Instruction Manual for COXTOD models including: AM-1, AM-2, AM-3, AM-1 Oxygen Concentrator, Oxygen Concentrator, Concentrator
File Info : application/pdf, 8 Pages, 1.08MB
DocumentDocumentThe product packing list No. Category 1 Oxygen Concentrator 2 Nasal Cannula 3 Headset Oxygen Cannula 4 Power Line 5 Inlet Filter Cotton 6 HEPA Filter 7 Instructions for use 8 Fuse 9 Warranty card 10 Neulizer 11 Vehicle Power Inverter 12 External battery 13 Trolley Bag 26 Quantity One Set One Piece One Set One Piece Two Pieces One Piece One Piece One Piece One Piece One Set Power Indicator Oxygen Flow indicator Timing Indicator Total working time indicator Single running time indicator Anion function indicator Nebulization function indicator Power switch Timing/continue mode switch 16 Timing adjusting Contents Note Foreword..........................................................................................................................5 Safety notice.....................................................................................................................6 Attention...........................................................................................................................7 Product introduction.........................................................................................................10 N, NW model D Optional for AM 1L Optional for AM 1L O Optional Scope of application.........................................................................................................11 Products use environment............................................................................................. 11 Model specification........ ..................................................................................................12 Specification.....................................................................................................................13 Name and function of each part.......................................................................................14-16 3 XSpeTcification Remote control signal receiving port Alarm indicator O Hour CTime indicator Funtion Rated power(VA) Type AM-1 AM-1-W AM-1-N AM-1-NW AM-2 AM-2-W AM-2-N AM-2-NW AM-3 AM-3-W AM-3-N AM-3-NW 90 135 210 Working voltage 220V 5060Hz / 110V 5060Hz Rated flow (L/min) 1 2 3 Oxygen concentrations(V/V) 93±3% Anion yes yes yes Power Failure Alarm yes yes yes Temperature Alarm yes yes yes Purity Alarm no yes no yes no yes no yes no yes no yes Nebuzlier no no yes yes no no yes yes no no yes yes Minute Dust removal indicator The machine noisecdBcA 40 45 48 The weight cKg 7.2 7.7 7.4 Overall dimensionscmm 325×196×325 The oxygen outlet pressurecKPa 40 Anion/ Nebulization mode switch Nebulization outlet pressure(MPa) Remote Control no >0.1 Optional no >0.1 Optional no >0.1 Optional Flow adjusting Use in car by power inverter Optional Non-option Non-option External battery Optional Non-option Non-option Trolley bag Optional Optional Optional 13 Transportation and storage conditions Operation steps.............................................................................................................17-19 Maintenance instructions...............................................................................................20-22 Trouble shooting guide..................................................................................................22-24 Ambient temperature range:-20-45¥ Range of relative humidity: 95% or less The atmospheric pressure range: 500 ~ 1060 hpa Transportation and storage conditions...............................................................................25 Warranty ..............................................................................................................25 The product packing list .....................................................................................................26 Attached with oxygen concentrator principle diagram Attached with oxygen concentrator electric circuit diagram OD 4 T Name and function of each part COX Panel Handle Outer shell Air Inlet Window Air Inlet Filter HEPA Filter Warranty Whole device Maintenance Scope: See Maintenance Card for details. Paid Service Scope:When service period exceeds one year, paid maintenance service will be provided for service lifetime. Damage caused by natural disaster.Failure to present Maintenance Card or purchase invoice. S/N in Maintenance Card is inconsistent with device that needing maintenance. During warranty period, we will only provide paid maintenance instead of free maintenance for the following malfunction caused by users. Malfunction caused by unauthorized dismantling or refitting; Malfunction caused by the careless drop in use or handling; Malfunction caused by lack of reasonable maintenance; Malfunction caused by failure to operate the product in accordance with the proper guide in these instructions. 25 Fastening screw Back shell The oxygen outlet Humidification cup Clasp hands Of side window Label for technical parameters Power socket Clasp hands of Humidification cup Pedestal Exhaust port (bottom) Fuse holder 14 15 Foreword Thank you for purchasing the oxygen concentrator of our company ,and we hope you are satisfied with our products. 