Installation Guide for HiBOOST models including: Dot 2.0 Cell Phone Signal Boosters, Dot 2.0, Cell Phone Signal Boosters, Phone Signal Boosters, Signal Boosters, Boosters
HiBoost Cell Phone Booster Installation Guide and User Manuals
07 Step 5 Adjust and fix the Outdoor Antenna Step 6 Connect the indoor antenna with the booster Step 7 Adjust the indoor antenna Place the signal booster on a table and make sure the booster is within the coverage area. Have your outdoor antenna pointed to the cell tower
Dot Cheap Cell Phone Signal Booster | Hiboost
Installation Guide Mini Series Dot 2.0 Dot 2.0 Package Contents Signal Booster Outdoor Antenna Outdoor Cable 49.2ft NM-SMAM Indoor Whip Antenna Power Supply Accessories for main parts are all provided Booster Light Patterns waterproof tape to protect connections Alarm(ISO) Bluetooth Wi-Fi ALARM(ISO) Bluetooth LED Wi-Fi LED LED STATUSINDICATORS solid blue normal slow flashing blue quick flashing blue slight loopback loopback quick flashing red booster automatically shut off due to strong loopback/overload slow flashing blue bluetooth disconnected quick flashing blue bluetooth connected solid blue wifi disconnected slow flashing blue wifi connected 01 Bands contained in the Gauges on Signal Supervisor Gauge Band Uplink LTE700 12/17 13 698-716MHz 776-787MHz CELL800 5 824-849MHz Please focus on the gauge that contains the band you are using Downlink 728-746MHz 746-757MHz 869-894MHz Getting Started Step 1 Connect the Power Supply to the Booster Power Supply Signal Booster Step 2 Connect the Booster with the App Register an ID first and log in. Add the booster to the device list. 02 Step 3 Find the cell tower & Determine the outdoor antenna's position 3.1 Find the band you are using For Android Download NetWork Cell Info Lite in the Google store and open it. It can be seen from the example picture that the frequency band is band 13. (According to the form before, you need to pay attention to Gauge LTE700) Then click MAP. You can see your phone connecting to a tower, and you can try aiming your outdoor antenna at it. But sometimes this is not accurate. You could also move to Step 3.2 to find the tower Note: Please take screenshots at this stage. 03 For ios AT&T AT&T (1) Dial *3001#12345#* (2) Follow the instructions, take the screenshots as required. 3.2 Find the cell tower (1) Enter cellmapper.net (2) Choose your own carrier and band here. 04 (3) Then enter the coordinate of where you are trying to install the signal booster, and press Enter key. (In fact when you open Cellmapper, the map on the right will automatically locate your area if you've given the site permission to access your location. If you found tower sites not even displayed on the map, it might because the app intercepts the locations for security reasons.) (4) After the map jumps to the location, you can scroll the mouse pulley and zoom it out, then you will see the tower near the location. It would be better to take a screenshot of this page to guide the following installing steps. Should you have any questions, please contact our tech support. Note: If you need help finding the tower, please contact our tech support and provide your carrier, band and screenshots taken in the last steps. 05 3.3 Determine the outdoor antenna' s position The outdoor antenna is usually placed at one of the 4 ends of the roof. Please choose the position according to the tower' s location. Make sure there are no barriers between the antenna and the tower. Step 4 Connect the outdoor antenna with the booster Outdoor Antenna Outdoor Cable 49.2ft SMAM-NM Signal Booster NoteAt this stage, don' t connect the indoor antenna to the booster. 