Concession Supplies & Equipment | Gold Medal Products Co.
Concession Supplies & Equipment | Gold Medal Products Co.
Manual-Hub.com - Free English product PDF Documents!
Instruction Manual for GOLD MEDAL models including: 3052-00-001 Auto Breeze EZ Kleen Head, 3052-00-001, Auto Breeze EZ Kleen Head, Breeze EZ Kleen Head, EZ Kleen Head, Kleen Head
GOLD MEDAL AUTO BREEZE EZ KLEEN 3052-00-001 (01) PDF MANUAL - Manual-Hub.com
File Info : application/pdf, 29 Pages, 4.90MB
DocumentDocumentInstruction Manual Auto Breeze® EZ Kleen Head Model No. 3052-00-001 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA © 2018 Gold Medal Products Co. Part No. 110026 https://manual-hub.com/ Auto Breeze EZ Kleen Head Model No. 3052-00-001 SAFETY PRECAUTIONS DANGER Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death. DO NOT immerse any part of this equipment in water. DO NOT use excessive water when cleaning. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing. Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle. 008_051514 DANGER Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Any alterations to this equipment will void the warranty and may cause a dangerous condition. This appliance is not intended to be operated by means of an external timer or separate remote-control system. NEVER make alterations to this equipment. Read the Installation, Operating, and Maintenance Instructions thoroughly before installing, servicing, or operating this equipment. 014_020416 WARNING Floss head rotates at high speeds. Operator MUST keep hands and face clear of the floss head to avoid injury. Operator must wear eye protection. Keep all spectators at a reasonable distance, and use a Floss Bubble for added customer protection. 015_062714 WARNING Keep all foreign objects out of floss head. To avoid eye injury, DO NOT fill floss head with sugar while the head is on and rotating. 016_010914 WARNING Burn Hazard. DO NOT touch spinner head. Allow to cool before cleaning or servicing. Avoid contact with molten sugar. 006_092414 WARNING ALWAYS wear safety glasses when servicing this equipment. 010_010914 Page 2 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 SAFETY PRECAUTIONS (continued) WARNING No user serviceable parts inside. Refer servicing to qualified service personnel. 011_051514 WARNING Read and understand operator's manual and all other safety instructions before using this equipment. To order copies of the operator's manual go to gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862 022_060215 WARNING DO NOT allow direct contact of this equipment by the public when used in food service locations. Only personnel trained and experienced in the equipment operation may operate this equipment. Carefully read all instructions before operation. 012_010914 WARNING This machine is NOT to be operated by minors. 007_010914 Note: Improvements are always being made to Gold Medal's equipment. This information may not be the latest available for your purposes. It is critical that you call Gold Medal's Technical Service Department at 1-800-543-0862 for any questions about your machine operations, replacement parts, or any service questions. (Gold Medal Products Co. does not assume any liability for injury due to careless handling and/or reckless operation of this equipment.) General images may be used in manual for reference only. Page 3 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 INSTALLATION INSTRUCTIONS Inspection of Shipment After unpacking (reference unit Quick Start Guide), check thoroughly for any damage which may have occurred in transit. Claims should be filed immediately with the transportation company. The warranty does not cover damage that occurs in transit, or damage caused by abuse, or consequential damage due to the operation of this machine, since it is beyond our control (reference warranty in back of manual). Manual Read and understand the operator's manual and all other safety instructions before using this equipment. To order copies of the operator's manual go to gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862. Model Description 3052-00-001: Auto Breeze cotton candy machine with EZ Kleen Head and an aluminum floss pan. Items Included with this Unit Instruction Manual Registration Warranty Card Whirlgrip Floss Stabilizer (PN 3010) Aluminum Floss Pan (PN 42040) Page 4 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 Setup for Use (General reference images shown) Spinner Head Bell Housing Lock-N-Go Handle Step 1: Set unit on a level surface. DO NOT lift unit by spinner head. Step 2: Lock-N-Go® handles are used for transport. Rotate both handles to a vertical, UNLOCKED, position for use. This allows the bell housing to "float" freely on the springs during operation. DO NOT operate with handles in the transport position. 