Instruction Manual for delta models including: RS4000 Single Bike Wall Mount Rack, RS4000, Single Bike Wall Mount Rack, Bike Wall Mount Rack, Wall Mount Rack, Mount Rack
Delta Cycle Leonardo Bike Rack Garage Wall Mount Storage, Elegant Vertical Hanger Hook Design Provides Easy Bicycle Storage Access, Bike Wall Mount Rack Holds Any Bike Up to 40 lbs, Fat Tire Option : Home & Kitchen
Single Bike Wall Mount Rack Assembly instructions 1 Locate stud beneath wallboard and mark position of desired height to hang bike. 2 Use back plate to mark positions for drilling pilot holes for mounting screws. Drill holes. IMPORTANT SAFETY NOTE Beware of drilling into electrical wire or pipes within wall! Use spirit level to ensure plate is horizontal when drilling holes for mounting screws. (for Model RS4007 (with Tire Tray) 3 Hang bike on hook to determine lower plate height. 4 Position bottom plate in line with top plate, remove backing tape and adhere to wall. Tools Required Phillips Head Screwdriver Hand Drill 1/8" (3mm) Spirit Level Way of locating studs within the wall (see hardware store for advice) STUD CENTERLINE WALLBOARD STUD WARNING Do not exceed maximum total weight limit of 18kg/40lbs. Incorrect wall mounting could result in items falling and injury to persons. Avoid mounting in a position where personal injury could result from walking into protruding rack. Do not allow children to play or hang from Rack. Single Bike 5 131 Wall Mount Rack 280 9 193 28 125 3 Wall Elevation Dimension 36.5 OPTION A All bicycles hanging from front wheel (most common application) 35.448 OPTION B Alternate hanging of bicycles from front wheel to back wheel (for maximum number of bicycles on a wall) 34 cm (13 3/8") From Corner of Wall 12.35 cm (4 7/8") 64 cm (25 1/4") From Center to Center 46 cm (18 1/8") From Center to Center 34 cm (13 3/8") From Corner of Wall 12.35 cm (4 7/8") 181 cm (71 1/4") From Floor 181 cm (71 1/4") From Floor WARNING Do not exceed maximum total weight limit of 18kg/40lbs. Incorrect wall mounting could result in items falling and injury to persons. Avoid mounting in a position where personal injury could result from walking into protruding rack. Do not allow children to play or hang from Rack. Single Bike Wall Mount Rack with Tray for Fat Tires Assembly instructions RS4008C 1 Locate stud beneath wallboard and mark position of desired height to hang bike. 2 Use back plate to mark positions for drilling pilot holes for mounting screws. Drill holes. IMPORTANT SAFETY NOTE Beware of drilling into electrical wire or pipes within wall! Use spirit level to ensure plate is horizontal when drilling holes for mounting screws. 3 Hang bike on hook to determine lower plate height. 4 Position bottom plate in line with top plate, remove backing tape and adhere to wall. STUD CENTERLINE Tools Required Phillips Head Screwdriver Hand Drill 1/8" (3mm) Spirit Level Way of locating studs within the wall (see hardware store for advice) WALLBOARD STUD WARNING Do not exceed maximum total weight limit of 22.6kg/50lbs. Incorrect wall mounting could result in items falling and injury to persons. Avoid mounting in a position where personal injury could result from walking into protruding rack. Do not allow children to play or hang from Rack. Single Bike Hinge Wall Mount Rack STUD Assembly instructions RS4100 1 Locate stud beneath wallboard. 2 Position plate at desired height and screw into place. (screws should be in center of wall stud) IMPORTANT SAFETY NOTE Make sure the plate is level when mounting. 3 Place bike on hook to determine lower plate height. 4 Position bottom plate in line with top plate and screw in place. WALLBOARD Tools Required Phillips Head Screwdriver Hand Drill 1/8" (3mm) Spirit Level Way of locating studs within the wall (see hardware store for advice) STUD CENTERLINE WARNING Do not exceed maximum total weight limit of 18kg/40lbs. Incorrect wall mounting could result in items falling and injury to persons. Avoid mounting in a position where personal injury could result from walking into protruding rack. bike hanger Assembly instructions RS4200 1 Locate stud beneath wallboard. 2 Slide hook into base and lock into pin. 3 Position plate at desired height and screw into place. (screws should be in center of wall stud) IMPORTANT SAFETY NOTE Make sure hook is secured to base using locking pin, and that the plate is mounted level Tools Required Phillips Head Screwdriver Hand Drill 1/8"(3mm) Spirit Level Way of locating studs within the wall (see hardware store for advice) Assembly video Visit designbydelta.com/downloads STUD STUD CENTERLINE WALLBOARD 101022 WARNING Do not exceed maximum total weight limit of 18kg/40lbs. Incorrect wall mounting could result in items falling and injury to persons. Avoid mounting in a position where personal injury could result from walking into protruding rack.Adobe Illustrator 24.0 (Macintosh) Adobe PDF library 15.00