Important Notice
This evaluation board/kit or development tool is designed for engineering evaluation, demonstration, or development purposes only. It is not intended for use in finished products. It is intended for use by electronics engineers and is not a consumer product. Seiko Epson assumes no responsibility or liability for any damage or fire caused by its use. Users should cease use if any abnormal issue occurs. Components may be changed without notice.
NOTICE: No part of this material may be reproduced without written permission from Seiko Epson. Seiko Epson reserves the right to make changes without notice. Seiko Epson disclaims liability for inaccuracies or application issues. This material does not grant intellectual property rights. Export of products or technology must comply with applicable laws and regulations. Products and technical information must not be used for the development or manufacture of weapons of mass destruction or for military purposes. All brands and product names are trademarks of their respective companies.
©SEIKO EPSON CORPORATION 2018-2019. All rights reserved.
Introduction
The S5U13C00P01C100 is the S1D13C00 EPD Evaluation Board. It functions as a BoosterPack board with a connector for the E Ink ET011TT2 EPD panel. It is designed for direct connection to the TI Tiva C Series EK-TM4C1294XL Launchpad evaluation board, enabling the evaluation and development of embedded EPD applications using the Epson S1D13C00 Memory Display Controller IC. It can also be controlled by the ST Nucleo-F746ZG or Nucleo-F767ZI board via the S5U13C00M00C100 (STM32 Nucleo-144 development board).
Figure 1: S5U13C00P01C100 EPD Evaluation Board: A visual representation of the evaluation board, showing its physical layout and connectors.
The S5U13C00P01C100 EPD Evaluation Board includes:
- A S1D13C00 Memory Display Controller (U1).
- Four 2x10 connectors (J4, J5, J6, J7) for Host Interface connection and +5V/+3.3V power.
- A 16Mbytes QSPI Serial Flash (U2).
- A flexible printed circuit (FPC) connector (CN2) for connecting to an ET011TT2 EPD panel.
- An 18-pin right-angle header connector for connecting to other panels.
Figure 1.1: S5U13C00P01C100 Block Diagram for Interface: This block diagram illustrates the board's interfaces. It features a host MCU interface and three display interfaces: CN1 for E Ink's HULK power board, CN2 for the ET011TT2 panel module, and through holes for connecting to a memory display panel. CN2 can also connect to other E Ink panel modules. The booster components on the board are similar to those on the HULK power board, suitable for the ET011TT2 panel module.
Connecting the ET011TT2 EPD Panel
Figure 2: Connecting the ET011TT2 EPD Panel: An image demonstrating the physical connection of the ET011TT2 EPD panel to the evaluation board.
Figure 2.1: Connecting the HULK Power Board with ET011TT2 EPD Panel: An image showing the HULK Power Board connected to the ET011TT2 EPD Panel.
Connecting to the Host MCU Board
3.1 EK-TM4C1294XL Board
To connect the S5U13C00P01C100 EPD Evaluation Board to the EK-TM4C1294XL Launchpad Board, position the evaluation board on top of the Launchpad board and press them together. Ensure J4 connects to X8, J5 to X9, J6 to X6, and J7 to X7.
Figure 3: Connecting the S5U13C00P01C100 to the EK-TM4C1294XL: This image shows the physical arrangement of the S5U13C00P01C100 board stacked on top of the EK-TM4C1294XL Launchpad, with connectors aligned.
3.2 Nucleo-F746ZG or Nucleo-F767ZI Board
First, connect the S5U13C00M00C100 adapter board to the Nucleo board. Then, connect the S5U13C00P01C100 board to the S5U13C00M00C100 adapter board.
Figure 3.1: Connecting the S5U13C00P01C100 to the Nucleo-F746ZG or Nucleo-F767ZI: This image displays the sequence of connections involving the Nucleo board, the S5U13C00M00C100 adapter board, and the S5U13C00P01C100 evaluation board.
Jumpers Settings
The following tables detail the jumper settings for the S5U13C00P01C100 EPD Evaluation Board.