1 2 Quick Release Floss Cap Rubber Float Step 3: Place floss pan on unit. Step 4: Check the Rubber Floats; be sure they are fully inserted in float holders on Quick Release Floss Cap. Twist floaters to position shown to create a lifting action when making floss. Step 5: Install Floss Stabilizer (see instructions on next page). Unit should be cleaned prior to use (reference Care and Cleaning section of this manual). Page 5 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 Whirlgrip Floss Stabilizer Installation Instructions Unit must be OFF, and cool to install Floss Stabilizer. Place Floss Pan on unit and install Whirl Grip Floss Stabilizer (Item No. 3010) as shown below. Kit includes: Floss Stabilizer/screening (P/N 43032), and (6) Whirlgrip Clips (P/N 77470). Clips are designed to provide air space between screening and floss pan. Step 1: Place Whirl Clips over rim of pan with hooks facing inside. Step 2: Hang Stabilizer on top, up facing hook. Screening should be about flush with top of pan. Step 3: Gently pull screening down and attach to bottom, down facing hook. Allow air space for proper operation. Top View of Floss Pan Step 4: Repeat for all clips keeping equal spacing around pan (number of clips varies by model). Allow air space between pan and screening for proper operation. Page 6 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 Electrical Requirements The following power supply must be provided: 3052-00-001: 120 V~, 1440 W, 60 Hz DANGER Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death. DO NOT immerse any part of this equipment in water. DO NOT use excessive water when cleaning. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing. Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle. 008_051514 A certified electrician must furnish sufficient power for proper machine operation and install any supplied receptacle. We recommend this equipment be on a dedicated and protected circuit. Failure to wire properly will void the warranty and may result in damage to the machine. It is Gold Medal Products Co.'s recommendation that this machine be plugged directly into a wall outlet. The use of extension cords is not recommended due to safety concerns, and may cause sacrificed and/or reduced performance. Make sure cord is located to prevent a trip hazard or unit upset. Before You Plug In Machine 1. Make sure all machine switches are OFF before plugging equipment into receptacle. 2. Make sure wall outlet can accept the grounded plugs (where applicable) on the power supply cord. 3. The wall outlet must have the proper polarity. If in doubt, have a competent electrician inspect the outlet and correct if necessary. 4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable). 5. Install unit in a level position. CAUTION If the supply cord is damaged, it must be replaced by Gold Medal Products Co., its service agent or similarly qualified persons in order to avoid a hazard. 039_080614 Page 7 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 OPERATING INSTRUCTIONS Controls and Their Functions (3052 Auto Breeze) POWER SWITCH Two position, ON/OFF lighted rocker switch - supplies power to the Candy Switch. The green switch light ON indicates there is power to the unit. Immediate Power Off: To bypass the cooling cycle and immediately remove power from the machine, turn the Power Switch OFF. CANDY SWITCH Two position, "White" rocker switch - turns the motor and heating element ON/OFF. When turned OFF, the cooling cycle will start. After one (1) minute the cooling cycle completes, and the spinner head will stop rotating. Cooling is necessary to keep carbon from forming in the spinner head. AUTO COOLING INDICATOR LIGHT When lit, this amber light indicates the unit is in the cooling cycle. During the cooling cycle the spinner head will remain spinning. If the Auto Cooling Light is blinking during machine operation, it indicates there is a low voltage supply to the machine (less than 105 VAC). The machine may not operate properly (see Troubleshooting section of this manual). Power Switch Auto Cooling Indicator Light Candy Switch Page 8 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 Sugar for Your Candy Ready to Use Flossugar Our ready to use Flossugar is the preferred sugar for your new cotton candy machine; however 100% pure cane or beet sugar will do just fine. Our Flossugar gives you good rich colors, and great flavors, too. It is