4 Remote control can not start oxygen concentrator after the power supply is connected There is no battery/cell inside remote control; Remote control is too far from oxygen concentrator or open angle too wide; Remote control is damaged or remote control port on the panel is damaged. Change battery; Adjust the distance or the angle between remote control and the receiveing port on the machine; Contact after-sales maintenance personnel This instruction manual describes the product's function, operation steps and matters needing attention, as well as the basic fault exclusion, etc. In order to be able to safely use this product, please read the instruction manual carefully before use. After oxygen Nasal cannula is kinked or damaged concentrator works Air leakage occurs in the interface of there is no or a little humidifier cup and machine oxygen at the 5 oxygen outlet and Air inlet filter or HEPA filter is blocked there are no obvious bubbles in D the humidifier cup. Internal faults Straighten out or change nasal cannula Re-install humidifier cup Check and clean air inlet filter or change HEPA filter Contact after-sales maintenance personnel Note: All alarms of oxygen concentrator are medium priority. When alarms occur, please contact the manufacturer or after-sales maintenance personnel in a timely manner. O 24 After reading, please properly keep it in order to look up for reference at any time. Please note that due to product improvements, We apologize if some of the illustrations in this instruction manual might not be completely the same with what you see in the machine 5 AtteTntion Pay attention ! c6Cleanliness of nebulizer: X After using nebulizer and connecting pipe, rinse them with detergent and clean water; wash nebulization mouth and mask with clean water first, then soak in medical alcohol for 5 minutes or sterilize and disinfect it in ultraviolet light, then rinse it with clean water again, put it in the sack after drying. Trouble shooting guide O No. failure phenomenon causes elimination method C Power failure alarm After Power plug is not plugged properly; Check whether the power plug is The device shall be used in a clean, dustless and well-ventilated space without toxic gas, where it will not be corroded. To prevent the device from damaging, please do not run the device before the installation of its high efficiency filter, or complete drying of intake filter cotton. When using the device, ensure that the exhaust from the bottom vent is being expelled properly, otherwise the device may overheat. Laying the device on its side or inverting is strictly prohibited during handling. Clean water in the bubble humidifier cup shall be poured out to prevent water backflow when transporting the device. pressing the power switch Indoor power socket is electrically plugged properly; There will be intermittent exhaust sound when using the device (the interval is about 5 seconds). 1 oxygen concentrator has neutral; Check the indoor power supply; a continuous hum, Circuit board of oxygen concentrator Contact after-sales maintenance personnel; The device shall not be started or stopped frequently. The interval time of restart after stop shall not be less than 5 minutes. the machine doesn't work is damaged; Fuse is damaged Manually change fuse and check the reason ( that is to say air in the device must be exhausted completely to prevent air compressor from starting under pressure, 2 temperature alarm concentrator has a oxygen axial flow fan does not work contact after-sale maintenance personnel thus affecting its lifespan) When the machine is shutoff the fan will continue to operate for a period of time to facilitate to exhaust the hot air inside the machine. Bubble humidifier cup shall be filled with distilled water or cold boiled water, and the amount added shall be between the maximum and minimum scale lines. 22 7 Safety notice! Pay attention! This product is used for oxygen supplement, not for life support or life extension. And it is suggested that when using the device the patient's oxygen flow and inhalation time shall be set according to doctor's guidance. Due to combustion effects of oxygen, please place the oxygen concentrator over 1.6 meters away from the objects which may produce sparks or bare electric line or flame and please use indoors. Please don't smoke when you are taking in oxygen or close to the ongoing oxygen users. discontinuous hum display shows E: 01 Machine stop working Bottom vent is blocked Check whether bottom vent is unblocked Please don't place the oxygen concentrator near the strong magnetic field or electromagnetic interference sources. Do not use nasal tube under cover or chair cushion,please be careful not to twist or knot nasal tubes. Shut off the power switch when you are not taking in oxygen. Oil or grease are disabled on the oxygen concentrator. Before you do any maintenance work, please make sure that oxygen concentrator has been blackouts in case of electric shock. D To avoid electric shock, please don't open the oxygen concentrator shell on its own. If there is any quality problem, the customer shall not remove parts or maintenance without authorization. If you find the abnormal phenomenon such as alarm you should contact the dealer or manufacturer. Please don't pour liquid directly on the product shell, O oxygen concentrator shell are not allowed to use organic solvents or cleaning agent. 