Marshall Electronics - Professional Broadcast Miniature/Compact/Indoor 4K/UHD/HD Cameras, 4K Rack Mount/Desktop Monitors, Hardware, and Accessories.
User Guide for Marshall models including: CV350-10XB, Compact 10X Autofocus Camera Full-HD, CV350-10XB Compact 10X Autofocus Camera Full-HD, 10X Autofocus Camera Full-HD, Autofocus Camera Full-HD, Camera Full-HD
מצלמת HD זום X10 קומפקטית Marshall CV355-10X HDMI/3GSDI מבית ABS יבואנית מותגי צילום
File Info : application/pdf, 2 Pages, 238.11KB
DocumentDocumentCV350-10XB/10X Quick Start Guide Compact 10X Autofocus Camera (Full-HD) CV350-10X: 1080P25/30, 1080i50/60, 720P50/60, 1080P50/60 CV350-10XB: 1080P29.97, 1080i59.94, 1080P59.94, 720P59.94 Hardware Overview Front Hole for wall or ceiling mount 10x Auto Focus Lens ! WARNING CAUTION CAUTION Precautions Do not use the camera if fumes, smoke or a strange odor is emitted from the unit, or if it seems to not function correctly. Disconnect the power source immediately and consult your supplier. Always follow the instructions in the installation guide when applying power. Fire and equipment damage can occur if power is applied incorrectly. For the correct power supply, refer to the Do not install or operate in small, unventilated areas. Heat build up CAUTION To prevent damage, do not drop the camera or subject it to strong shock or vibration. CAUTION If installed close to a TV, radio transmitter, magnet, electric motor interfere with or distort the image. CAUTION Whether or not the camera is used outdoors, never point it toward the sun. Use caution when operating the camera in the vicinity of spot CAUTION Do not use the camera in extreme environments where high temperatures or high humidity exists. Use the camera under conditions where temperatures are between 14°F ~ 122°F (-10°C ~ 50°C), and humidity is below 90%. Regulatory Notice This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Features · 1/3" Progressive 2.1 Megapixel CMOS · 10x Optical Zoom, F=4.7mm ~ 47mm, F1.6 ~ F3.0 · 3G/HD-SDI(BNC), HDMI · 0.2Lux (Color), 0.1Lux (B/W), 0.005Lux (DSS On) · Optical Multi Coated ICR Filter · 3D-DNR, Privacy Masking · Defog, HLC, WDR, DIS, NegArt, Freeze, B&W · Full OSD control · 12VDC Remote Control IR Receiver Rear Z/F & Menu Controls Key Remote Control IR Receiver Power LED 1. PWR + 2. PWR 3. RS485 + 4. RS485 - 1 234 3G/HD-SDI 3G/HD-SDI Output 1. POWER + 2. POWER 3. RS-485 + 4. RS-485 - HDMI HDMI Video Output Zoom, Focus & Menu Controls MENU On, One Push AF Key Menu On: Press and hold menu key for 2seconds to display menu. Menu Mode: To select data or exit from menu, press menu key. One Push AF: To adjust focus position, press and release menu key when One Push AF mode is enabled. Focus NEAR: Press and hold right key for continuous optical focus near. MENU: To change menu parameter, press right key while menu is displayed. Focus Far: Press and hold left key for continuous optical focus far. MENU: To change menu parameter, press left key while menu is displayed. Zoom TELE: Press and hold up key for continuous optical zoom in(Tele). MENU: To move up menu item, press up key while menu is displayed. Zoom WIDE: Press and hold down key for continuous optical zoom out(Wide). MENU: To move down menu item, press down key while menu is displayed. Marshall Electronics LCDracks.com Specifications Image Sensor Scanning System Sensor Sync. System Effective Pixel Min. Illumination Horizontal Resolution Lens Optics Zoom Focus Angle of View(H) Back Light Compensation Exposure Functions White Balance Day & Night System Electronic Shutter Functions SDI Output Video Output CVBS (NTSC/ PAL) HD Output Control RS485 Interface D/N input Operation Temperature Power Input General Power consumption Dimensions (D x W x H) 1/3" Progressive CMOS (Approx. 