packed in handy half-gallon sealed cartons, with an E-Z pour spout for filling your machine. Flossugar comes in many flavors, and you can easily change flavors for greatest variety, and best sales. Mix Your Own If you want to mix your own, use our Flossine®, and please follow our directions. If you want a deeper color, slightly dampen the mixed sugar. Use a tablespoon of water per five pounds of sugar, sprinkle water over sugar, and mix well. DO NOT USE EXCESS COLOR! Too much color will ruin the element on your machine and could create a bitter taste to the candy. There is a limit as to how dark you can make cotton candy. That's because cotton candy is 98% air, and we cannot color the air. Sugar Considerations Today 99% of the sugar manufactured is extra fine granulated, which does have some small particles which can slip thru the ribbons without being melted. If this becomes objectionable, you can seek out medium coarse or sanding sugars. The larger crystal size will require a little more heat to melt. Read the label on the bag of sugar, today we see some free flowing sugars for restaurants. Free flowing sugars contain cornstarch which will burn onto your element/band clogging them rapidly. We have also seen some off-brand sugars that are a blend of sugar and dextrose or corn syrup. This product makes very poor cotton candy. Please make sure you get good sugar for your cotton candy machine. Page 9 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 Machine Operation Floss Machine Operation (3052 Auto Breeze) WARNING Floss head rotates at high speeds. Operator MUST keep hands and face clear of the floss head to avoid injury. Operator must wear eye protection. Keep all spectators at a reasonable distance, and use a Floss Bubble for added customer protection. 015_062714 1. Follow the guidelines described in the Electrical Requirements Section for supplying power to machine. 2. With the Candy Switch OFF, turn the Power Switch ON. The spinner head will not start to rotate. 3. With the spinner head stopped, pour flossugar into the spinner head. Always fill it 90% full with sugar. This 90% level is necessary to obtain a balanced condition in the floss head. DO NOT OVERFILL! IMPORTANT: NEVER add sugar when motor is running. 4. Turn the Candy Switch ON. The spinner head will rotate and heat. After about 30 seconds the machine will start to make cotton candy. 5. When the spinner head needs to be refilled with sugar, or to stop making cotton candy, turn the Candy Switch OFF. The cooling cycle will start. After 1 minute the cooling cycle completes, and the spinner head will stop rotating. When the spinner head is stopped, refill with flossugar. Turn the Candy Switch ON, and continue to make cotton candy. Note: During the cooling cycle the spinner head will remain spinning. Cooling is necessary to keep carbon from forming in the spinner head. DO NOT use the Power Switch for normal operation of the machine. This will bypass the cooling cycle. IMPORTANT: Failure to cool down the floss head could result in leaving melted sugar in the floss head. If the motor is restarted, this melted sugar will exit the floss head and could cause burns. In addition, sugar left in the floss head may smoke or cause carbon build up. Immediate Power Off: To bypass the cooling cycle and immediately remove power from the machine, turn the Power Switch OFF. When completing operation for the day (or any prolonged period), follow the instructions in the Shutdown Procedure/Cleaning and Care section of this manual. Page 10 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 Making Floss Pick a cone, if it sticks in the stack of cones, twist it off the stack. CAUTION Keep hands away from spinning head! 031_021914 Hold an inch or two of the pointed end of a cone between two fingers and a thumb. With a light flicking action, roll cone in the web of floss building up in the pan. Lift the cone up with the ring of floss attached and rotate the cone to wrap the floss. DO NOT roll floss while the cone is inside the pan. This will pack the floss too tightly. See steps 1 thru 8 shown below. If the floss fails to stick to the cone, pass the cone near the spinner head to pick up a "starter" of melted sugar. Lift the cone out of the pan and wrap the floss with a "figure eight" movement of the hand. This leaves giant pockets and makes the final product appear larger. Make sure room humidity is not too high, or product will be "heavy". 1. Grip cone as shown. 2. Break into web of floss with the cone. 3. Wind the sugar onto the cone. 4. Lift web of floss from the pan and roll onto the cone. 5. 6. 7. 