MODSTER E-LONGBOARD User Manual
Introduction
Thank you for purchasing our electric skateboard. Please note that an electric skateboard is not a toy. Take time to learn it and read this manual carefully, particularly the safety instruction pages.
We hope you will enjoy this product and have lots of fun with it in the future!
Specifications
| Feature | Specification |
|---|---|
| Speed | up to 35Km/h |
| Mileage | up to 16Km |
| Max load | up to 120Kg |
| Climbing ability | 16° |
| Watts | 2x450W |
| Motor Type | Hub motor in wheel |
| Weight (N.W.) | 6.7Kg |
| Weight (G.W.) | 9Kg |
| Wheel | PU, 90x52mm, hardness 80A |
| Board | 5 layer maple + 2 layers bamboo |
| Voltage | 36V |
| Capacity | 4Ah |
| Battery Type | Lithium Battery |
| Battery Weight | 1000g |
| Charge Time | 4 hours |
| Remote Frequency | 2.4GHz |
| Remote Control Distance | 14m |
| Product Size | 930*265*125mm |
| Packaging Size | 1000*315*215mm |
Preparation
- Make sure your helmet and protective gear are ready. ?
- Confirm the correct direction of the skateboard. ➡️
- Confirm the position on the skateboard. Feet should stand on the widest front and back parts of the skateboard.
- Use the low speed mode to become familiar with the acceleration and braking of the skateboard. ?
- Use the brake function of the remote to stop the skateboard. First, place your front foot down, then your back foot. ?
Parts Diagram
The electric skateboard consists of the following main parts:
- 1: Hub motor Drive
- 2: Dual motor
- 3: Deck
- 4: Power truck set
- 5: Controller
- 6: Battery pack
- 7: Remote control
- 8: Wheel
- 9: Power button
- 10: Charging port
Remote Control
The remote control allows you to operate the skateboard:
- 1: Speed control (joystick)
- 2: Go forward button
- 3: Brake button
- 4: Speed mode toggle (High, Middle, Low)
- 5: Power switch
- 6: Battery display (shows remaining charge: 100%, 50%, 10%)
- 7: Pair button
- 8: Charging port
Pairing Instructions
The Board and Remote must be paired before first use. Ensure both are turned off initially.
- Turn on the board: Press the power button for 5 seconds. The power button light will flash.
- Turn on the remote, then press the pair button. The signal indicator and power button indicator will flash. A faster flash indicates successful pairing.
- Test the controls: Push the joystick forward to test acceleration and backward to test braking. If both functions work correctly, the board is ready for normal use.
Safety Instructions
Important Safety Information:
- The electric skateboard is not a toy and should be treated with appropriate caution. Always prioritize safety, as losing balance can lead to collisions or falls. Use the board in a safe, appropriate environment and always wear safety gear. ⚠️
- Safety Gear: We recommend wearing full safety gear, including a suitable skateboard helmet, elbow pads, knee pads, and gloves. ?
- Footwear: Wear appropriate shoes. Flip-flops or similar loose footwear are not suitable for riding. ?
- Age and Load Limit: The skateboard is designed for riders aged 14 years and above. Only one person should ride at a time. The maximum load is 120Kg. Exceeding this weight can compromise the structural integrity, remote functionality, and may lead to board damage or loss of control. ⚖️
- Traffic Laws: Please observe your local traffic laws and regulations. ?
- Riding Surface: The board is designed for flat, paved surfaces. Avoid driving on sand, gravel, mud, rugged, or uneven ground. Do not drive on slippery surfaces like snow, ice, or wet ground. ?️
- Moving Parts: Keep fingers, hair, and clothing away from motors, wheels, and other moving parts. ?
- Electronics: Do not open or tamper with the electronics housing. Electric shock is possible, and this will void the warranty. ⚡
- Battery Storage: Do not store the board with an empty battery. Charge the battery at least every 3 months. ?
Note on Performance: Range, maximum speeds, and incline ability are heavily dependent on factors such as battery charge level, ground condition, inclines/declines, rider weight, rider performance, weather conditions, headwind, and other variables. The provided information relates to optimal conditions.
Declaration of Conformity
MSG Online GmbH declares that the products comply with the essential requirements and other relevant provisions of the Electromagnetic compatibility (EMC) Directive 2014/30/EU, Machinery Directive 2006/42/EC, Low Voltage Directive 2014/35/EU (for Charger), Radio and Telecommunication Terminal Equipment (RTTE) Directive 2014/53/EU (for remote Control), and RoHS Directive 2011/65/EU.
Manufactured in accordance with harmonized standards including EN-61000-3-3, EN-55032, EN 301 489-1, EN 301 489-17, EN ISO 1210, EN 60204-1, EN-60335-1, EN 62233, EN 300 220-1, EN 300 2020-2, EN 300 328, and EN-62311.
For the current version of the operating instructions, please visit our website: www.modster.at.
Manufacturer/responsible Person: Walter Bittdorfer, Managing Director, MSG Online GmbH, Wirtschaftspark 9, 8530 Deutschlandsberg, Austria. Date: 18.08.2021.
