User Manual for levelone models including: FVT-2001, FVT-2002, FVT-2201, FVT-2202, FVT-2401, GVT-2000, GVT-2001, GVT-2002, GVT-2003, FVT Series Copper to Fiber Stand Alone Media Converter, FVT Series, FVT Series Stand Alone Media Converter, Copper to Fiber Stand Alone Media Converter, Stand Alone Media Converter, Stand Media Converter, Alone Media Converter, Media Converter, Converter
LevelOne GVT-2003
File Info : application/pdf, 14 Pages, 260.13KB
DocumentDocumentCopper to Fiber Stand-Alone Media Converter User Manual Model No. FVT-2001 Description 10/100BASE-TX to 100BASE-FX MMF SC Converter, 2km FVT-2002 FVT-2201 FVT-2202 10/100BASE-TX to 100BASE-FX MMF ST Converter, 2km 10/100BASE-TX to 100BASE-FX SMF SC Converter, 20km 10/100BASE-TX to 100BASE-FX SMF SC Converter, 20km FVT-2401 10/100BASE-TX to 100BASE-FX SMF SC Converter, 40km GVT-2000 GVT-2001 GVT-2002 GVT-2003 10/100/1000BASE-T to 1000BASE-X SFP Converter 10/100/1000BASE-T to 1000BASE-SX MMF SC Converter, 550m 10/100/1000BASE-T to 1000Base-SX/LX SMF SC Converter, 20km 10/100/1000BASE-T to 1000Base-SX/LX SMF ST Converter, 20km Ver. 1.03 Table of Contents 1. INTRODUCTION ................................................... 1 1.1. FEATURES .................................................. 1 2.1. FRONT PANEL ............................................ 3 2.2. REAR PANEL............................................... 4 2.3. LED INDICATORS ....................................... 5 2.4. DIP-SWITCH ................................................ 7 3. CABLING................................................................. 8 4. SPECIFICATION.................................................. 10 5. OPTIONAL SFP MODULES............................... 12 1. Introduction LevelOne media converters are Fast Ethernet 10/100Base-TX to 100Base-FX and 10/100/1000Base-T to 1000Base-SX/LX converters to provide the flexibility required in network integration. The TX port auto-sense connection speed, auto-negotiates half/full duplex modes and auto-selects MDIX media type. The fiber connectors come with multimode or singlemode, SC, ST or SFP connector to provide necessary connection interface and distance capabilities. LevelOne have designed 19" racks to organize media converters the smart way by providing a single power supply. With the Plug-and-play technology, the converter is easy to set-up and run. For simple, cost-effective network design, LevelOne converter series is the perfect solution to bridge the complex network infrastructure. 1.1. Features Fast Ethernet Module § Comply with IEEE 802.3, 802.3u and 802.3x standards. § Convert between UTP cabling and Fiber-optic cabling. § One RJ-45 connector, Auto-MDI/MDIX for UTP port. § Support 10/100 Mbps Auto-negotiation for UTP port. § Fiber cabling connectivity up to 40Km. § Store-and-forward switching to separate two collision domains. 1 § One fiber connector (SC/ ST) for 100Base-FX. § 2 DIP-switches to set the operation mode § Link- Lost-Forwarding function. Gigabit Ethernet Module § Comply with IEEE 802.3, 802.3u and 802.3x, IEEE 802.3ab 1000BaseT, 802.3z 1000Base SX/LX standards. § Convert between UTP cabling and Fiber-optic cabling. § One RJ-45 connector, Auto-MDI/MDIX for UTP port. § Support 10/100/1000 Mbps Auto-negotiation for UTP port § Fiber cabling connectivity up to 80Km. § Store-and-forward switching to separate two collision domains. § One fiber connector (SC / SFP) for 1000Base-SX/LX § DIP-switches to set the operation mode function. § Link- Lost-Forwarding function. 