6 O2 concentration alarm. Compressor is damaged; Oxygen Concentrator 3 has alarm sound ,red Molecular sieve tank error; Contact after-sales maintenance personnel Contact after-sales maintenance personnel light is ON, and display Oxygen purity sensor board Contact after-sales maintenance personnel shows E: 03 is damaged 23 XT In the oxygen concentrator, bubble humidifer cup, air inlet filter cotton, and high efficiency filter shall be cleaned. The bubble humidifier shall be cleaned about every 3 days, external air inlet filter cotton shall be cleaned about every 100 hours, and high efficiency filter shall be changed about every 1500 hours. O Please confirm the power is turned on with a smooth oxygen outlet. If the device stays idle for several days, please pour water in the bubble humidifier cup out entirely and dry it. Nasal cannula that conform to the supporting product specifications must be used. If other nasal cannula are used, C check carefully that they are closely and reliably connected to the oxygen concentrator. Nasal cannula is for one-time (4) Change of high efficiency filter (can be done by user): Replace the hepa filter of the oxygen concentrator after using every 1500 hours. Open the the inlet window on the right side of the machine shown in figure, to remove the old high efficiency filter, and install the new high efficiency filter . (5) Change of fuse: use or for the user only. After using, nasal cannula shall not be thrown away and shall be carried out in accordance with medical waste classification treatment to prevent the environment pollution. The fuse is under the power switch at the back of the machine as shown in the figure below, unscrew fuse socket with a screwd river,replace it with the new fuse,then screw the fuse socket well. To prevent cross contamination, nasal cannula and nebulizer shall be just for one person. Effective distance of remote control is 5m. When the effect is bad, please s-horten the distance or replace the remote control cell. Nebulizer should be used with the medical device registration certificate. 8 21 Maintenance instructions 1) Cleanliness of humidifier cup (can be done by user) *Remove humidifier cup from the machine. Wash and clean it with warm water and tableware detergent and rinse it clean with clean water. *Mix white vinegar with hot water in a ratio of 1:3, soak the humidifier cup in the mixture for 30 minutes for sterilization. *After rinsing humidifier cup thoroughly with warm water, dry it and set aside. - AM-1 type with car use requires car cigarette lighter load electric power of more than 240 W (2) Cleanliness of shell (can be done by user) ( fuse loads electric current of more than 20A) and output voltage DC12V. Please use a clean and soft wet towel with a little neutral furniture detergent to clean the enclosure, wipe out all parts of the enclosure, and then use dry towel to dry it. Clean 1-2 times(s) per month. Be sure that the device is fully powered down before beginning cleaning. . (3) Cleanliness of air inlet filter (can be done by user) Remove the air inlet window on both sides as shown in figure 3. Take out the inlet filter cotton, then wash and clean them with warm water and tableware detergent D and rinse it clean with clean water and remove any excessive moisture. Then let it air dry, and re-install the filter after it has completely dried. Figure 3 O 20 T (4) Adjust oxygen flow as needed by flow adjusting button. *Boot display is previous use mode XScope of application *Screen display the approximate oxygen concentration at corresponding flow. (5) Insert the inlet terminal of nasal cannula to the oxygen outlet, place the nasal cannula over the user's ears, and insert the nasal plug of nasal cannula into the nares of the user for oxygen intake. It is advisable to do oxygen therapy for 30-60 minutes every time. (6) After using the device, turn off the power switch. If the device is not going to be used again in the near future, O Product Use Environment please unplug the power plug. (7)Timing oxygen inhalation. When the user needs timing oxygen inhalation press Timing/continue mode switch key first, then timing function indicator flashes on the screen , and press timing adjusting key to set C the timing time as needed(10 minutes every interval and 5 hours at maximum),then press Timing/continue mode This equipment is mainly suitable for making health care with oxygen. Ambient temperature: 10 to 40 ; Relative humidity: 30% ~ 85%; 9 switch key to enter into timing oxygen inhalation state with timing function indicator keeping on. Atmospheric pressure: 700 hpa and 1060 hpa; Under timing