HOBOconnect Monitoring App HOBOconnect | Onset's HOBO Data LoggersHOBO® MX Water Level Logger (MX2001-0x) Manual | Onset's HOBO and InTemp Data Loggers
User Guide for HOBO models including: MX2001 MX Water Level Logger, MX2001, MX Water Level Logger, Water Level Logger, Level Logger, Logger
2 days ago — HOBO MX Water Level Logger (MX2001) Quick Start Guide. 19388-N MAN-QSG-MX2001. Before you begin: After completing steps 1–4, we recommend that you perform ...
HOBO MX Water Level Logger (MX2001) Quick Start Guide. 19388-N MAN-QSG-MX2001. Before you begin: After completing steps 1–4, we recommend that you perform ...
HOBO MX Water Level Logger (MX2001) Quick Start Guide. 19388-N MAN-QSG-MX2001. Before you begin: After completing steps 1–4, we recommend that you perform ...
File Info : application/pdf, 2 Pages, 804.23KB
DocumentDocumentHOBO® MX Water Level Logger (MX2001) Quick Start Guide Before you begin: After completing steps 14, we recommend that you perform a trial run of steps 5 through 11 before deploying the logger. IMPORTANT: When assembling the logger or attaching the cable, make sure the O-rings and mating housing surfaces are clear of any debris. Any contamination of these surfaces can cause leaks that will lead to logger failure. 1 Install the batteries in the top end. Unscrew the end cap and pull out the board. Apply a small amount of the fresh dielectric grease (included) to the battery terminals. Insert the included two AA batteries observing polarity as shown on the board. Reinsert the board. Screw the cap back on until hand tight. Unscrew end cap Remove board and install batteries Top end 2 Connect the top end to the sensor end with the water level logger cable as shown here. The end of the cable with the longer housing connects to the top end as shown below. Plug this portion of the cable with the longer housing into the top end and screw to tighten (hand tight). Top end Sensor end Plug this portion of the cable with the shorter housing into the sensor end and screw to tighten (hand tight). 3 · Download HOBOconnect® to a phone or tablet from the App Store® or Google PlayTM. · Download HOBOconnect to a Windows® computer from www.onsetcomp.com/products/software/hoboconnect. 4 Open the app. Enable Bluetooth® in your device settings if prompted. 5 Tap Devices in the app. The logger should appear in the list of devices. If it does not appear, make sure it is within range of your phone, tablet, or computer. (Note that the serial number shown in the app is for the top end of the logger). 6 If you are ready to deploy the logger, place it in the deployment location. Refer to the logger manual at www.onsetcomp.com/resources/documentation/19389-mx2001-manual for deployment guidelines. Otherwise, skip deployment and complete the following steps as a test. Tap the logger tile in the app to connect to the logger and tap Configure & Start to set up the logger. 7 19388-N MAN-QSG-MX2001 8 9 10 11 Scroll down in the Configuration screen to select the measurement parameters you want to log. Enable differential pressure if you want water level. Make sure that temperature is enabled if you want water level, absolute pressure, or differential pressure. Select any other logger settings as desired and then tap Start to save the settings to the logger. The logger begins logging data based on the settings you selected. In the logger screen: a. Tap Calibrate. b. Enter a Reference Water Level and select the unit type. Enter the Reference Water Level at the time the current deployment started logging. c. Select a different water density if necessary or enter your own next to Manual Input. d. Tap Save. Changes take effect immediately. This also creates reference water level and water density events in the data file. e. Note: You can also edit the water parameters after you have downloaded data from the logger by tapping viewing a data file. See Using the Data File Viewer for details. when To download data from the logger to your device, tap Devices. Connect to the logger and tap Download Data. To view or export the data, tap Data, tap (if applicable), and tap . For detailed specifications and information about this logger, refer to the HOBO® MX Water Lever Logger (MX2001-0x) Manual at: www.onsetcomp.com/resources/documentation/19389-mx2001-manual or scan the code at the left. © 20152023 Onset Computer Corporation. All rights reserved. Onset, HOBO, and HOBOconnect are registered trademarks of Onset Computer Corporation. App Store is a service mark of Apple Inc. Google Play is a trademark of Google LLC. Windows is a registered trademark of Microsoft Corporation. Bluetooth is a registered trademark of Bluetooth SIG, Inc. All other trademarks are the property of their respective companies. This product has been manufactured by Onset Computer Corporation and in compliance with Onset's ISO 9001:2015 Quality Management System. Patent #: 8,860,569 19388-N MAN-QSG-MX2001