2 2. Hardware Description 2.1. Front Panel l FVT-2001 / FVT-2002 / FVT-2201 / FVT-2401 / FVT-2202 l GVT-2000 l GVT-2001 / GVT-2002 / GVT-2003 3 2 1 (1) RJ-45 Port (3) Fiber/SFP Connector (2) LED Indicators (4) DIP-Switch 3 2.2. Rear Panel 4 Model No. FVT-2001 FVT-2002 FVT-2201 FVT-2202 FVT-2401 GVT-2000 GVT-2001 GVT-2002 GVT-2003 Power Adapter DC 5V, 1A DC 5V, 1A DC 5V, 1A DC 5V, 1A DC 5V, 1A DC 5V, 2A DC 5V, 2A DC 5V, 2A DC 5V, 2A 4 2.3. LED Indicators Fast Ethernet Module LED Status Meaning PWR On Power on FX On 100Mbps Fiber Speed On 100Mbps UTP Speed TX OFF 10 Mbps UTP Speed FDX On Converter works in the full duplex mode OFF Converter works in the half duplex mode L/A UTP(right) Connection status display for fiber link. On "ON" indicates that Fiber link is in correct connection. Blinks Active status display of fiber link "Blink" indicates packet goes through FX end. L/A Fiber(left) Connection status display for electric link. On "ON" indicates that electric link is in correct connection. Blinks Active status display of fiber link "Blink" indicates packet goes through TX end 5 Gigabit Ethernet Module LED PWR 1000 100 FDX L/A UTP(right) L/A Fiber(left) Status Meaning On Power on On 1000Mbps UTP Speed On 100Mbps UTP Speed On Converter works in the full duplex mode Off Converter works in the half duplex mode Blinks Active status display of electrical interface link Blink" indicates packet goes through TP Blinks Active status display of fiber interface link "Blink" indicates packet goes through FX Note: The UTP port speed is 10Mbps when both 100 and 1000 LED indicators "OFF" 6 2.4. DIP-switch The DIP-switch is used to configure operation mode for LLF (Link Lost Forwarding) and Flow-Control function for UTP/Fiber port. The default value of DIP switch is OFF. Fast Ethernet Module/Gigabit Ethernet Module No Status Description ON LFP is Enable 1 OFF LFP is Disable ON Flow-Control function ENABLED 2 OFF Flow-Control function DISABLED Link Lost Forwarding: When LLF is enable, allow UTP link failures to be reported to the fiber side and also allow Fiber link failure to be reported to the UTP side. Therefore, A link loss forward feature is provided in both UTP and Fiber side. Flow Control Function : Flow control stops and resumes the transmission of network traffic between two connected peer nodes on a full-duplex Ethernet physical link. Controlling the flow by pausing and restarting it prevents buffers on the nodes from overflowing and dropping frames. Note: Please don't change the DIP-switch setting when UTP or fiber port is transmitting or receiving data. It may cause some data error. 7 3. Cabling Fast Ethernet Module § Twisted-pair segment can be use unshielded twisted pair (UTP) or shielded twisted pair (STP) cabling. The cable must comply with the IEEE 802.3u 100Base TX standard for Category 5. The cable between the converter and the link partner (switch, hub, workstation, etc.) must be less than 100 meters (328 ft.) long. § Fiber segment using multi-mode connector type must use 50 or 62.5/125 um multi-mode fiber cable. You can connect two devices up to a 2-kilometer (6,562 ft.) distance. § Fiber segment using single-mode connector type must use 8/125 or 9/125 um single-mode fiber cable. You can connect two devices in the distance of 40 Kilometers in full duplex operation. For half-duplex operation, the recommended maximum distance is 412 meters (1,352 ft.) Gigabit Ethernet Module § Using four twisted-pair, Category 5 cabling for RJ-45 port connection. The cable between the converter and the link partner (switch, hub, workstation, etc.) must be less than 100 meters (328 ft.) long. § Fiber segment using multi-mode connector