, Weak Signal
• Solution: Check that the default (input and output) sound device is selected for this headset. Check your network connection.

For any further questions, please feel free to contact WolfLaws through Amazon or email at sales@ibengoo.com.

Safety and Precautions

Carefully read all information in this manual and on the product packaging before use.

Safety

• Observe all warnings, precautions, and instructions.
• ⚠️ CHOKING HAZARD - Contains small parts. Keep out of the reach of small children.
• Stop using the headset immediately if you experience discomfort or pain in your head. Consult a doctor if the condition persists.
• Avoid prolonged use. Take breaks at approximately 15-minute intervals.
• Permanent hearing loss may occur if the headset is used at high volume. Set the volume to a safe level. Over time, loud audio may sound normal but can damage your hearing. If you experience ringing in your ears or muffled speech, stop listening and have your hearing checked.
• To protect your hearing: Limit usage time at high volume, avoid raising volume to block noise, and lower volume if you cannot hear people speaking nearby.
• If the headset irritates your skin, stop using it immediately.
• Do not disassemble or insert anything into the headset, as this may cause damage or injury.
• Observe all signs and instructions requiring electrical devices or radio products to be switched off in designated areas (e.g., gas stations, hospitals, potentially explosive atmospheres, aircraft).
• The battery used in this device may present a risk of fire or chemical burn if mistreated. Do not disassemble, heat above 60°C, or incinerate.

Compatibility Information

Note: Xbox One/S/X and older Xbox One controllers may require specific adapters for wired or wireless functionality as detailed in the connection sections.

FCC Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement: The device has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions without restriction.