Manuals+

3mk Fuego User Manual

Product Overview

The 3mk Fuego is a portable Bluetooth speaker designed to deliver a rich audio experience. This manual provides instructions on its usage, features, and specifications.

Package Contents

The package includes the Fuego speaker and a Type-C charging cable.

Diagram: A visual representation of the speaker and its components.

Device Layout

The speaker features the following buttons and ports:

Getting Started

Turning the Device On/Off

To turn the device on or off, press and hold the power button for 2 seconds. The Bluetooth connection is automatically interrupted 30 minutes after playback ends. The device powers off automatically 10 minutes after the Bluetooth connection is terminated.

Diagram: Shows pressing and holding the power button for 2 seconds to turn the device on/off.

Bluetooth Connection

Place the speaker within 1 meter (3.3 ft) of your device. Press and hold the power button for 2 seconds to enter Bluetooth pairing mode. The Bluetooth indicator will flash white during pairing and turn solid blue when a connection is established.

Diagram: Illustrates connecting the speaker to a phone via Bluetooth settings.

Playback and Volume Control

Press the Pause/Play button once to start or stop playback. Press the Volume+/Next Track button to increase volume. Press the Volume-/Previous Track button to decrease volume. Press and hold the Volume+/Next Track button to skip to the next track. Press and hold the Volume-/Previous Track button to skip to the previous track.

Diagram: Shows single press for play/pause and press-and-hold for track skipping.

Dual EQ Modes

The speaker offers two equalizer modes: EQ1 (General EQ) and EQ2 (Bass Boost EQ). Double-press the TWS/EQ button to switch between modes. EQ1 is the default equalizer, indicated by a solid blue LED. EQ2 is indicated by a flashing blue LED.

Diagram: Illustrates the EQ button and the LED indicators for different EQ modes.

TWS Pairing (True Wireless Stereo)

To connect two speakers wirelessly:

  1. With both speakers off, simultaneously press and hold the power buttons for 2 seconds to enter Bluetooth search mode (blue LED flashes).
  2. Press the TWS/EQ button once on one speaker. The LED will stop flashing and turn solid blue, indicating a successful TWS connection.

Diagram: Shows the process of pairing two Fuego speakers for TWS functionality.

Switching Between Two Bluetooth Devices

To switch between paired Bluetooth devices, follow these steps:

  1. Ensure both devices (e.g., Phone A and Phone B) are within Bluetooth range.
  2. Navigate to the Bluetooth settings on the device you wish to connect to and select 'Fuego'.

Diagram: Illustrates the process of switching active Bluetooth connections between two phones.

How to Charge

1. Insert the Type-C cable into the speaker and connect the USB-A end to a computer or power adapter. Alternatively, use a Type-C fast charger (not included). The speaker's indicator light will turn red during charging and turn off when fully charged. Standard charging time is approximately 3.5 hours.

2. The speaker can be used while charging.

For first-time battery use, perform an initial calibration: use the speaker until the battery is completely depleted, then fully recharge it. Three full charge cycles are recommended to reach maximum battery capacity.

Diagram: Shows the Type-C port and the charging indicator LED behavior.

Factory Reset

To reset the speaker to factory settings, press and hold the Bluetooth connection button (TWS/EQ button) for 7 seconds. You will hear a sound indicating that the factory settings have been restored.

Diagram: Shows pressing and holding the TWS/EQ button for 7 seconds for a factory reset.

Specifications

Name 3mk Fuego
Transducers 45mm + 30mm
Frequency 70-20,000Hz
Impedance 4Ω ± 15%
Sensitivity 81dB ± 3dB
Max Power 30W
Cable Length 0.8m
Bluetooth Version 5.3
Water Resistance IPX7
Low Latency in Bluetooth Mode <180ms
Playback Time Up to 12h
Bluetooth Signal Range 10m
Charging Time 3.5h
Standby Time Up to 300 days
Battery Capacity 5200mAh
Charging Voltage DC 5V
Weight 620g
Charging Port USB-C

Storage

Store the speaker in a clean, dry, and ventilated place at an ambient temperature between +5 and 40°C. Avoid contact with corrosive substances and keep the product away from fire and heat sources. Charge the device once every six months when not in use.

Usage Tips

Disposal and Recycling Information

This symbol on the product, battery, documentation, or packaging indicates that at the end of its useful life, the product and batteries should be disposed of at designated separate collection points by local authorities. This ensures that WEEE are recycled and treated in a way that preserves valuable materials and protects human health and the environment.

Declaration of Conformity

3mk Protection sp. z o.o. hereby declares that this product complies with the essential requirements and other provisions of Directive 2014/53/EU.

More Information

Visit www.3mk.global/fuego for more details.

Company Information:

3mk Protection sp. z o.o.
Krotoszyńska 35, B-02/4a
63-400 Ostrów Wielkopolski, Poland
VAT ID PL 6222833086

Designed in Poland by 3mk Protection. Made in China.

Certifications: CE, RoHS, UKCA

Models: Fuego Speaker, Fuego, Speaker

PDF preview unavailable. Download the PDF instead.

3mk-fuego-manual Adobe PDF library 17.00 Adobe Illustrator(R) 24.0

Related Documents

Preview 3mk Fuego Bluetooth Speaker User Manual and Quick Start Guide
Comprehensive guide for the 3mk Fuego Bluetooth speaker, detailing charging, switching between two Bluetooth devices, and automatic power-off features.
Preview 3mk Drive & Charge™ Wireless Car Charger User Manual and Guide
Official user manual for the 3mk Drive & Charge™ wireless car charger. Learn about specifications, installation, features, usage, safety guidelines, and compliance for your Qi-enabled car charging solution.