8. WARNING · DO NOT PUT HANDS OR OBJECTS IN ROTATING SPINNER HEAD. · DO NOT FILL SPINNER HEAD WITH SUGAR WHILE IT IS ROTATING. · WEAR EYE PROTECTION. · DO NOT PUT HANDS NEAR ROTATING SPINNER HEAD. · USE FLOSS CONE TO COLLECT COTTON CANDY. 032_021914 Page 11 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 Rubber Float Adjustment In operation, the floss will collect on the FLOSS STABILIZER. If the floss collects "low" on the stabilizer, twist the front (leading) edge of the rubber floats down (as shown below). This creates a lifting action to float the floss higher on the wall of the floss pan. Be sure the rubber floats are fully inserted in the float holders on the Quick Release Floss Cap (see image below). Leading Edge of Rubber Float seen twisted down. Quick Release Floss Cap Rotation Leading Edge of Rubber Float seen twisted down. Rubber Float Adjustment Rubber Float shown fully inserted in float holders on the Quick release Floss Cap with leading edge twisted down. Page 12 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 Shut Down Procedure/ Care and Cleaning Shut Down Procedure (3052 Auto Breeze) 1. When completing operation for the day (or any prolonged period), run the floss head completely empty of sugar. 2. Turn the Candy Switch OFF. The cooling cycle will start. When the cooling cycle completes, the spinner head will stop rotating. 3. When the spinner head is stopped, turn the Power Switch OFF. 4. NEVER put water in the floss head. Care and Cleaning DANGER Machine must be properly grounded to prevent electrical shock to personnel. DO NOT immerse in water. DO NOT clean appliance with a water jet. Always unplug the equipment before cleaning or servicing. 025_111616 WARNING Burn Hazard. DO NOT touch spinner head. Allow to cool before cleaning or servicing. Avoid contact with molten sugar. 006_092414 Good sanitation practice demands that all food preparation equipment be cleaned regularly (only use non-toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of advertising your product. Follow the directions below to clean and sanitize the unit each day after use. 1. Unplug the machine and wait for the floss head to cool down to room temperature. 2. Make sure to clean all pans/accessories in order to sanitize them before each use. 3. Wipe all surfaces with a clean, damp cloth. 4. Wipe the stainless steel parts with a clean cloth and cleaner designed for stainless steel, such as Gold Medal Watchdog Stainless Cleaner (Item No. 2088). DO NOT use oven cleaners or abrasive materials as they will damage parts of the machine. Page 13 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 Floss Band and Element Disassembly and Removal of Floss Band 1. Unplug the machine from the power source and allow floss head to cool completely. 2. Remove all sugar from the head of the machine before disassembling. If needed, carefully turn the machine on its side and shake the sugar out. 3. Rotate the Quick Release Floss Cap clockwise to unlock, then lift cap off of the floss head retaining bolts (see image below). 4. Remove the Take-Apart Spinner Cap. 5. Unscrew the ball knob counterclockwise and remove. This knob secures the terminal lock. 6. Lift off the terminal lock which fastens the element lead wires. 7. Lift the two (2) element lead wires off the power studs, then the band and element can be removed from the spinner head. 8. If there is excessive sugar build-up, run hot water over band and element until the sugar dissolves (be careful to keep element leads dry). When the sugar has been removed, allow the band and element to air dry overnight. Note: For models with separate heat and motor switches, the best way to dry the floss head after reassembly is to spin it dry for 10 minutes WITHOUT HEAT (use motor switch only). Quick Release Floss Cap (Rotate clockwise to remove) Take-Apart Spinner Cap Floss Head Retaining Bolts Ball Knob Terminal Lock Rubber Float Take-Apart Floss Head Floss Band and Element Element Lead Wire shown on Power Stud Tubular Element View Page 14 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 Reassembly of Floss Band and Element 1. When reassembling, the floss band and element must be properly seated on the spinner head groove provided for the Quick Release Floss Cap to correctly and easily lock into place. The band is marked to show correct orientation for installation (see image below). 2. Reattach the (2) element lead wires to the (2) power studs, and secure with the terminal lock and ball knob. 3. Slide the Take-Apart Spinner Cap onto the retaining bolts. 