Figure 4: S5U13C00P01C100 Jumpers Locations: An image highlighting the locations of various jumpers (JP2, JP3, JP4, JP6, JP7) on the evaluation board.
| Jumpers | Descriptions | Type | Default Position |
|---|---|---|---|
| JP2 | External VC3 Connection | 2-pin | Not installed |
| JP3 | VDD_IC supply series jumper | 2-pin | Installed |
| JP4 | VDD_EPD supply series jumper | 2-pin | Installed |
| JP6 | DISPVDD source supply 1-2 = VDD_EPD 2-3 = VMDL | 3-pin | 1-2 (VDD_EPD) |
| JP7 | HIFCNF (host interface configuration) 1-2 = SPI/QSPI 2-3 = INDIRECT 8-BIT (not used) | 3-pin | 1-2 (SPI/QSPI) |
Push-Buttons and EPD Panel Connectors
5.1 Push-Buttons
Figure 5: S5U13C00P01C100 Push-Buttons and EPD Panel Connector Locations: An image indicating the positions of push-buttons (SW1, SW2) and connectors (CN1, CN2) on the board.
| Push-Button | Description |
|---|---|
| SW1 | Reset button |
| SW2 | User button connected to P01 port pin |
5.2 Header for Hulk Power Board Connection (CN1)
The table below shows the pin assignments of CN1:
| CN1 Pin | Pin name | Description |
|---|---|---|
| 1 | VDD_EPD | Power supply for EPD panel. |
| 2 | EPD_BS | Tied to VDD_EPD through resistor R49. EPD bus select. 3-wire serial interface is selected. |
| 3 | EPD_RST | Connected to port P03 of S1D13C00. EPD reset output from S1D13C00. |
| 4 | EPD_BUSY | Connected to port P02 of S1D13C00. EPD busy input status to S1D13C00. |
| 5 | HST/EPD_CSB | Chip-select for EPD panel. Connected to HST output of S1D13C00. |
| 6 | VCK/EPD_DC | Data/command select for EPD panel. Connected to VCK output of S1D13C00. |
| 7 | EPD_P51 | Connected to P06 port of S1D13C00. |
| 8 | - | - |
| 9 | - | - |
| 10 | P07 | Connected to P07 port of S1D13C00. |
| 11 | - | - |
| 12 | VST/EPD_SCL | Serial clock for EPD panel. Connected to VST output of S1D13C00. |
| 13 | - | - |
| 14 | ENB/EPD_SDA | Serial data for EPD panel. Connected to ENB output of S1D13C00. |
| 15 | - | - |
| 16 | GND | Ground. |
5.3 FPC Connector for ET011TT2 Connection (CN2)
The following table shows the pinout and signal connections of the 24-pin FPC (CN2):
| CN2 Pin | Pin Connection | Description |
|---|---|---|
| 1 | EPD_P51 | Connected to P06 port of S1D13C00. |
| 2 | FETG | GDR signal of EPD panel. |
| 3 | FETS | RESE signal of EPD panel. |
| 4 | VGL | VGL supply from EPD panel. |
| 5 | VGH | VGH supply from EPD panel. |
| 6 | EPD_TSCL | I2C clock for external temperature sensor on EPD panel. |
| 7 | EPD_TSDA | I2C data for external temperature sensor on EPD panel. |
| 8 | EPD_BS | Tied to VDD_EPD through resistor R49. EPD bus select. 3-wire serial interface is selected. |
| 9 | EPD_BUSY | Connected to port P02 of S1D13C00. EPD busy input status to S1D13C00. |
| 10 | EPD_RST | Connected to port P03 of S1D13C00. EPD reset output from S1D13C00. |
| 11 | VCK/EPD_DC | Data/command select for EPD panel. Connected to VCK output of S1D13C00. |
| 12 | HST/EPD_CSB | Chip-select for EPD panel. Connected to HST output of S1D13C00. |
| 13 | VST/EPD_SCL | Serial clock for EPD panel. Connected to VST output of S1D13C00. |
| 14 | ENB/EPD_SDA | Serial data for EPD panel. Connected to ENB output of S1D13C00. |
| 15 | VDD_EPD | VC1 supply to EPD panel. (No-connect on panel side.) |
| 16 | VDD_EPD | VC1 supply to EPD panel. |
| 17 | GND | Ground. |
| 18 | VDD | VDD supply from EPD panel. |
| 19 | P07 | Connected to P07 port of S1D13C00. |
| 20 | VSH | VSH supply from EPD panel. |
| 21 | PREVGH | PREVGH supply to EPD panel. |
| 22 | VSL | VSL supply from EPD panel. |
| 23 | PREVGL | PREVGL feedback from EPD panel. |
| 24 | VCOM_EPD | VCOM supply from EPD panel. |
Pre-installed On-board Components
Figure 6: S5U13C00P01C100 pre-installed on-board components locations: An image showing the location of key pre-installed components, including U2.