2.1 mega) 16:9 Progressive Internal 1920(H) x 1080(V) 0.2Lux (Day), 0.1Lux (Night), 0.005Lux(DSS on) 1000TVL 10x Optical Zoom, F=4.7~47mm, F1.6 ~ F3.0 10x optical zoom x 12x digital zoom = 60x Near/Far, Auto/Manual/One Push 57.7 degrees(WIDE), 6.4 degrees(TELE) WDR/BLC, HLC(High Light compensation) Auto / Manual Auto(3,000°K~8,000°K) / ATW(1,900°K~11,000°K) / Manual AGC / TDN(ICR) NTSC: 1/30~1/30000, PAL: 1/25~1/30000, DSS( ~ 1/1sec) Privacy Mask, Image Mirror, 3DNR, Flicker-less, Sharpness, Defog, DIS, NegArt, Freeze, B&W SMPTE 292M(1.485Gbps): 1080P@29.97, 1080i@59.94, 720P@59.94 SMPTE 424M (2.97Gbps): 1080P@59.94 800mVp-p, 75, unbalanced generator(single-ended) HDMI 1920x1080p@59.94, 1920x1080i@59.94, 1920x1080p@29.97, 1280x720p@59.94 PELCO-P/D, SONY-VISCA protocol 8bits data, 1 stop bit, no parity, 2400~115200bps OPEN(floating): Day mode, CLOSE: Night mode -20 ~ 60 12VDC (7V to 15VDC) Max 6W (4.8W Lens inactive, 5.5W Lens active) 95.0 x 60.5 x 58mm (3.74 x 2.38 x 2.28") Dimensions 93.7mm 95.0mm 1. PWR + 2. PWR - 4. RS485 - 1 234 3G/HD-SDI HDMI 60.5mm 58mm Design and specifications are subject to change without notice. CV350-10XB/10X Setup Menu LCDracks.com SETUP WB CONTROL AE CONTROL (EXPOSURE) FOCUS CONTROL BACK LIGHT IMAGE CONTROL DISPLAY CONTROL RESET EXIT SUB MENU AWB ATW PUSH INDOOR OUTDOOR MANUAL INDOOR, OUTDOOR BRIGHTNESS IRIS AGC LIMIT SHUTTER DSS(SENS-UP) FLICKERLESS FOCUS MODE ZOOM SPEED TELE LIMIT WIDE LIMIT FAR END NEAR END LENS INITIAL USER PRESET WDR/BLC ACE ECLIPSE AUTO DAY NIGHT EXT COLOR LEVEL SHARPNESS IMAGE FLIP DEFOG 3D-DNR MOTION SHADING GAMMA RESOLUTION USER TITLE ZOOM MAGNIFICATION PRIVACY ADDRESS ADDRESS DISPLAY BAUDRATE LANGUAGE DEFECT ADJ VER. SUB MENU BLUE, RED AUTO MANUAL SHUTTER PRIORITY IRIS PRIORITY BRIGHT MANUAL, 0~20 AUTO, MANUAL, 0~17 0~20 AUTO, MANUAL, 1/2~40K MANUAL, OFF~1/1 OFF, ON AUTO MANUAL PUSH 0~7 X3~X120 X1~X8 INFINITY, 2, 3, 5, 10M 30CM, 1, 1.5, 2, 3, 5, 10M OFF, AUTO, ONE PUSH WDR BLC SPOT GAIN LEVEL COLOR D/N LEVEL MARGIN DWELL TIME NIGHT BURST NIGHT BURST D/N LEVEL DWELL TIME NIGHT BURST 0~20 0~20 AUTO, MANUAL OFF, LOW, MIDDLE, HIGH 01~255 OFF, ON DESCRIPTION Controls the automac adjustment of the light source's color temperature to 3,000°K ~ 8,000°K. Connuously adjusts camera color balance in accordance with any change in color temperature. Compensates for color temperature changes within the range of Color temperature will be manually adjusted by pushing the OSD buon. Place the white paper in front of the camera when OSD buon is pressed to obtain the Select this when the color temperature is between 4500K and 8500K. Select this when the color temperature is between 1700K and 11000K (Ex. Sodium light inclusion) Select this to fine-tune White Balance manually. You can adjust the blue and red tone level manually. Select one according to the locaon of camera installaon. Then, select one sub-mode from AUTO, MANUAL, SHUTTER, PRIORITY, IRIS PRIORITY, and BRIGHT. IRIS and SHUTTER are controlled automacally. IRIS, GAIN, and SHUTTERf are controlled manually. Manual SHUTTER and GAIN control with automac IRIS control. Manual IRIS and GAIN control with automac SHUTTER control. IRIS and GAIN can be controlled by control of BRIGHTNESS. 0~20: Adjust the screen brightness. MANUAL: BRIGHTNESS control is fixed, and give the exposure control priority to other resources. 0~17: Adjust the IRIS screen brightness. AUTO: IRIS controls exposure automacally but SHUTTER is fixed. MANUAL: IRIS control is fixed, and give the exposure A funcon which controls the amplificaon/gain process automacally if the illuminaon falls under the usable level. 