4. Place the Quick Release Floss Cap over the spinner cap and make sure it is fully rotated counterclockwise into the locking position. 5. Check the rubber floats to make sure they are fully inserted in the float holders on the Quick Release Floss Cap. Band is marked to show correct orientation. Floss Band Orientation Band and Element must be properly seated on spinner head groove provided. Reassembling the Band and Element Page 15 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Issue Low Production Excessive Smoke Excessive Vibration Model No. 3052-00-001 Troubleshooting Possible Cause A. Excessive carbon on the element. B. Low line voltage. C. Foreign objects in the spinner head. A. Bypassing the cooling cycle. B. Product mixture. C. Excessive sugar buildup. A. Packing material not removed. B. Lock-N-Go Handles not in operating position. C. Low on sugar. Solution A. Follow the instructions for removing and cleaning band and element (see Floss Band and Element section). B. If the Auto Cooling Light is blinking during machine operation, it indicates there is low wall line voltage to the machine (less than 105 VAC). A primary reason for low production and poor equipment performance is low line voltage. Have a qualified electrician check the wall line voltage (where the machine is plugged in), and add new lines for all the various equipment plugged into the electric circuit if there is not enough current for the requirement listed on the equipment nameplate. The use of extension cords is not recommended due to safety concerns, and may cause sacrificed and/or reduced performance. If the use of an extension cord cannot be avoided then be sure it is no longer than 10 to 12 ft., and is at least 14 AWG wire. C. Foreign objects in the head assembly can short out an element or cause an out-of-balance condition. A. Bypassing the cooling cycle will cause excessive smoke and melting sugar. This can cause carbon buildup. See Floss Band and Element section of this manual for cleaning the band and element. B. Check the product mixture being used. For best results, use nothing with a cornstarch base. C. Check the band for excessive sugar buildup and remove if needed as described in the Floss Band and Element section of this manual. A. If the equipment is new, check that all packing materials were removed from the machine. B. Verify that the Lock-N-Go Handles have been rotated into the operating position. C. Refill the floss head; this will normally eliminate excessive vibration. When adding sugar to the floss head, always fill it 90% full to obtain a balanced condition in the head and eliminate vibration. Do not add sugar with the motor running! Page 16 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 Issue Possible Cause D. Foreign objects or sugar lumps. E. Stretched or uneven suspension springs. Lock-N-Go Handles are Hard to Rotate A. Clamping Cam friction. Quick Release Floss Cap is A. Hard to twist OFF Hard to Rotate (sugar build up) B. Hard to twist ON (band/element position) Solution D. Run the sugar completely out, then check for foreign objects or sugar lumps in the head assembly. E. If the suspension springs are stretched or uneven this can cause unwanted vibrations. Have Qualified Service Personnel replace if needed. A. If handles are hard to move, Qualified Service Personnel may need to apply Petro Gel (Gold Medal Item No. 1110), or a food safe lubricant, to the top surface of the Clamping Cam to reduce friction where the cam contacts the bell housing. A. If Quick Release Floss Cap is hard to twist off, clean any sugar build up before reinstalling. B. If cap is hard to twist on, check that the band and element are properly seated in spinner head groove provided (see Reassembly of Floss Band and Element). Page 17 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 MAINTENANCE INSTRUCTIONS DANGER Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death. DO NOT immerse any part of this equipment in water. DO NOT use excessive water when cleaning. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing. Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle. 008_051514 DANGER Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Any alterations to this equipment will void the warranty and may cause a dangerous condition. This appliance is not intended to be operated by means of an external timer or separate remote-control system. NEVER make alterations to this equipment. Read the Installation, Operating, and Maintenance Instructions thoroughly before installing, servicing, or operating this equipment. 014_020416 WARNING No user serviceable parts inside. Refer servicing to qualified service personnel. 