Niko Swiss Garde 360 Presence DALI Master A-Comfort 24m

Safety Notes

[Warning] Ensure that electrical lines are de-energised before installation. Installation is only permitted by qualified electricians in compliance with local legislation.

The installation of products that will permanently be part of the electrical installation and which include dangerous voltages, should be carried out by a qualified installer and in accordance with the applicable regulations. This user manual must be presented to the user, included in the electrical installation file, and passed on to any new owners. Additional copies are available on the Niko website or via Niko customer services.

Installation

Placement

The detector responds to movements and heat in its environment. Avoid installation in close proximity to heat sources such as stoves, electric heaters, fans, or other moving objects, as these may trigger unintended activation.

The presence detector is designed for ceiling mounting.

Range and Detection Area

The detector provides 360-degree detection. The maximum detection range for presence is Ø 6 meters, extending to approximately Ø 24 meters at a mounting height of 3 meters. The detection range varies with height:

• At 2m height: presence range Ø 2m, total range Ø 16m.
• At 2.5m height: presence range Ø 3.5m, total range Ø 20m.
• At 3m height: presence range Ø 6m, total range Ø 24m.
• At 3.5m height: presence range Ø 6m, total range Ø 24m.

To reduce the detection area, enclosed half-shells can be clamped between the lens and the cover.

The range can be increased with up to 10 secondary presence detectors (Edition UP Art. No 41752 or Edition AP Art. No 41753). For disruption-free detection when using several detectors, ensure an approximate 30% overlap of the detection areas.

Wiring

Wire the presence detector according to the wiring diagram. All DALI devices are wired in parallel. The Master device automatically recognises connected DALI devices.

[Warning] Do not connect additional DALI power supplies nor multiple Master devices, as this would damage the DALI coils as well as the presence detectors. The presence detector contains an in-built DALI power supply; do not connect an external DALI power supply.

The DALI wiring diagram shows connections for Master and Secondary units. Master unit connections include L1, L2, N, DA+, DA-, T1+2, T3, T4. Secondary unit connections include L, N, DA, DA. Zones 1, 2, 3, and 4 are indicated.

Setup Mode: "Out of the Box"

Connect the presence detector to mains voltage only after the installation is completely wired. Allow approximately 40 seconds warm-up delay after mains connection for the detector to become operational. DALI ballasts will be automatically recognised by the presence detector.

Upon connection to mains voltage, all connected lights switch on, and the presence detector operates in On/Off mode with a default delay time of 15 minutes. All zones can be switched on and off via connected 230V push-buttons or via the P-IR remote control; all 230V push-buttons will have the same functionality.

Note: All LEDs (red, blue, yellow, green) flash alternately, indicating that the presence detector is in "Out-of-the-box" mode.

Commissioning and programming are described in the operating instructions.

Technical Data

Compliance and Environment

CE Marking

This product complies with all relevant European guidelines and regulations. For radio equipment, Niko declares that the radio equipment in this manual conforms with the 2014/53/EU directive. The full text of the EU declaration of conformity is available at www.niko.eu under the product reference, if applicable.

Environment

This product and/or the batteries provided cannot be disposed of as non-recyclable waste. Take your discarded product to a recognised collection point. Customers play an important role in the promotion of sorting, recycling, and reuse of discarded electrical and electronic equipment. Recycling charges may be levied by the government in certain cases to finance waste collection and treatment, and are included in the price of this product.

Packaging: Cardboard and Paper Packaging to be Sorted.

Support & Contact

Niko nv
Industriepark West 40
9100 Sint-Niklaas, Belgium
www.niko.eu

Contact Information:

• EN: +32 3 778 90 80 | support@niko.eu
• FR (Switzerland): +41 44 878 22 22 | support.ch@niko.eu
• DE (Germany): +49 7623 96697-0 | support.de@niko.eu
• DE (Switzerland): +41 44 878 22 22 | support.ch@niko.eu
• DE (Austria): +43 1 7965514 | support.at@niko.eu
• IT (Switzerland): +41 44 878 22 22 | support.ch@niko.eu
• PL: +48 509 378 373 | support.pl@niko.eu

Niko prepares its manuals with the greatest care and strives to make them as complete, correct, and up-to-date as possible. Nevertheless, some deficiencies may subsist. Niko cannot be held responsible for this, other than within the legal limits. Please inform Niko customer services of any deficiencies in the manuals at support@niko.eu.