FLYWOO
impulserc.blob.core.windows.net/utilities/ImpulseRC_Driver_Fixer.exe
Instruction Manual for Flywoo models including: 68E-9804-PNP Firefly Hex Nano Hexacopter, 68E-9804-PNP, Firefly Hex Nano Hexacopter
FLYWOO Help Center | Firefly hex nano Series
File Info : application/pdf, 11 Pages, 5.09MB
DocumentDocumentFLYWOO Firefly hex nano VISTA HD V1.0 Firefly hex nano Manual VISTA HD BF Version 1/ drone introduction FLYWOO Firefly hex nano VISTA HD V1.0 In an effort to push the boundaries of carry the camera on the smallest platform, Flywoo designed the smallest hexacopter possible in their history. Firefly Hex nano , a nano- sized fpv drone designed to carry Insta 360go SMO 4K camera for some action flying. Weighing in at just 57.9g , the Firefly hex nano is small , flexible, stable , but is full of power and offers unmatched control . Pilots can quietly enjoy the fun of shooting a video without jelly. The Hex nao is equipped with GOKU HEX 13A STACK and 6pcs ROBO 1202.5 5500KV motors, to bring the Firefly a quiet, stable, flexible and long flight time characteristics. Perfect for the indoor and outdoor recording every beautiful flying moment! Battery recommend Flight time: About 6 min flight with Explorer 450mAh 4S battery About 4 min flight with Explorer 300mAh 4S battery FLYWOO Firefly hex nano VISTA HD V1.0 2/ Configuration and wiring diagram description Specifications Item: Firefly hex nano hexacopter Weight: 57.9g (without battery) Wheelbase: 90mm FC & ESC : GOKU HEX F745HEX 16*16 STACK - ( FC+13A ESC ) Frame: Firefly hex nano Frame Motors: Robo 1202.5 5500KV Props: HQ 40mm 4-Blades Props Receiver Option: Frsky XM+ / TBS Crossfire Camera Degree: 15°-90° VTX: Goku VTX625 450mw Antenna: Atomic 5.8GHz Antenna Length 30mm (LHCP) Battery: 4S 450mAh / 4S 300mAh battery (Not including) Equipped with GOKU HEX F745 16X16 NANO STACK, and NIN 1404 v2-2750kv, support 4s battery. Use powerful F745 BGA chipbarometer, black box, WS2812LED support 7 complete hardware serial ports, I2C and other functions are all open ! Enough to meet all FPV needs. FLYWOO Firefly hex nano VISTA HD V1.0 Target firmwareFLYWOOF745HEX UART1: TBS/R9M/XM+/DSMX/SBUS receiver UART2: NULL UART3: VISTA OSD TX/RX UART4: VISTA SBUS RX (Only use DJI remote control to turn on, and turn off RX1) UART5: NULL UART6: NULL UART7: NULL 3/ Receiver binding FLYWOO Firefly hex nano VISTA HD V1.0 TBS NANO 915: When the USB is connected, the green light of the receiver flashes, and then bind according to the picture operation. https://www.youtube.com/watch?v=-iNkVcOLITM&ab_channel=Danimal3D R9MM FCC ACCESS OTA Make sure your remote control supports ACCESS protocol, then follow the link to register and bind https://www.youtube.com/watch?v=az5hDdNBcjg&t=9s&ab_channel=FrSkyRC If the remote control is ACCST protocol, please bind as follows: 1/ Put these two files into the firmware directory of the SD card of the remote control. R9MM firmware: FW-R9MM-ACCST_v20190201 R9M TX module: FW-R9M-ACCST-20190117 2/ Insert the R9M TX module and write the firmware you need FLYWOO Firefly hex nano VISTA HD V1.0 3/ To write the firmware of the R9MM receiver, you need to remove the R9MM receiver, and then write the firmware by connecting to the S.PORT port. 4/ After both R9M TX and R9MM RX are written into the ACCST firmware. Binding method: 1/ Press and hold the button of RX, power on, the red and green lights are always on. 2/ Then after R9MM selects binding, RX red light flashes, and then exit 3/ RX is powered on again, and only a green light is displayed, indicating that the binding is successful. XM+ receiver: 1/ Press the XM+ receiver button, USB power supply, the red and green lights are always on 2/ The remote control turns on the binding mode, the green light flashes to indicate successful binding, turn off and restart FLYWOO Firefly hex nano VISTA HD V1.0 3-1/ Then set the corresponding serial port and receiver protocol to ensure the normal output of each channel of the receiver. 4/ Mode setting: Set the ARM switch and flight mode switch, AUX* corresponds to the remote control switch, and the yellow area mark is turned on. 5/ Motor test: FLYWOO Firefly hex nano VISTA HD V1.0 Unload the propeller, test the rotation direction of the motor, turn on the safety switch, and test the rotation of the motors one by one. FLYWOO Firefly hex nano VISTA HD V1.0 6/ Flight firmware upgrade and write default CLI 1/ Activate DFU mode 2/ BF Configurator will display to enter DFU mode. If it does not enter DFU mode, it may be that the driver is not installed. The driver can be installed using IMPULSE RC software Driver software: https://impulserc.blob.core.windows.net/utilities/ImpulseRC_Driver_Fixer.exe 3/ Then load the local HEX firmware and wait for the flashing to complete. A green progress bar is displayed to indicate completion, and DFU will become a COM port FLYWOO Firefly hex nano VISTA HD V1.0 4/ After the connection is entered, it is a blank interface, you need to write CLI commands, Factory CLI LINK: https://flywoo.net/pages/manual 5/ If the command is not restarted after writing the command, please write SAVE and press Enter to save, and the FC will restart FLYWOO Firefly hex nano VISTA HD V1.0 6/ Then all functions of FC return to normal.