6.1 16Mbytes QSPI Serial Flash (U2)
This serial flash memory is directly connected to the QSPI interface of the S1D13C00. The flash can be accessed (read-only) through the Memory-Mapped Access area on the memory map of the S1D13C00.
Host MCU Board Connections
7.1 Tiva C Series EK-TM4C1294XL Launchpad
The following tables detail the signal connections between the Tiva C Series EK-TM4C1294XL Launchpad connectors and the S5U13C00P01C100 Customer Development Board:
| J4 | EK-TM4C1294XL Connector X8 Signals | S5U13C00P01C100 Signal |
|---|---|---|
| 1 | 3V3 | - |
| 2 | 5V | HOST_5V |
| 3 | PE4 | HIFD0 |
| 4 | GND | GND |
| 5 | PC4 | HIFD7 |
| 6 | PE0 | - |
| 7 | PC5 | HIFD6 |
| 8 | PE1 | - |
| 9 | PC6 | HIFD5 |
| 10 | PE2 | - |
| 11 | PE5 | HIFD1 |
| 12 | PE3 | - |
| 13 | PD3 | - |
| 14 | PD7 | - |
| 15 | PC7 | HIFD4 |
| 16 | PA6 | - |
| 17 | PB2 | - |
| 18 | PM4 | P11 |
| 19 | PB3 | HIFRD |
| 20 | PM5 | HIFIRQ |
| J5 | EK-TM4C1294XL Connector X9 Signals | S5U13C00P01C100 Signal |
|---|---|---|
| 1 | PF1 | - |
| 2 | GND | GND |
| 3 | PF2 | - |
| 4 | PM3 | - |
| 5 | PF3 | - |
| 6 | PH2 | - |
| 7 | PG0 | - |
| 8 | PH3 | - |
| 9 | PL4 | - |
| 10 | TARGET_RST# | nRST |
| 11 | PL5 | - |
| 12 | PD1 | - |
| 13 | PL0 | - |
| 14 | PD0 | - |
| 15 | PL1 | - |
| 16 | PN2 | - |
| 17 | PL2 | - |
| 18 | PN3 | - |
| 19 | PL3 | - |
| 20 | PP2 | - |
| J6 | EK-TM4C1294XL Connector X6 Signals | S5U13C00P01C100 Signal |
|---|---|---|
| 1 | 3V3 | HOST_3.3V |
| 2 | 5V | HOST_5V |
| 3 | PD2 | - |
| 4 | GND | GND |
| 5 | PP0 | - |
| 6 | PB4 | HIFDE |
| 7 | PP1 | - |
| 8 | PB5 | HIFWR |
| 9 | PD4 | HIFD2 |
| 10 | PK0 | - |
| 11 | PD5 | HIFD3 |
| 12 | PK1 | - |
| 13 | PQ0 | - |
| 14 | PK2 | - |
| 15 | PP4 | - |
| 16 | PK3 | - |
| 17 | PN5 | - |
| 18 | PA4 | - |
| 19 | PN4 | - |
| 20 | PA5 | - |
| J7 | EK-TM4C1294XL Connector X7 Signals | S5U13C00P01C100 Signal |
|---|---|---|
| 1 | PG1 | - |
| 2 | GND | GND |
| 3 | PK4 | - |
| 4 | PM7 | - |
| 5 | PK5 | - |
| 6 | PP5 | - |
| 7 | PM0 | - |
| 8 | PA7 | - |
| 9 | PM1 | - |
| 10 | TARGET_RST# | - |
| 11 | PM2 | - |
| 12 | PA3/PQ2 | - |
| 13 | PH0 | - |
| 14 | PA2/PQ3 | - |
| 15 | PH1 | - |
| 16 | PP3 | HIFCS |
| 17 | PK6 | - |
| 18 | PQ1 | - |
| 19 | PK7 | - |
| 20 | PM6 | - |
7.2 STM32 Nucleo-144 development board
The following tables map the signal connections between the S5U13C00P01C100 board and the STM32 Nucleo-144 development board:
| S5U13C00P01C100 Board | STM32 Nucleo-144 development board | Description | ||
|---|---|---|---|---|
| Signal | Signal | |||