type must use 50 or 62.5/125 um multi-mode fiber cable. You can connect two devices up to 550m distances. § Fiber segment using single-mode connector type must use 8/125 or 9/125 um single-mode fiber cable. You can connect two devices in the distance of 80 Kilometers in full duplex operation. For half-duplex operation, the recommended maximum distance is 412 meters (1,352 ft.) 8 Optical Fiber Module Name Wavelength 100Base-FX Fiber SC MM 100Base-FX Fiber ST MM 100Base-FX Fiber SC SM 20KM 100Base-FX Fiber SC SM 40KM 100Base-FX Fiber SC SM 20KM 1000Base-SX Fiber SC MM 1000Base-SX/LX Fiber SC SM 20KM 1000Base-SX/LX Fiber ST SM 20KM 1310 (nm) 1310 (nm) 1310 (nm) 1310 (nm) 1310/1550 (nm) 850 (nm) 1310 (nm) 1310 (nm) Avg. Launch Avg. Power Sensitivity >-21dBm -31dBm >-21dBm -31dBm >-15dBm -34dBm >-10dBm -37dBm >-10dBm >-10.5dBm >-8dBm -34dBm -20dBm -23dBm >-8dBm -23dBm Module Name 100Base-FX Fiber SC MM Avg. Power Loss Budget Max. FDX Fiber Distance 10 (dBm) 2 (Km) 100Base-FX Fiber ST MM 10 (dBm) 2 (Km) 100Base-FX Fiber SC SM 19 (dBm) 20(Km) 100Base-FX Fiber SC SM 100Base-FX Fiber SC SM1310/1550 (nm) 1000Base-SX Fiber SC MM 1000Base-SX/LX Fiber SC SM 1000Base-SX/LX Fiber ST SM 27 (dBm) 24 (dBm) 9.5 (dBm) 15 (dBm) 15 (dBm) 40(Km) 20(Km) 550 (m) 20(Km) 20(Km) Fiber Size (um) 62.5/125 50/125 62.5/125 50/125 9/125 8/125 9/125 8/125 9/125 8/125 62.5/125 50/125 9/125 9/125 9 4. Specification Fast Ethernet Module IEEE802.3 10BASE-T Standard IEEE802.3u 100BASE-TX/100BASE-FX IEEE802.3x Flow Control and Back pressure Fiber: Duplex ST/SC Connector RJ-45 Socket: CAT-3/5 (10/100Mbps) Twisted Pair cable, Auto MDI/MDI-X, Auto-Negotiation Switch architecture Store and Forward Fiber Core: Multi-Mode (62.5/125um, 50/125um) Single-Mode (8/125um, 9/125um) Fiber parameters Wavelength: 1310nm(Multi-mode) 1310nm(Single-mode) 1310/1550nm(Single-mode fiber) Fiber Distance: Multi-Mode Fiber 2KM Single-Mode Fiber (20KM or 40KM) Transparent packet 64 to 1600 Bytes for Non-VLAN Ethernet packet Link Fault Pass through UTP è Fiber: If UTP port link down, then converter will forced fiber to link down. Fiber è UTP: If Fiber port link down, the media converter will force UTP port to link down. DIP Switch DIP Switch 1: LFP function DIP Switch 2: Flow-Control function LED Power Power, UTP (100Mbps, L/A, FDX) Fiber (L/A, 100Mbps) DC5V, 1A Dimension 71mm x 94mm x 26mm EMI & safety CE, FCC Class A 10 Gigabit Ethernet Module IEEE802.3 10BASE-T IEEE802.3u 100BASE-TX Standard IEEE 802.3ab 1000BaseT IEEE 802.3z 1000BaseSX/LX standards IEEE802.3x Flow Control and Back pressure Fiber: SC / SFP Connector RJ-45 Socket: CAT-5 (10/100/1000 Mbps or pure 1000Mbps) Twisted Pair cable, Auto MDI/MDI-X, Auto-Negotiation Switch architecture Store and Forward Fiber Core: Multi-Mode (62.5/125um, 50/125um) Fiber Wavelength: 850nm(Multi-mode) parameters 1310nm(Single-mode) Fiber Distance: 550M (Multi-Mode Fiber) Transparent packet 64 to 9000 Bytes for Ethernet packet UTP è Fiber: If UTP port link down, then converter will forced Link Lost fiber to link down. Forward Fiber è UTP: If Fiber port link down, the media converter will force UTP port to link down. DIP Switch DIP Switch 1: LFP function DIP Switch 2: Flow-Control function LED Power, UTP (L/A, 100Mbps, 1000Mbps, FDX) Fiber (L/A) Power DC5V, 2A Dimension 71mm x 94mm x 26mm EMI & safety CE, FCC Class A 11 5. Optional SFP Modules CVH-2000 supports 3.3V mini-GBIC module Model No. GVT-0300 GVT-0301 Description 1.25Gbps Multi-mode SFP Transceiver, 550m, 850nm 1.25Gbps Single-mode SFP Transceiver, 10km, 1310nm 12macOS 版本12.6.3（版號21G419） Quartz PDFContext Word