1/2~40K: Adjust the SHUTTER speed. (1/2, 4, 8, 15, 30, 60, 90, 120, 150, 180, 250, 350, 500, 725, 1000, 1500, 2K, 3K, 4K, 6K, 10K, 20K, 30K, 40K) OFF~1/1: Adjust the level of DSS. (OFF, 1/30, 1/15, 1/8, 1/4, 1/2) When it is in low luminance condion, DSS can adjust the picture quality by maintaining the light Use this funcon when you experience picture flicker, this happens when there is a conflict with the installed lighng frequency. Automacally adjusts the focus posion. Manually adjusts the focus posion when zoom is changed. When this mode is enabled, it will automacally adjusts the focus posion only when the zoom is changed. Set the zoom speed. Set the limit of the tele. Set the limit of the wide. Set the distance limit for the far focusing. The lens moves to adjust the focus from the distance. Set the priority distance limit for near focusing. AUTO: The focus is automacally adjusted at the pre-set interval (01~07). ONE PUSH: The focus is re-adjusted when the OSD buon is pushed over ONE PUSH. This funcon is to set user defined zoom and focus posion. Up to 32 preset posion can be set with sub menu, USER PRESET, ACTIVE, SAVE, RESET. Enable user to view both object and background more clearly when background is too bright. Set the WDR-LEVEL (0~4). Enable a back light compensaon feature. Enables a user to select a desired area on a picture and view that area more clearly when background is too bright. Brightness correcon of the dark image area. Adjust the GAIN level (LOW, MIDDLE, HIGH). Highlight the bright area with a masking box with a selected color. Adjust the masking level (0~20). Select the color for masking (GRN, MAG, RED, BLUE, BLK, WHT, YEL, CYN) The camera will stay in DAY in a normal environment, but switched to NIGHT mode when ambient illuminaon become this pre-set level. Set the margin between Day Night switching level and Night Day switching level. Different exposure gain level is needed to avoid malfuncons. Select the checking me of light condion to confirm to chage from the day mode to the night mode. Night burst OFF makes that the color burst is removed when ICR switches to black/white. The picture is always displayed in color. The picture is always displayed in black/white. The camera will stay in DAY in a normal environment, but switched to NIGHT mode when ambient illuminaon become this pre-set level. Select the interval me from the day mode to the night mode. Alters the color burst informaon passed to the video monitor. Adjust the color level value for a fine color tune. As you increase this value, the picture outline becomes stronger and clearer. Video output will be flipped (MIRROR-HORIZONTALLY, FLIP-VERTICALLY, ROTATION). This feature will help increase visibility in extreme weather condions, such as fog, rain or in a very strong luminous intensity. This feature will reduce the video noise at low ambient light. This feature will observe the object movement by moon zone and sensivity that are pre-set with sub menu, DET. SIZE, SENSITIVITY, MASK ACTIVE, WIDTH, This feature will correct the inconsistent brightness level in the image. This feature will adjust video output brightness (STANDARD, STRAIGHT, LOW, MIDDLE, HIGH). Change video output specificaon. CV350-10X: 1080P25/30, 1080i50/60, 720P50/60, 1080P50/60. CV350-5XB: 1080P29.97, 1080i59.94, 1080P59.94, 720P59.94 The camera tle can be entered and it will appear over the video output. Turn On or off of the zoom scale display. Mask an area you want to hide on the screen with sub menu, MASK NO, MASK ACTIVE, MASK COLOR, WIDTH, HEIGHT, MOVE HOR, MOVE VER, TRANS, RESET Select the camera ID number. Select the display of camera ID. Set the baudrate of RS-485 communicaon (2400, 4800, 9600, 19200, 38400, 57600, 115200). You can select the menu language according to your requirements. ( ENGLISH, , FRANÇAIS, DEUTSCH, ESPAÑOL, PORTUGUÊS, ) Defecve pixels can be corrected. Display the firmware version. Reset the camera sengs to the factory defaults. Exit the setup. Design and specifications are subject to change without notice. Marshall Electronics