| J4-1 | - | - | - | |
| J4-2 | HOST_5V | +5V | CN8-9 | 5V supply |
| J4-3 | HIFD0 | PD11 | CN10-23 | Host SPI/QSPI D0 |
| J4-4 | GND | GND | CN7-8 | Ground |
| J4-5 | HIFD7 | PE10 | CN10-24 | Host INDIRECT8 D7 |
| J4-6 | - | - | - | - |
| J4-7 | HIFD6 | PE9 | CN10-4 | Host INDIRECT8 D6 |
| J4-8 | - | - | - | - |
| J4-9 | HIFD5 | PE8 | CN10-18 | Host INDIRECT8 D5 |
| J4-10 | - | - | - | - |
| J4-11 | HIFD1 | PD12 | CN10-21 | Host SPI/QSPI D1 |
| J4-12 | - | - | - | - |
| J4-13 | - | - | - | - |
| J4-14 | - | - | - | - |
| J4-15 | HIFD4 | PE7 | CN10-20 | Host INDIRECT8 D4 |
| J4-16 | - | - | - | - |
| J4-17 | - | - | - | - |
| J4-18 | - | - | - | - |
| J4-19 | HIFRD | PD4 | CN9-8 | Host INDIRECT8 read signal |
| J4-20 | HIFIRQ | PB1 | CN10-7 | Interrupt request to host |
| S5U13C00P01C100 Board | STM32 Nucleo-144 development board | Description | ||
|---|---|---|---|---|
| Signal | Signal | |||
| J5-1 | - | - | - | |
| J5-2 | GND | GND | CN10-22 | Ground |
| J5-3 | - | - | - | - |
| J5-4 | - | - | - | - |
| J5-5 | - | - | - | - |
| J5-6 | - | - | - | - |
| J5-7 | - | - | - | - |
| J5-8 | - | - | - | - |
| J5-9 | - | - | - | - |
| J5-10 | nRST | NRST | CN8-5 | Reset |
| J5-11 | - | - | - | - |
| J5-12 | - | - | - | - |
| J5-13 | - | - | - | - |
| J5-14 | - | - | - | - |
| J5-15 | - | - | - | - |
| J5-16 | - | - | - | - |
| J5-17 | - | - | - | - |
| J5-18 | - | - | - | - |
| J5-19 | - | - | - | - |
| J5-20 | - | - | - | - |
| S5U13C00P01C100 Board | STM32 Nucleo-144 development board | Description | ||
|---|---|---|---|---|
| Signal | Signal | |||
| J6-1 | HOST_3.3V | +3V3 | CN8-7 | 3.3V supply |
| J6-2 | HOST_5V | +5V | CN8-9 | 5V supply |
| J6-3 | - | - | - | - |
| J6-4 | GND | GND | CN10-3 | Ground |
| J6-5 | - | - | - | - |
| J6-6 | HIFDE | PB6 | CN10-13 | Host device enable signal |
| J6-7 | - | - | - | - |
| J6-8 | HIFWR | PB2 | CN10-15 | Host SPI/QSPI clock |
| J6-9 | HIFD2 | PE2 | CN10-25 | Host SPI/QSPI D2 |
| J6-10 | - | - | - | - |
| J6-11 | HIFD3 | PD13 | CN10-19 | Host SPI/QSPI D3 |
| J6-12 | - | - | - | - |
| J6-13 | - | - | - | - |
| J6-14 | - | - | - | - |
| J6-15 | - | - | - | - |
| J6-16 | - | - | - | - |
| J6-17 | - | - | - | - |
| J6-18 | - | - | - | - |
| J6-19 | - | - | - | - |
| J6-20 | - | - | - | - |
| S5U13C00P01C100 Board | STM32 Nucleo-144 development board | Description | ||
|---|---|---|---|---|
| Signal | Signal | |||
| J7-1 | - | - | - | |
| J7-2 | GND | GND | CN10-5 | Ground |
| J7-3 | - | - | - | - |
| J7-4 | - | - | - | - |
| J7-5 | - | - | - | - |
| J7-6 | - | - | - | - |