011_051514 CAUTION THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE OPERATOR. 027_010914 Page 18 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 How to Check a Triac Triac - Top View 1. Set the Multimeter for ohms or continuity. 2. Disconnect all machine leads from the Triac. 3. Connect the positive ohmmeter lead to MT2 and the negative lead to MT1. The ohmmeter should indicate no continuity (OL) through the Triac. 4. Using a separate jumper lead, connect the gate of the Triac to MT2. The ohmmeter should indicate continuity (less than 100 ohms). 5. Reconnect the Triac so MT1 is connected to the positive ohmmeter lead and the negative lead to MT2. The ohmmeter should indicate no continuity (OL) through the Triac. 6. Using a separate jumper lead, connect the gate of the Triac to MT2. The ohmmeter should indicate continuity (less than 100 ohms). Page 19 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 ORDERING SPARE PARTS 1. Identify the needed part by checking it against the photos, illustrations, and/or parts list. (General images may be used in manual for reference only.) 2. Use only approved replacement parts when servicing this unit. 3. When ordering, please include part number, part name, and quantity needed. 4. Please include your model number, serial number, and date of manufacture (located on the machine nameplate/data plate) with your order. 5. Address all parts orders to: Parts Department Gold Medal Products Co. 10700 Medallion Drive Cincinnati, Ohio 45241-4807 Or, place orders by phone or online: Phone: (800) 543-0862 (513) 769-7676 Fax: (800) 542-1496 (513) 769-8500 E-mail: info@gmpopcorn.com Web Page: gmpopcorn.com Page 20 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 Cabinet Exterior and Lock-N-Go Handle Assembly 1 2 5 3 7 6 4 8 9 10 11 31, 32 29, 30 27, 28 26 25 24 12, 13 15 14 16 23* *CAUTION: If supply cord is damaged, it must be replaced by Gold Medal Products Co., its service agent, or similarly qualified persons in order to avoid a hazard. 22 21 20 19 18 Page 21 https://manual-hub.com/ 17 gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 Cabinet Exterior and Lock-N-Go Handle Assembly Parts List Item Part Description SPINNER HEAD, TUBULAR 5IN HEAD (Complete 1 Assembly) See Spinner Head Assembly section for individual parts breakdown. BRUSH HOLDER ASSY (includes Brushes, Caps 2 and Holders) See Brush Assembly Breakdown section for individual parts breakdown. 3 BELL HOUSING, DUAL BRUSH 4 LABEL,FLOSS ADVERTISEMENT 5 BOWL, SEAL RETAINER 6 BELL HOUSING SEAL 7 THREADED BUMPER,1/4-20 8 NAME,INSTRUCTION OVERLAY 9 SWITCH, LIGHTED ROCKER GR 10 PILOT LIGHT, AMBER 125V 11 SWITCH, ROCKER DPDT 12 10-24 X 1/2 PH TRUSS M/S 13 HEX NUT #10-24 ESLOK 14 RUBBER FOOT 3/4IN HIGH 15 HANDLE UNLOCK DECAL 16 LOCK N GO HANDLE, NEW CAB. 17 5/16-18 X 1/2 PH TR M/S 18 WASHER SS .5 ID X 1.10 OD 19 CLAMPING SHAFT, LOCK N GO 20 CLAMPING CAM 21 5/16 FLAT WASHER ZINC PLT 22 HEX NUT 5/16-18 ESLOK 23* POWER SUPPLY CORD 24 STRAIN RELIEF SR-6P3-4 25 WARNING LABEL CORD 26 8-32 X 3/8 PHIL PAN HEAD 27 1/4-20 X 3/4 GRADE 5 BOLT (w/Lock Washer) 28 TINNERMAN NUT 1/4-20 29 8-32 X 3/8 SLT. HWH M/S 30 #8-32 TINNERMAN FASTENER 31 INSPECTION BRUSH COVER 32 LABEL,CLEAN EVERY 500 LBS Part Number 3052-00-001 55139C 42382W 42190 42159 56561 56571 102017 102028 42798 55039 48615 42826 74691 47155 102253 56563 12183 48428 56565 42460 74134 12001 22038 76026 68720 87515 74520 42125 42044 47299 42381 42002 Page 22 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 5" Take Apart Spinner Head (Model No. 55139C) 1 2 3 Spinner Head Complete (Model 55139C) 6 4 5 7 14 15 16 17 18 19 8, 9 8 10 11 12 13 Floss Head Band Interior View 20 21 22 23* *Uses two Set Screws 24 Spinner Head Bottom Page 23 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 5" Take Apart Spinner Head (Model No. 55139C) Parts List Item Part Description 1 MOLDED RUBBER FLOAT 2 QUICK RELEASE FLOSS CAP (includes 2 Molded Rubber Floats 3 TAKE-APART SPINNER CAP 4 BREEZE BAND ASSEMBLY (includes element) 5 FLOSSHEAD RETAINING BOLT 6 BLACK BALL KNOB 7 TERMINAL LOCK 8 FLOSS ELEMENT BRACKET 9 8-32 LOCKNUT, REVERSIBLE 10 #8 INTERNAL TOOTH L/W 410SS 11 COUNTER WEIGHT 12 .188ID FLATWASHER 13 8-32 X 5/16 PH PAN M/S SPINNER BOTTOM, TUBULAR (Complete bottom 14 assembly includes Terminal Lock, Ball Knob, and items listed below.) 