state, the user may press Timing/continue mode switch key to enter into continuous state. (8)The use of remote control. Ensure power is connected first, aim remote control at Remote Control Port on oxygen No corrosive gas environment and strong magnetic field. concentrator, and then press keys on remote control to start oxygen concentrator. The functions of keys on remote control are the same with the ones on the panel of oxygen concentrator. Figure 1 18 11 Product introduction Principle: This product is a kind of small portable oxygen concentrating equipment, which uses the principle of Pressure Swing Adsorption(PSA). With air as the raw material and zeolite molecular sieve(ZMS) as the absorbent, it separates oxygen from nitrogen and other gases in the air and then, after being power on and under normal 9)Anion function. It can start by pressing the anion keys on the panel or on remote control, then the icon lights up. 10) Nebulization function. Put liquid drug inside the bottle according to the doctor's advise, tightly capped bottle cup of liquids, connect one end of the tube of connection interface of the nebulizer to oxygen outlet on the oxygen concentrator (as shown in figure 2). Press Nebulization key on the operation panel or remote control. When the icon lights up, nebulization treatment starts. temperature and pressure, oxygen with high purity can be continuously separated from the air. Nebulization mouth The use of the product will not affect oxygen content of the surrounding air. For working principles, please refer to the schematic diagram. Composition: This product is composed by oxygen-generating host, flow indicator, alarm system and nebulization interface (optional). It adopts the principle of pressure swing adsorption with a molecular sieve bed to generate D 90%-96% oxygen. O 10 Liquid bottle Connection to oxygen outlet on oxygen concentrator 11)The use of vehicle type inverter: Figure 2 Before use, please confirm that the car cigarette lighter power is in accordance with the requirements; Please insert the vehicle-mounted inverter to cigarette lighter interface after car start, so as to avoid car instantaneous current strike damage; Please pulls outinverter cable from the cigarette lighter after using it . 19 Model specification XOpTeration steps Function Code (Without function code: standard; W:with Low purity alarm; N: with nebulization outlet interface; NW: with low purity alarm and nebulization outlet interface) Flow Code (1,2 and 3 separately show rated flow 1L/min, 2L/min and 3L/min) O AM series portable oxygen concentrator Example: C AM-1 represents standard one with rated flow 1L/min; 1) Oxygen concentrator shall be placed in such a place with an easy oxygen supply and good ventilation, and shall be kept at least 20 cm away from the surrounding walls, curtains, and other objects. 2) Remove the humidifier cup, inject appropriate amount of distilled water or cold boiled water between the maximum scale line and minimum scale line, and then re-install the humidifier cup ( reference to the diagram). Remove humidifier cup according to this direction Oxygen entrance Clasp hands of humidifier cup AM-1-W represents with low purity alarm on AM-1 basis; water filling nozzle AM-1-N represents with nebulization outlet interface on AM-1 basis; Water line for reference AM-1-NW represents with low purity alarm and nebulization outlet interface on AM-1 basis. Install the humidifier cup according to this direction * This product types are subject to change without prior notice, please understanding. 3) Connect the power, insert one end of the power line into the oxygen concentrator's power socket; insert the other end of power line into an indoor power socket, and turn on the power switch. 12 17 Series AM oxygen concentrator for Medical use Instruction for use OXTOD SeriesAM C oxygen concentrator for Medical use Instruction for use Oxygen concentrator principle diagram Oxygen concentrator electric circuit diagram The raw material air nitroge nitroge Solenoid valve High purity oxygen AM-1/2 LED LED board Transformer out Compressor Fan Anion Flow valve mouth Transformer in Solenoid valve Fuse Control PCB Nebulization valve AC in Hepa filter humidifier cup Solenoid valve sensor 2 Molecule sieve tank Molecule sieve tank The condenser D oil free air compressor Flow meter AM-3 LCD Solenoid valve Compressor Fan Anion Flow valve LCD board Transformer in Control PCB Fuse AC in Nebulization valve TO Oxygen concentrator principle diagram Molecule sieve tank Molecule sieve tank X The raw material air O Hepa filter C The condenser nitroge nitroge Solenoid valve High purity oxygen humidifier cup Flow meter Oxygen concentrator electric circuit diagram AM-1/2 LED LED board Transformer out Compressor Fan Anion Flow valve mouth Transformer in Solenoid valve Fuse Control PCB Nebulization valve AC in Solenoid valve sensor 27 AM-3 Solenoid valve Compressor Fan Anion Flow valve oil free air compressor LCD LCD board Transformer in Control PCB Fuse AC in Nebulization valve 2 27Adobe PDF library 15.00 Adobe Illustrator CC 2017 (Windows)