| J7-7 | - | - | - | - |
| J7-8 | - | - | - | - |
| J7-9 | - | - | - | - |
| J7-10 | - | - | - | - |
| J7-11 | - | - | - | - |
| J7-12 | - | - | - | - |
| J7-13 | - | - | - | - |
| J7-14 | - | - | - | - |
| J7-15 | - | - | - | - |
| J7-16 | HIFCS | PD7 | CN9-2 | Host INDIRECT8 chip-select |
| J7-17 | - | - | - | - |
| J7-18 | - | - | - | - |
| J7-19 | - | - | - | - |
| J7-20 | - | - | - | - |
Parts List
The following table lists the components used on the S5U13C00P01C100 board:
| Item | Qty | Reference | Part | Description | Manufacturer Part No. / Comments |
|---|---|---|---|---|---|
| 1 | 1 | CN1 | HEADER 2X8 | CONN HEADER 16POS (2x8) 0.1" right-angle | Amphenol FCI 68021-216HLF |
| 2 | 1 | CN2 | CONN_FLEX_24 | CONN FPC/FFC 24POS 0.50MM pitch | Panasonic AYF532435 |
| 3 | 10 | C0,C1,C4,C5, C6, C7, C8, C9, C12,C31 | 1uF | 1.0uF Ceramic -20%/+80% 25V Y5V C0805 | Samsung CL21F105ZAFNNNE |
| 4 | 2 | C3,C11 | 4.7uF | 4.7uF Ceramic 10% 25V X7S C0805 | Samsung CL21Y475KAFNNNE |
| 5 | 1 | C10 | 10uF | 10uF Ceramic 10% 25V X5R C0805 | Samsung CL21A106KAYNNNE |
| 6 | 1 | C13 | 3.3uF | 3.3uF Ceramic 10% 10V X5R C0805 | Samsung CL21A335KPFNNNE |
| 7 | 4 | C14,C16, C22,C23 | 0.1uF | 0.1uF Ceramic 10% 50V X7R C0603 | Samsung CL10B104KB8NNNC |
| 8 | 20 | C15,C17,C18,C19, C20, C21, C26,C27,C28, C29, C30, C32, C33, C35, C36, C37, C38, C39 C40,C41 | 1uF | 1uF Ceramic -20%/+80% 25V Y5V C0805 | Samsung CL21F105ZAFNNNE |
| 9 | 2 | C24,C25 | Not mounted | 10pF Ceramic 0.25pF 50V C0G/NP0 C0603 | Samsung CL10C100CB8NNNC |
| 10 | 3 | D1,D2,D3 | DIODE_SCHOTTKY | Diode Schottky 30V 500mA SOD123 | ON Semi MBR0530 |
| 11 | 1 | D4 | DIODE | Diode Schottky 30V 200mA SOD123 | Micro Commercial BAT42W-TP |
| 12 | 3 | JP2,JP3,JP4 | HEADER 1X2 | CONN HEADER 2POS 0.1" | Honda Tsushin FFC-52AMEP1-2P |
| 13 | 2 | JP6,JP7 | HEADER_1X3 | CONN HEADER 3POS 0.1" | Honda Tsushin FFC-52AMEP1-3P |
| 14 | 4 | J4,J5,J6,J7 | HEADER_10X2 | CONN HOUSING 20POS 2.54MM DUAL | Hirose HIF3H-20DA-2.54DSA(71) |
| 15 | 1 | J8 | Not mounted | CONN HEADER 18POS (2x9) 0.1" | Hirose A1-18PA-2.54DSA(71) |
| 16 | 1 | J9 | Not mounted | CONN HEADER 4POS 0.1" | Honda Tsushin FFC-52AMEP1-4P |
| 17 | 1 | J10 | Not mounted | CONN HEADER 2POS 0.1" | Honda Tsushin FFC-52AMEP1-2P |
| 18 | 1 | LED1 | LED +3.3V Green | LED GREEN DIFFUSED 1608 SMD | Stanley Electric BG1111C-TR |
| 19 | 1 | L1 | 10uH | 10uH 510mA 540mOhm wirewound inductor | Taiyo Yuden NR3010T100M |
| 20 | 1 | Q3 | N-CH FET | MOSFET N-CH 30V 3.2A SOT23 | ON Semi NTR4170NT1G |