06 Step 5 Adjust and fix the Outdoor Antenna Have your outdoor antenna pointed to the cell tower you found before and observe the reading on the app. Adjust the outdoor antenna accordingly. Notes: (1) The output power should be the higher the better. (2) The full output power for Dot is 10dBm. And the full gain is 60dB. Step 6 Connect the indoor antenna with the booster Step 7 Adjust the indoor antenna Place the signal booster on a table and make sure the booster is within the coverage area. Make sure that the gain reaches about 60dB. If not, please increase the vertical and horizontal distance between the two antennas or add some barriers. 07 Step 8 Signal quality test You could do the following: (1)First make sure the signal gauge value is unchanged from that during the outdoor antenna installation. (2)Do speed tests with the booster on and off, and make a comparison. (3)Check if the number of signal bars increases. (4)Make a phone call or send messages and check if the voice and streaming are better. 4 Regular Problems and 1 normal status If the booster is working normally, no further adjustment is required OVERLOAD DL GAIN OUTPUT POWER LED LIGHT PATTERN REASON SOLUTION LTE700 <60dB CELL800 <60dB >=8dBm >=8dBm ISOcAlarm light blinking red Outdoor signal is too strong Have your outdoor antenna pointed slightly away from the cell tower LOOP BACK DL GAIN OUTPUT POWER LED LIGHT PATTERN REASON LTE700 <60dB CELL800 <60dB <8dBm <8dBm ISOcAlarm light blinking blue or red Inadequate separation of the indoor and outdoor antennas SOLUTION 1aIncrease vertical and horizontal distance. 2aAdd barriers(e.g. walls) Please try these solutions until the gain reaches or is over 60dB. POOR SIGNAL DL GAIN OUTPUT POWER LED LIGHT PATTERN REASON LTE700 >=60dB --/NEGATIVE CELL800 >=60dB --/NEGATIVE ISOcAlarm light solid blue Input signal is too weak SOLUTION 1aTry adjusting the outdoor antenna to the best direction 2aTry adjusting the outdoor antenna to another cell tower 3aTry increasing the height of the outdoor antenna and make sure there are no barriers between the tower and the outdoor antenna Please try these solutions until the output power reaches or is over -5dBm. 08 DL GAIN OUTPUT POWER Normal but No Boosted Signal LED LIGHT PATTERN REASON LTE700 >=60dB >=-5dBm CELL800 >=60dB >=-5dBm ISOcAlarm light solid blue 1aThe band is not supported 2aThe Signal is from other carriers SOLUTION Check the band you are using again. If it stays at band66,get into the 'detail'/'setting' of gagues on Signal Supervisor and switch off RF switch of AWS2100, then adjust the outdoor antenna again. It would be better if there are two persons and one can stay near the indoor antenna to check if the signal is boosted. DL GAIN OUTPUT POWER LTE700 >=60dB >=-5dBm CELL800 >=60dB >=-5dBm NORMAL LED LIGHT PATTERN ISOcAlarm light solid blue REASON SOLUTION Note: Some customers have some misunderstandings about boosters, and we would like to clarify it here: If you can't even get a stable 1 bar outside the house or on the roof, then we suggest you return it as it won't work in areas with very weak signal, the same is true of all boosters on the market. Technical Specifications Model No. Working Band UL Frequency Range(MHz) DL Frequency Range(MHz) Supported Standards Max. Gain Max. output power MGC (Step Attenuation ) I/O Port Impedance Environment Conditions Dimensions Weight Power Supply Dot Band 5 / Band 12 / Band 13 824-849/698-716/776-787 869-894/728-746/746-757 CDMA, LTE 60 dB UL 18 dBm,DL 10dBm 25 dB / 1 dB step SMA-Female 50 ohm IP40 6.77*4.41*0.75in 3.3 lbs / 1.5 kg Input AC100~240 V, 50/60 Hz, Output DC 5 V / 3 A 09 For more information Download Signal Supervisor or enter our website. wwwhiboost.com. a. You can download the specific user manual. b. You can reach our technical support for help. 10 3150 Premier Drive,Suite 130, Irving, TX 75063 (972) 870-5666 service@hiboost.com www.hiboost.comAdobe PDF library 15.00 Adobe Illustrator CC 23.0 (Windows)