15 UPPER SPINNER HEAD 16 1/4-20 x 3IN SET SCREW 17 1/4-20 SERRATED LOCK NUT 18 HEX NUT #10-32 BRASS 19 #10 INTERNAL TOOTH WASHER 20 SLIP RING STUD 21 SLIP RING MACHINED 22 LOWER SPINNER HEAD 1/2 23 SET SCREW 1/4-20 X 3/8 (2 required for the Lower Spinner Head) 24 BOTTOM PHENOLIC WASHER Part Number 55139C 56549 102039 43166C 48784 56550 102050 56551 55118 48767 12132 55006 77052 89247 42284T 42437 102038 46311 42301 12573 42127 42126HD 42281 74125 20054 Page 24 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 Bell Housing Interior Brush Assembly 1, 2 3 4 8 5, 6 9 7 10 Item Part Description 1 HEX NUT #10-24 ESLOK 2 .188ID FLATWASHER 3 MOTOR MTG PLATE 4 MOTOR, FLOSS MACHINE 5 6-32 X 1/2 PH PAN HD M/S 6 6-32 GRIP NUT ZINC PLATED 7 BRUSH HOLDER ASSEMBLY (includes Brushes, Caps and Holders) 8 DUAL BRUSH HOLDER W/LEADS 9 CARBON BRUSH 10 CAP, BRUSH HOLDER Part Number 3052-00-001 74691 77052 42119 48649 47516 47517 42382W 42436W 55007 42138 Page 25 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 Cabinet Interior Parts Breakdown 305 2- 00 -0 00 14 15 16 1 17 12, 13 11 9, 10 8, 6, 7 2 3 4 5 6, 7 General image shown for parts reference only. When reassembling the unit: · Be sure the Bell Housing is located UNDER the Clamping Brackets as shown here. · Be sure to keep wiring clear of the locking mechanism. Page 26 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 Cabinet Interior - Parts List Item Part Description 1 MOTOR, FLOSS MACHINE 2 SWITCH, ROCKER DPDT 3 PILOT LIGHT, AMBER 125V 4 SWITCH, LIGHTED ROCKER GR 5 AUTO WATT CONTROLLER 6 6-32 X 3/8 PHIL PAN M/S 7 WASHER #6 INTERNAL TOOTH 8 TRIAC, 35A 600V 9 HEAT SINK 10 10-32 X 1/2 TRUSS HEAD 11 TERMINAL BLOCK, 2 POS 12 8-32 X 3/4 PHIL PAN MS SS 13 HEX NUT #8-32 STAINLESS 14 ACORN NUT 1/4-20 15 SPRING, SUSPENSION MEDIUM 16 SCREW 1/4-20X3/8 PN HD PH 17 10-24 TINNERMAM FASTENER Part Number 3052-00-001 48649 48615 55039 42798 55447 39000 76188 55155 48673 12189 55620 39007 89129 49068 42524 42360 42221 Floss Pan and Whirlgrip Stabilizer 4 3 2 Whirgrip Stabilizer (includes Floss Stabilizer and Clips) 1 Item Part Description 1 FLOSS PAN, 0.080 ALUM 2 WHIRLGRIP STABILIZER (Includes Floss Stabilizer and Clips) 3 FLOSS STABILIZER (Web) 4 WHIRLGRIP CLIPS Part Number 3052-00-001 42040 3010 43032 77470 Page 27 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 Wiring Diagram Model No. 3052-00-001 Page 28 https://manual-hub.com/ gmpopcorn.com Auto Breeze EZ Kleen Head Model No. 3052-00-001 WARRANTY Gold Medal Products Co. warrants to the original purchaser each item of its manufacture to be free of defects in workmanship and material under normal use and service. Gold Medal Products Co.'s obligation under this warranty is limited solely to repairing or replacing parts, f.o.b. Cincinnati, Ohio, which in its judgment are defective in workmanship or material and which are returned, freight prepaid, to its Cincinnati, Ohio factory or other designated point. Except for "Perishable Parts" on specific machines, the above warranty applies for a period of two (2) years from the date of original sale to the original purchaser of equipment when recommended operating instructions and maintenance procedures have been followed. These are packed with the machine. Parts warranty is two (2) years, labor is six (6) months. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. In no event shall Gold Medal Products Co. be liable for special, incidental or consequential damages. No claim under this warranty will be honored if the equipment covered has been misused, neglected, damaged in transit, or has been tampered with or changed in any way. No claim under this warranty shall be honored in the event that components in the unit at the time of the claim were not supplied or approved by Gold Medal Products Co. This warranty is effective only when electrical items have been properly attached to city utility lines only at proper voltages. This warranty is not transferable without the written consent of Gold Medal Products Co. The term "Original Purchaser" as used in this warranty shall be deemed to mean that person, firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS CO., or their authorized distributor for the equipment. THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS CO. AT 1-800-543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR REPLACEMENT OF PARTS. NOTE: This equipment is manufactured and sold for commercial use only. 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA gmpopcorn.com Phone: (800) 543-0862 Fax: (800) 542-1496 (513) 769-7676 (513) 769-8500 © 2018 The text, descriptions, graphics, layout, and other material in this publication are the exclusive property of Gold Medal Products Co. and shall not be used, copied, reproduced, or published in any fashion, including website display, without its express written consent. Page 29 gmpopcorn.com https://manual-hub.com/