| 21 | 1 | R3 | 0.47 | 0.47 OHM 5% 1/10W R0603 | Stackpole RMCF0603JTR470 |
| 22 | 27 | R4, R5,R6, R7, R9,R10,R11, R12, R13,R16,R20, R21, R24, R25,R29,R33, R34, R35,R36, R37,R38,R39,R40, R43,R45, R46,R49 | 0 | 0 OHM 1/10W R0603 | Stackpole RMCF0603ZT0R00 |
| 23 | 3 | R8,R19,R31 | 10K | 10K OHM 1% 1/10W R0603 | Stackpole RMCF0603FT10K0 |
| 24 | 2 | R14,R26 | 10 | 10 OHM 1% 1/10W R0603 | Stackpole RMCF0603FT10R0 |
| 25 | 1 | R15 | 100K | 100K OHM 5% 1/10W R0603 | Stackpole RMCF0603JT100K |
| 26 | 1 | R18 | 1K | 1K OHM 5% 1/10W R0603 | Stackpole RMCF0603JT1K00 |
| 27 | 1 | R41 | 560 | 560 OHM 5% 1/10W R0603 | Stackpole RMCF0603JT560R |
| 28 | 2 | R47,R48 | Not mounted | 10K OHM 5% 1/10W R0603 | Stackpole RMCF0603JT10K0 |
| 29 | 5 | SH2, SH3,SH4, SH6, SH7 | JUMPER | SHUNT BLACK 1x2 0.1" | Omron XJ8A-0211 |
| 30 | 1 | SW1 | SW TACT | SWITCH TACTILE SPST-NO 0.05A 16V | Alps SKRPABE010 |
| 31 | 1 | SW2 | SW TACT | SWITCH TACTILE SPST-NO 0.05A 24V | Omron B3FS-1010P |
| 32 | 1 | U1 | S1D13C00 | Epson S1D13C00 TQFP13-64 | Epson S1D13C00L00C000 |
| 33 | 1 | U2 | IS25LP-128 | 16Mbytes SPI Flash Memory | ISSI IS25LP128-JBLE |
| 34 | 1 | U4 | MCP1700 | 3.3V LDO | Microchip MCP1700T-3302E/TT |
| 35 | 1 | Y1 | FC-135 | 32.768KHz Crystal | Epson FC-135 32.7680KA-K |
S5U13C00P01C100 Schematics
S5U13C00P01C100 Schematics (1 of 2): This schematic diagram details the S1D13C00 EPD Controller, its connections to various components like memory (U2), connectors (CN1, CN2, J4, J5, J6, J7, J8, J9, J10), jumpers (JP2, JP3, JP4, JP6, JP7), and power circuitry. It illustrates the data bus, control signals, and interface connections.
S5U13C00P01C100 Schematics (2 of 2): This schematic diagram covers the peripheral circuits, memory LCD I/F Connector, external EPD board interface, power management, and push switch functionalities. It shows connections to U4 (MCP1700), LED1, and various interface connectors (J8, CN1, CN2, J4, J5, J6, J7).
Revision History
| Rev. No. | Date | Page | Category | Contents |
|---|---|---|---|---|
| 1.0 | 23/01/2019 | • Released as Rev 1.0 |
Further Information and Support
For more information on the S1C13C00 and other Epson Display Controllers, visit the Epson Global website:
https://global.epson.com/products_and_drivers/semicon/products/display_controllers/
For Sales and Technical Support, contact the Epson representative for your region:
https://global.epson.com/products_and_drivers/semicon/information/support.html
Document Code: XB8A-G-001-01.0
First Issue: August 2018
Revised: January 2019
