Unified Communications Made Easy for Everyone - Zultys
User Guide for ZULTYS models including: Z23GE, 2APWA-Z23GE, 2APWAZ23GE, Z 23G, Gigabit Business IP Phone, Z 23G Gigabit Business IP Phone
Zultys, Inc. Z23GE Gigabit SIP IP Phone with BT 2APWA-Z23GE 2APWAZ23GE z23ge
File Info : application/pdf, 8 Pages, 1.07MB
DocumentDocumentGigabit Business IP Phone Z 23G Z 23G END CALL WWW.ZULTYS.COM Quick Start Guide PackagienCgoCnotnetnetns ts The following items are included in your package. If you find anything missing, contact your system administrator. Z 23G END CALL Handset Cord Ethernet Cable Stand IP Phone Handset Quick Start Guide Power Adapter Wall Mount Bracket (Optional) (Optional) Note: We recommend that you use the accessories provided or approved by ZULTYS. The use of unapproved third-party accessories may result in reduced performance or damage. Assembling the Phone 1. Attach the stand, as shown below: A B Desk Mount Method Note: The phone may also be wall mounted using the optional Z 23G wall mount bracket. Refer to wall mount installation guide for additional information. 2. Connect the handset and optional headset, as shown below: Headset Note: A compatible headset may be purchased separately. 2 Handset 3. Connect the network and power as shown below: The phone may be powered using the optional ZULTYS 5V DC power adapter or via Power over Ethernet (PoE). Your system administrator will advise which method to use. Optional USB Wi-Fi Adapter Power Adapter (DC 5V) Network PC (Optional) 4. Connecting to a wireless network: To connect to a wireless network using the optional ZULTYS Wi-Fi Adapter, perform the following steps: 1. Connect the optional ZULTYS 5V DC power adapter and allow the phone to reach the idle screen. 2. Plug the ZULTYS Wi-Fi Adapter into the USB port on the rear of the phone. 3. When the phone displays `WLAN adapter is added' press OK to scan for available networks. 4. Scroll down to `Available networks' and press Enter. 5. Select the network you wish to connect to then press the Link button. 6. Enter the password and press OK. A green tick icon indicates a successful connection. 5. Connecting a Bluetooth headset: To connect a compatible Bluetooth headset perform the following steps: 1. Select Menu > Basic > Bluetooth, set Bluetooth to Enabled and then press OK. 2. Place the Bluetooth headset into pairing mode then press Scan to locate the headset. 3. Select the headset from the list and then press Link to connect. Note: The IP phone should only be used with a ZULTYS 5V DC power adapter. The use of a third-party power adapter may cause damage to the phone. If you are connecting a PC to the Network port of the phone, it is recommended that you use the Ethernet cable provided with the phone. If inline power (PoE) is provided, you do not need to connect a power adapter. Make sure the switch is PoE-compliant per the IEEE 802.3af standard. Screen Icons In hands-free mode In headset mode In handset mode Mute activated Ringer off Call is on hold Auto-answering activated Call Forward activated Do not disturb activated (Red) Dialed call(s) Network Quality Indicator Keypad locked New Voicemail Messages Network connected Missed call(s) X Network disconnected Received call(s) ! No IP address VLAN activated Wireless network connected Wireless network disconnected Wireless network failure Bluetooth device paired 3 Basic Call Features Placing a Call Using the handset: 1. Pick up the handset. 2. Enter the number, and then press the Dial soft key or . --Alternatively-- Enter the number and then lift the handset to initiate the call. Using the speakerphone: 1. With the handset on-hook, enter the number. 2. Then press or the Dial soft key. Using the headset: 1. With the headset connected, press to activate the headset mode. 2. Enter the number, and then press the Dial soft key or . Note: During a call, you can alternate between the headset, hands-free speakerphone and handset modes by pressing the HEADSET key, the Speakerphone key or by picking up the handset. Answering a Call Using the handset: Pick up the handset. Using the speakerphone: Press or the Answer soft key. Using the headset: Press or the Answer soft key if headset mode is active. Note: Reject an incoming call by pressing the Reject soft key or silence the ringer by pressing the Mute key. Ending a Call Using the handset: Hang up the handset or press the -End Call key. Using the speakerphone: Press or press the -End Call key. Using the headset: Press the -End Call key. Redial Press to enter the Out Calls list, press or to select the desired entry, and then press or the Dial soft key. Press twice when the phone is idle to dial the last dialed number. Call Mute and Un-mute Press to mute the microphone during a call. Press again to un-mute the call. Call Hold and Resume To place a call on hold: Press the Hold soft key during an active call. To resume the call, do one of the following: If there is only one call on hold, press the Resume soft key. If there is more than one call on hold, press or to select the desired call, and then press the Resume soft key. 4 Call Transfer You can transfer a call in the following ways: Blind Transfer 1. Press the Trans soft key during an active call. The call is placed on hold. 2. Enter the number you want to transfer to. 3. Press the Trans soft key again to complete the transfer. Semi-Attended Transfer 1. Press the Trans soft key during an active call. The call is placed on hold. 2. Enter the number you want to transfer to, and then press . 3. Press the Trans soft key when you hear the ring-back tone. Attended Transfer 1. Press the Trans soft key during an active call. The call is placed on hold. 2. Enter the number you want to transfer to, and then press . 3. Press the Trans soft key when ready to complete the transfer or the End soft key to cancel transfer. Call Forward To enable call forward: 1. Press the Menu soft key when the phone is idle, and then select Features->Call Forward. 2. Select the SIP Line (usually #1) and then the desired forward type: Unconditional----Incoming calls are forwarded unconditionally. Busy Forward----Incoming calls are forwarded when the phone is busy. No Answer----Incoming calls are forwarded if not answered after a period of time. 3. Select `Enable' and enter the `Forward to' number. For No Answer Forward, enter the `Time' in seconds to wait before forwarding. 4. Press the OK soft or hard key to accept the change. Note: Advanced `Call Handling Rules' may be configured from the ZAC unified communications client app. Conference Call 1. Press the Conf soft key during an active call. The call is placed on hold. 2. Enter the number of the second party, and then press the Dial soft key or . 3. Press the Conf soft key again when the second party answers. All parties are now joined in the conference. 4. Press the End soft key to disconnect all parties. Note: You can split the conference call into two individual calls by pressing the Split soft key. Voice Message The Message waiting indicator on the idle screen will indicate when one or more voicemail messages are available and the Message Waiting Indicator LED at the top right of screen will flash red. To listen to voice messages: 1. Press key. 2. Follow the voice prompts to listen to your voice messages. 5 CuCstuosmtoimziinzgingYoYuoruPr hPhoonnee Call History 1. Press the key when the phone is idle to access the Call History, press or 2. After selecting an entry from the list, you can do the following: Press the Dial soft key to call the entry. Press the Delete soft key to delete the entry from the list. If you press the Option soft key, you can also do the following: Select Detail to view detailed information about the entry. Select Add to Contact to add the entry to the local directory. Select Add to Blacklist to add the entry to the blacklist. Select Delete All to delete all entries from the list. to select an entry. Contact Directory To add a contact: 1. Press the Contact soft key when the phone is idle, and then select All Contacts. 2. Press the Add soft key to add a contact. 3. Enter a unique contact name in the Name field and contact numbers in the corresponding fields. 4. Press the OK soft key to accept the change. To edit a contact: 1. Press the Contact soft key when the phone is idle, and then select All Contacts. 2. Press or to select the desired entry, press the Option soft key and then select Edit. 3. Edit the contact information. 4. Press the OK soft key to accept the change. To delete a contact: 1. Press the Contact soft key when the phone is idle, and then select All Contacts. 2. Press or to select the desired entry, press the Option soft key and then select Delete. 3. Press the OK soft key when the LCD screen prompts "Delete?". Note: Contacts may also be added from call history. For more information, refer to Call History above. Volume Adjustment Press Volume + or - key during a call to adjust the receiver volume of the handset/speakerphone/headset. Press Volume + or - key when the phone is idle or ringing to adjust the ringer volume. 6 My Details Name Extension DID ZAC Login Credentials Login Name (case sensitive) Password Host/URL Assigned Phone ID Support Contact Phone Email Notes 7 FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Radiation Exposure Statement: The equipment complies with FCC Radiation exposure limits set forth for uncontrolled enviroment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. ISED Canada Statement This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. Ce produit répond à la innovation, des sciences et de Développement économique Canada spécifications techniques applicables. About Zultys Zultys is the global provider of a true all-in-one unified communications solution. Innovative, reliable and scalable, Zultys IP phone systems integrate voice, video, data and mobility in a single premise based appliance or in the cloud - to optimize collaboration for businesses of all sizes. Zultys delivers a powerful, feature-rich communications system that is easy-to-use, deploy and maintain. Zultys is headquartered in Silicon Valley with offices around the world. WWW.ZULTYS.COM Zultys, Inc. 785 Lucerne Drive, Sunnyvale California, 94085, USA Copyright © 2021 Zultys, Inc. All rights reserved 96-35231- 01